2008 NISSAN TEANA ignition

ADP-110
< COMPONENT DIAGNOSIS >
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000003940049
NOTE:
The details of time display are as follows.
 CRNT: A malfunction is detected now.
 PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data and IGN Counter, refer to
BCS-16, "
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
4 B2013: ID DISCORD BCM-S/L
 B2014: CHAIN OF S/L-BCM
 B2553: IGNITION RELAY
 B2555: STOP LAMP
 B2556: PUSH-BTN IGN SW
 B2557: VEHICLE SPEED
 B2560: STARTER CONT RELAY
 B2601: SHIFT POSITION
 B2602: SHIFT POSITION
 B2603: SHIFT POSI STATUS
 B2604: PNP SW
 B2605: PNP SW
 B2606: S/L RELAY
 B2607: S/L RELAY
 B2608: STARTER RELAY
 B2609: S/L STATUS
 B260A: IGNITION RELAY
 B260B: STEERING LOCK UNIT
 B260C: STEERING LOCK UNIT
 B260D: STEERING LOCK UNIT
 B260F: ENG STATE SIG LOST
 B2612: S/L STATUS
 B2614: ACC RELAY CIRC
 B2615: BLOWER RELAY CIRC
 B2616: IGN RELAY CIRC
 B2617: STARTER RELAY CIRC
 B2618: BCM
 B2619: BCM
 B261A: PUSH-BTN IGN SW
 B261E: VEHICLE TYPE
 B26E1: ENG STATE NO RES
 B26E9: S/L STATUS
 B26EA: KEY REGISTRATION
 U0415: VEHICLE SPEED SIG
5 B2621: INSIDE ANTENNA
 B2622: INSIDE ANTENNA
 B2623: INSIDE ANTENNA Priority DTC
CONSULT display Fail-safe Freeze Frame DataIntelligent Key warn-
ing lamp ONReference page
No DTC is detected.
further testing
may be required.————
U1000: CAN COMM CIRCUIT — — —BCS-33
U1010: CONTROL UNIT (CAN) — — —BCS-34
U0415: VEHICLE SPEED SIG — — —BCS-35
B2013: ID DISCORD BCM-S/L××—SEC-46
B2014: CHAIN OF S/L-BCM××—SEC-47
B2190: NATS ANTENNA AMP×——SEC-39
B2191: DIFFERENCE OF KEY×——SEC-42

BCM (BODY CONTROL MODULE)
ADP-111
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
B2192: ID DISCORD BCM-ECM×——SEC-43
B2193: CHAIN OF BCM-ECM×——SEC-45
B2553: IGNITION RELAY —×—PCS-49
B2555: STOP LAMP —×—SEC-50
B2556: PUSH-BTN IGN SW —××SEC-52
B2557: VEHICLE SPEED×××SEC-54
B2560: STARTER CONT RELAY×××SEC-55
B2562: LOW VOLTAGE —×—BCS-36
B2601: SHIFT POSITION×××SEC-56
B2602: SHIFT POSITION×××SEC-59
B2603: SHIFT POSI STATUS×××SEC-61
B2604: PNP SW×××SEC-64
B2605: PNP SW×××SEC-67
B2606: S/L RELAY×××SEC-69
B2607: S/L RELAY×××SEC-70
B2608: STARTER RELAY×××SEC-72
B2609: S/L STATUS×××SEC-74
B260A: IGNITION RELAY×××PCS-51
B260B: STEERING LOCK UNIT —××SEC-78
B260C: STEERING LOCK UNIT —××SEC-79
B260D: STEERING LOCK UNIT —××SEC-80
B260F: ENG STATE SIG LOST×××SEC-81
B2612: S/L STATUS×××SEC-85
B2614: ACC RELAY CIRC —××PCS-53
B2615: BLOWER RELAY CIRC —××PCS-55
B2616: IGN RELAY CIRC —××PCS-57
B2617: STARTER RELAY CIRC×××SEC-89
B2618: BCM×××PCS-59
B2619: BCM×××SEC-91
B261A: PUSH-BTN IGN SW —××SEC-92
B261E: VEHICLE TYPE××× (Turn ON for 15
seconds)SEC-95
B2621: INSIDE ANTENNA —×—DLK-50
B2622: INSIDE ANTENNA —×—DLK-52
B2623: INSIDE ANTENNA —×—DLK-54
B26E1: ENG STATE NO RES×××SEC-82
B26E9: S/L STATUS××× (Turn ON for 15
seconds)SEC-83
B26EA: KEY REGISTRATION —×× (Turn ON for 15
seconds)SEC-84
CONSULT display Fail-safe Freeze Frame DataIntelligent Key warn-
ing lamp ONReference page

ADP-112
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
ECU DIAGNOSIS
DRIVER SEAT CONTROL UNIT
Reference ValueINFOID:0000000003759211
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
Monitor Item Condition Value/Status
SET SW Set switchPush ON
Release OFF
MEMORY SW1 Memory switch 1Push ON
Release OFF
MEMORY SW2 Memory switch 2Push ON
Release OFF
SLIDE SW–FR Sliding switch (forward)Operate ON
Release OFF
SLIDE SW–RR Sliding switch (backward)Operate ON
Release OFF
RECLN SW–FR Reclining switch (forward)Operate ON
Release OFF
RECLN SW–RRReclining switch (back-
ward)Operate ON
Release OFF
LIFT FR SW–UP Lifting switch front (up)Operate ON
Release OFF
LIFT FR SW–DN Lifting switch front (down)Operate ON
Release OFF
LIFT RR SW–UP Lifting switch rear (up)Operate ON
Release OFF
LIFT RR SW–DN Lifting switch rear (down)Operate ON
Release OFF
DETENT SW Selector leverP position OFF
Other than above ON
STARTER SW Ignition positionCranking ON
Other than above OFF
SLIDE PULSE Seat slidingForward The numeral value decreases *
Backward The numeral value increases*
Other than above No change to numeral value*
RECLN PULSE Seat recliningForward The numeral value decreases*
Backward
The numeral value increases
*
Other than above
No change to numeral value*
LIFT FR PULSE Seat lifter (front)Up
The numeral value decreases
*
Down
The numeral value increases *
Other than above
No change to numeral value*

DRIVER SEAT CONTROL UNIT
ADP-113
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
*: The value at the position attained when the battery is connected is regarded as 32768.
TERMINAL LAYOUT
PHYSICAL VALUES
LIFT RR PULSE Seat lifter (rear)Up
The numeral value decreases
*
Down
The numeral value increases *
Other than above
No change to numeral value*
STEERING STATUS Steering lock unitLOCK LOCK
unlock UNLOCK
VEHICLE SPEED The condition of vehicle speed is displayed km/h
P RANG SW CAN Selector leverP position ON
Other than above OFF
R RANGE (CAN) Selector leverR position ON
Other than above OFF
DOOR SW-FL Driver doorOpen ON
Close OFF
DOOR SW-FR Passenger doorOpen ON
Close OFF
IGN ON SW Ignition switchON position ON
Other than above OFF
ACC ON SW Ignition switchACC or ON position ON
Other than above OFF
KEY ON SW Intelligent KeyInserted is key slot ON
Inserted is not key slot OFF
KEYLESS ID UNLOCK button of Intelligent Key is pressed 1,2,3,4or5
KYLS DR UNLKIntelligent Key or driver
side door request switchON ON
OFF OFF
VHCL SPEED (ABS) Can signal from ABSReceived ON
Not received OFF
HANDLE The BCM for handle position is displayedLHD
RHD
TRANSMISSIONTransmission type is dis-
played CVT Monitor Item Condition Value/Status
JMJIA2011ZZ

ADP-124
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
DTC Index
INFOID:0000000003759214
*1:
 0: Current malfunction is present
 1-39: Displayed if any previous malfunction is present when current condition is normal. The numeral value increases by one at each
IGN ON to OFF cycle from 1 to 39. The counter remains at 39 even if the number of cycles exceeds it. However, the counter is reset
to 1 if any malfunction is detected again, the normal operation is resumed and the ignition switch is turned from OFF to ON. Operating in
fail-safe modeMalfunction ItemRelated
DTCDiagnosis
Only manual functions operate normallyCAN communication U1000ADP-38
CONTROL UNIT U1010ADP-39
EEPROM B2130ADP-40
Only manual functions, except seat sliding, operate normally Seat sliding output B2112ADP-41
Only manual functions, except seat reclining, operate normally Seat reclining output B2113ADP-43
CONSULT-III
displayTiming
*1
Item Reference page
Current mal-
functionPrevious mal-
function
CAN COMM CIRCUIT
[U1000]0 1-39 CAN communicationADP-38
CONTROL UNIT
[U1010]0 1-39 Control unitADP-39
SEAT SLIDE
[B2112]0 1-39 Seat slide motor outputADP-41
SEAT RECLINING
[B2113]0 1-39 Seat reclining motor outputADP-43
EEPROM
[B2130]0 1-39 EEPROMADP-40

ADP-128
< SYMPTOM DIAGNOSIS >
MEMORY FUNCTION DOES NOT OPERATE
MEMORY FUNCTION DOES NOT OPERATE
ALL COMPONENTS
ALL COMPONENTS : Diagnosis ProcedureINFOID:0000000003759223
1.CHECK MANUAL OPERATION
Check manual operation.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Refer to ADP-125, "
ALL COMPONENTS : Diagnosis Procedure".
2.PERFORM INITIALIZATION AND MEMORY STORING PROCEDURE
1. Perform initialization procedure.
Refer to ADP-8, "
SYSTEM INITIALIZATION : Special Repair Requirement".
2. Perform memory storing procedure.
Refer to ADP-9, "
MEMORY STORING : Special Repair Requirement".
3. Check memory function.
Refer to ADP-19, "
MEMORY FUNCTION : System Description".
Is the inspection result normal?
YES >> Memory function is normal.
NO >> GO TO 3.
3.CHECK DTC
Check the following DTC.
Vehicle speed signal
 “Self Diagnostic Result” with ABS actuator and electric unit (control unit). Refer to BRC-48, "
DTC No. Index".
 “Self Diagnostic Result” with METER. Refer to MWI-67, "
DTC Index".
Selector lever in P position signal, ignition position signal and key slot signal.
 “Self Diagnostic Result” with BCM. Refer to ADP-110, "
DTCIndex".
 “Self Diagnostic Result” with TCM. Refer to TM-121, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK SEAT MEMORY SWITCH
Check seat memory switch.
Refer to ADP-54, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check front door switch (driver side).
Refer to ADP-58, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.
SEAT SLIDING

ADP-132
< SYMPTOM DIAGNOSIS >
ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE
ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000003759233
1.CHECK SYSTEM SETTING
1. Check system setting.
Refer to ADP-10, "
SYSTEM SETTING : Special Repair Requirement".
2. Check the operation.
Is the inspection result normal?
YES >> Entry/Exit function is OK.
NO >> GO TO 2.
2.PERFORM SYSTEM INITIALIZATION
1. Perform system initialization.
Refer to ADP-8, "
SYSTEM INITIALIZATION : Special Repair Requirement".
2. Check the operation.
Is the inspection result normal?
YES >> Entry/Exit function is OK.
NO >> GO TO 3.
3.CHECK DTC
Selector lever in Position signal, ignition position signal and key slot signal.
 “Self Diagnostic Result” with BCM. Refer to ADP-110, "
DTCIndex".
 “Self Diagnostic Result” with TCM. Refer to TM-121, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check front door switch (driver side).
Refer to ADP-58, "
Component Function Check".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.

AV
DIAGNOSIS SYSTEM (AUDIO UNIT)
AV-15
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DIAGNOSIS SYSTEM (AUDIO UNIT)
Diagnosis DescriptionINFOID:0000000003765592
Self-diagnosis mode can perform the following items.
 Versions display
 Channel check diagnosis
 Key check diagnosis
 AV communication diagnosis
VERSIONS DISPLAY FUNCTION
1. Turn ignition switch ON.
2. Turn the audio unit off.
3. While pressing “1” button, turn volume control dial clockwise or
counterclockwise for 30 clicks or more.
4. Diagnosis default screen of audio display unit is displayed.
NOTE:
Diagnosis default screen = All icons and segments of the audio display unit are turned on.
5. Pressing the AUDIO switch briefly displays the version display mode. Pressing the AUDIO switch briefly
switches to each version display. Pressing and holding the AUDIO switch when displaying each software
version returns to the diagnosis default screen.
Version display item
6. Self-diagnosis mode is canceled when the ignition switch is turned OFF.
CHANNEL CHECK DIAGNOSIS FUNCTION
1. Turn ignition switch ON.
2. Turn the audio unit off.
3. While pressing the “1” button, turn the volume control dial clock-
wise or counterclockwise for 30 clicks or more.
JSNIA1334GB
Mode Description
Ve r s i o n s d i s p l a ySoftware V###### Audio unit software version is displayed.
Hardware V###### Audio unit hardware version is displayed.
Disp HW V###### Display unit hardware version is displayed.
CD Mech V###### Audio unit CD mechanism version is displayed.
EEPROM V###### Audio unit EEPROM version is displayed.
Disp SW V###### Display unit software version is displayed.
JSNIA1334GB