2008 NISSAN TEANA battery

AV-82
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
AV CONTROL UNIT
AV CONTROL UNIT : Diagnosis ProcedureINFOID:0000000003901202
1.CHECK FUSE
Check for blown fuses.
Is inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between AV control unit harness connectors and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between AV control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect AV control unit connectors.
3. Check continuity between AV control unit harness connectors and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
DISPLAY UNIT
DISPLAY UNIT : Diagnosis ProcedureINFOID:0000000003901446
1.CHECK POWER SUPPLY CIRCUIT (DISPLAY SIDE)
Check voltage between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
Power source Fuse No.
Battery 31
Ignition switch ACC or ON 19
Ignition switch ON or START 4
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Battery power supply
M12719 OFF
Battery voltage ACC power supply 7 ACC
Ignition signal M131 104 ON
Signal name Connector No. Terminal No. Ignition switch position Continuity
GroundM127 20
OFF Existed
M131 85
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Inverter VCC
M492
ACC 9 V
Signal VCC 3

AV-84
< COMPONENT DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between multifunction switch harness connector and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between multifunction switch and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect multifunction switch connector.
3. Check continuity between multifunction switch harness connector and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT : Diagnosis ProcedureINFOID:0000000003901205
1.CHECK FUSE
Check for blown fuses.
Is inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUITS
Check voltage between camera control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between camera control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect camera control unit connector.
3. Check continuity between camera control unit harness connector and ground.
Is inspection result normal?
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
ACC power supply M125 3 ACC Battery voltage
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground M125 1 OFF Existed
Power source Fuse No.
Battery 31
Ignition switch ACC 19
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Battery power supply
B25132 OFF
Battery voltage
ACC power supply 30 ACC
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground B251 31 OFF Existed

AV
AV CONTROL UNIT
AV-107
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
2
(W)3
(B)Sound signal front LH OutputIgnition
switch
ONSound output.
4
(O/B)5
(W/R)Sound signal rear LH OutputIgnition
switch
ONSound output.
6
(W/G)15
(L/B)Steering switch signal A InputIgnition
switch
ONKeep pressing SOURCE
switch. 0 V
Keep pressing switch.0.7 V
Keep pressing switch.1.3 V
Except for above. 3.3 V
7
(V/W)Ground ACC power supply InputIgnition
switch
ACC— Battery voltage
9
(R/L)Ground Illumination signal InputIgnition
switch
OFFLighting switch is OFF. 0 V
Lighting switch is ON. 12.0 V
11
(B/W)12
(BR)Sound signal front RH OutputIgnition
switch
ONSound output.
13
(L)14
(B/W)Sound signal rear RH OutputIgnition
switch
ONSound output.
15
(L/B)GroundSteering switch signal
ground—Ignition
switch
ON—0 V
16
(GR/L)15
(L/B)Steering switch signal B InputIgnition
switch
ONKeep pressing VOL DOWN
switch.0 V
Keep pressing VOL UP
switch.0.7 V
Except for above. 3.3 V
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E

AV-108
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
AV CONTROL UNIT
19
(Y)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
20
(B/W)Ground Ground —Ignition
switch
ON—0 V
33 — FM sub Input — — —
34 — AM–FM main Input — — —
35 Ground Antenna amp. ON signal OutputIgnition
switch
ACC— 12.0 V
36
(B)Ground Composite image signal OutputIgnition
switch
ONWhen camera image or
AUX image is displayed.
37
(W)GroundComposite image signal
ground—Ignition
switch
ON—0 V
38
(B)Ground RGB image signal (B: blue) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
39
(R)GroundRGB image signal (G:
green)OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
40
(W)Ground RGB image signal (R: red) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
41
(G)Ground RGB synchronizing signal OutputIgnition
switch
ON— Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB2251J
SKIB2237J
SKIB2236J
SKIB2238J
SKIB3603E

AV
AV CONTROL UNIT
AV-111
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
*:Stereo sounds are input only when the 2 channel stereo sound is played.96
(B)97
(R)AUX sound signal LH InputIgnition
switch
ONAUX sound input.
101
(BR)Ground Switch ground —Ignition
switch
ON—0 V
103
(SB)Ground Disk eject signal InputIgnition
switch
ONPressing the eject switch. 0 V
Except for above. 3.3 V
104
(O)Ground Ignition signal InputIgnition
switch
ON— Battery voltage
105
(P/B)Ground Reverse signal InputIgnition
switch
ONSelector lever in R position. 12.0 V
Other than selector lever in
R position.0 V
106
(G/R)Ground Parking brake signal InputIgnition
switch
ONParking brake ON. 0 V
Parking brake OFF.
107
(V/W)GroundVehicle speed signal
(8-pulse)InputIgnition
switch
ONWhen vehicle speed is ap-
prox. 40 km/h (25MPH).NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
111 — S h i e l d — — — —Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
JSNIA0007GB
JSNIA0012GB

AV-148
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
26
(O)GroundVehicle speed signal
(8-pulse)InputIgnition
switch
ONWhen vehicle speed is ap-
prox. 40 km/h (25 MPH).NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
30
(V)Ground ACC power supply InputIgnition
switch
ACC— Battery voltage
31
(B/R)Ground Ground —Ignition
switch
ON—0 V
32
(Y)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
JSNIA0012GB

AV
PRECAUTIONS
AV-169
< PRECAUTION >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003960542
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Precaution for Trouble DiagnosisINFOID:0000000003882788
AV COMMUNICATION SYSTEM
 Do not apply voltage of 7.0 V or higher to the measurement terminals.
 Use the tester with its open terminal voltage being 7.0 V or less.
 Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Precaution for Harness RepairINFOID:0000000003882789
AV COMMUNICATION SYSTEM
 Solder the repaired parts, and wrap with tape. [Frays of twisted line
must be within 110 mm (4.33 in).]
 Do not perform bypass wire connections for the repair parts. (The
spliced wire will become separated and the characteristics of
twisted line will be lost.)
PKIA0306E
PKIA0307E

AV-182
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW CAMERA
3. Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.
4. Fine adjust the guiding line so that its position is aligned to the
correction line by pressing the up/down/left/right switches.
Pressing “ENTER” enable the camera control unit to memory
the adjusted guiding line position.
CAUTION:
Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
 Remove battery for five min. Then reconnect battery.
 Remove camera control unit connector for five min. Then reconnect camera control unit connec-
tor.Selected pattern : 7
Up/Down adjustment range : −20 – 20
Left/Right adjustment range : −20 – 20
SKIB3689E