2008 Peugeot 407 C Dag key
[x] Cancel search: keyPage 80 of 211
4
72
SUNROOF
To tilt the roof: press and hold part A
of the switch.
To open the roof in sliding mode: tilt
the sunroof, then press part A of the
s w i t c h b r i e fl y .
To close it in sliding mode: press
part B o f t h e s w i t c h b r i e fl y .
To close it in tilt mode: press and
hold part B of the switch.
S a f e t y a u t o - r e v e r s e
When the sunroof is sliding closed and
meets an obstacle, it stops then par-
tially opens again. Pressing the locking button
on the remote control key for
more than 2 seconds closes
the sunroof in sliding mode.
The sunroof remains tilted.
To close the sunroof completely, press
and hold part B of the switch before
getting out of the vehicle.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
Always ensure that the sunroof
is closed correctly before leaving the
vehicle.
In the event of contact during closing in
tilt mode, you must reverse the move-
ment of the roof. To do this, press the
switch concerned.
When the driver closes the roof in tilt
mode, he must ensure that no one is
preventing correct closing of the roof.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
Notes:
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), press and hold part
B
of the switch, w i t h i n t h e t w o s e c o n d s
which follow the triggering of the safety
auto-reverse, until the sunroof closes
completely.
Following reconnection of the bat-
tery or in the event of a malfunction,
press and hold part B of the switch,
the sunroof slides "step by step" until
it closes. Continue to press the switch
for approximately one second after
closing.
T h e s a f e t y a u t o - r e v e r s e f u n c t i o n i s
n o t a c t i v e d u r i n g t h e s e o p e r a t i o n s . S h u t t e r
The sunroof shutter is manual.
To open it, slide it rearwards using the
handle.
To close it, slide it forwards using the
handle.
D o n o t o p e n t h e s u n r o o f i m m e d i a -
t e l y a f t e r a s h o w e r o r i m m e d i a t e l y
a f t e r w a s h i n g t h e c a r .
Page 89 of 211
5
79
COURTESY LIGHTS
1 . F r o n t c o u r t e s y l i g h t
2 . Front map reading lights
With the ignition on, operate the relevant switch.
3 . R e a r c o u r t e s y l i g h t
4 . Rear map reading lights
With the ignition on, operate the relevant switch. Deactivation
The courtesy lights can be deacti vated
by pressing switch
1 for more than
three seconds. Pressing switch 1 or
3 b r i e fl y s w i t c h e s t h e c o r r e s p o n d i n g
courtesy light on and off.
The map reading lights are not affected
by this and can still be switched on.
Activation
To re-activate the automatic lighting,
press switch 1 again.
S i l l i l l u m i n a t i o n
The sill lighting is at the bottom of each
door trim.
The lights come on automatically
when a door is opened and switch off
automatically when all of the doors are
closed.
Boot light
The boot light is located in the right-
hand boot trim.
It comes on automatically when the
boot is opened and switches off auto-
matically when the boot is closed.
Pressing switch 1 or 3 switches on the
corresponding courtesy light for ten
minutes.
The front and rear courtesy lights come
on automatically when the ignition key
is removed, on unlocking the vehicle
or on opening one of the doors.
They gradually go off after the ignition
has been switched on or the vehicle
is locked.
Page 99 of 211
7
89
In the event of a malfunction
If this warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags may
no longer be deployed in the event of
a serious impact. Instrument panel warning light.
Disarming the front passenger's front air bag *
To ensure the safety of your child,
it is essential to disarm the pas-
senger air bag when you install a
rear- facing child seat on the front
passenger seat. Otherwise, the
child would risk being seriously in-
jured or killed if the air bag were to
i n fl a t e .
With the ignition switched off, in-
sert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the
key keeping the slot in this position. Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" posi-
tion to re-activate the air bag and thus
ensure its safety function.
* According to country. When the ignition is on, this
warning light remains lit on
the instrument panel for the
duration of disarming.
In the "OFF" position, the passen-
ger air bag will not be triggered in the
event of an impact. The steering column air bag protects
the driver's knees in the event of a
serious front impact.
It is incorporated in the fascia below
the steering column.
Steering column air bag
Activation
It is deployed at the same time as the
front air bags.
Page 102 of 211
7
89
In the event of a malfunction
If this warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags may
no longer be deployed in the event of
a serious impact. Instrument panel warning light.
Disarming the front passenger's front air bag *
To ensure the safety of your child,
it is essential to disarm the pas-
senger air bag when you install a
rear- facing child seat on the front
passenger seat. Otherwise, the
child would risk being seriously in-
jured or killed if the air bag were to
i n fl a t e .
With the ignition switched off, in-
sert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the
key keeping the slot in this position. Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" posi-
tion to re-activate the air bag and thus
ensure its safety function.
* According to country. When the ignition is on, this
warning light remains lit on
the instrument panel for the
duration of disarming.
In the "OFF" position, the passen-
ger air bag will not be triggered in the
event of an impact. The steering column air bag protects
the driver's knees in the event of a
serious front impact.
It is incorporated in the fascia below
the steering column.
Steering column air bag
Activation
It is deployed at the same time as the
front air bags.
Page 104 of 211
8
93
Gear selection gate
Move the lever in the gate to select
a position.
The indicator light corresponding to
the position selected appears on the
instrument panel screen.
P ark: to immobilise the vehicle and to
start the engine, with the handbrake on.
R everse: to reverse (select this posi-
tion with the vehicle stationary, engine
at idle).
N eutral: to start the engine and to park,
with the handbrake on.
Note: if position N is inadvertently en-
gaged while driving, allow the engine
to return to idle before engaging posi-
tion D then accelerate.
D rive: to drive in automatic mode.
M anual: to drive selecting the gears.
S: sport programme.
: snow programme.
'PORSCHE TIPTRONIC SYSTEM' AUTOMATIC GEARBOX
The six speed automatic gearbox
offers, as required, the comfort of the
auto-adaptive programme enhanced
by a selection suited to dynamic
driving conditions: sport, or to driving
on a slippery road: snow.
However, manual selection is still pos-
sible using the gear lever.
Moving Off
With the engine running, move off from
position P :
to exit position P, it is essential
to press the brake pedal,
select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
To move off from position N :
with your foot on the brake, release
the handbrake,
select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
Starting the engine
with the handbrake on, select posi-
tion P or N in the gate,
turn the ignition key. Always keep your foot on the
brake on a steep incline.
When the engine is at idle,
brakes not applied, if posi-
tion R , D or M is selected, the vehicle
moves even without the accelerator
being pressed.
Do not leave children unsupervised
inside the vehicle, with position
R, D or M selected, with the en-
gine running, as the vehicle moves
even without the accelerator being
pressed.
With the ignition off, if the
lever is not in position P , an
audible signal is heard when
the driver's door is opened, or
after approximately 45 seconds. Move
the lever to position P . The audible
signal ceases.
Page 117 of 211
9
107
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited. Cooling system CHECKING THE LEVELS
These are normal maintenance opera-
tions which keep your vehicle in good
working order. Consult the instruc-
tions in the PEUGEOT network, on
the Service Box site or in the servicing
booklet enclosed with this handbook.
Dipstick There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Oil level
Check the level regularly and top
up between changes.
Check the level with the vehicle level,
the engine having been off for more
than 15 minutes, using the dipstick.
Important: if you have to re-
m o v e / r e fi t t h e e n g i n e s t y l e c o v e r ,
handle it with care to avoid
d a m a g i n g t h e fi x i n g c l i p s . Oil change
It is imperative that this is carried out
a t t h e i n t e r v a l s s p e c i fi e d a n d t h e v i s c o -
sity of the oil chosen must meet the
requirements laid down in the manu-
facturer's servicing schedule. Consult
the instructions in the PEUGEOT
network or on the Service Box site.
Note: avoid used oil coming into
prolonged contact with the skin.
Empty the used oil into the containers
provided for this purpose in the
PEUGEOT network.
Oil filter
Replace the cartridge regularly in
accordance with the recommenda-
tions of the servicing schedule.
Brake fluid change
U s e t h e fl u i d r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l s D O T 4
Standards.
I t i s i m p e r a t i v e t h a t t h e b r a k e fl u i d i s
c h a n g e d a t t h e i n t e r v a l s s p e c i fi e d i n
accordance with the manufacturer's
servicing schedule.
Note: avoid all contact with the skin,
t h e b r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive. U s e o n l y t h e fl u i d r e c o m m e n d e d
by the manufacturer.
Note: the coolant does not need to be
changed.
When the engine is warm, the tempera-
ture of the coolant is controlled by the
engine fan. As this fan can operate with
the ignition key removed and because
the cooling system is pressurised, wait
for at least one hour after the engine
has stopped before carrying out any
work.
S l a c k e n t h e c a p t o t h e fi r s t
notch to release the pressure to
prevent any risk of scalding.
When the pressure has dropped,
remove the cap and top up the level with
coolant.
The engine fan can operate
after the vehicle has stopped.
Page 122 of 211
1010
111
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts.
Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l s p a r e
w h e e l , w h e n fi t t i n g i t , i t i s normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
t i a l r e m o v a b l e c o v e r w h i c h i s fi x e d
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
O n c e i t h a s b e e n fi t t e d o n y o u r v e h i -
cle, it is imperative that it is removed
when the ambient temperature condi-
tions rise above 10°C again.
Consult a PEUGEOT dealer.
* According to country.
Special features of alloy wheels
Anti-theft bolts
Y o u r w h e e l s a r e fi t t e d w i t h a n t i - t h e f t
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the anti-theft
socket and the wheel brace 1 .
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is
essential
to use special bolts available from your
PEUGEOT dealer.
Note: this anti-theft socket
was given to you on delivery
of your vehicle with the dupli-
cate keys. Make a careful note
of the code number engraved on the
head of the anti-theft socket. This will
enable you to obtain a duplicate anti-
theft socket from a Peugeot dealer.
You are advised to do the same for
the duplicate keys and not to leave the
c o n fi d e n t i a l c a r d i n t h e v e h i c l e .
Punctured tyre warning
light
Information on the instrument
panel:
T y r e u n d e r - i n fl a t i o n
detection system warning
light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
Page 123 of 211
1010
111
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts.
Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l s p a r e
w h e e l , w h e n fi t t i n g i t , i t i s normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
t i a l r e m o v a b l e c o v e r w h i c h i s fi x e d
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
O n c e i t h a s b e e n fi t t e d o n y o u r v e h i -
cle, it is imperative that it is removed
when the ambient temperature condi-
tions rise above 10°C again.
Consult a PEUGEOT dealer.
* According to country.
Special features of alloy wheels
Anti-theft bolts
Y o u r w h e e l s a r e fi t t e d w i t h a n t i - t h e f t
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the anti-theft
socket and the wheel brace 1 .
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is
essential
to use special bolts available from your
PEUGEOT dealer.
Note: this anti-theft socket
was given to you on delivery
of your vehicle with the dupli-
cate keys. Make a careful note
of the code number engraved on the
head of the anti-theft socket. This will
enable you to obtain a duplicate anti-
theft socket from a Peugeot dealer.
You are advised to do the same for
the duplicate keys and not to leave the
c o n fi d e n t i a l c a r d i n t h e v e h i c l e .
Punctured tyre warning
light
Information on the instrument
panel:
T y r e u n d e r - i n fl a t i o n
detection system warning
light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.