2008 NISSAN TEANA Ccu

AV
NAVIGATION SYSTEM
AV-411
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
The current vehicle position will be calculated by detecting the dis-
tance the vehicle moved from the previous calculation point and its
direction.
 Travel distance
Travel distance calculations are based on the vehicle speed sen-
sor input signal. Therefore, the calculation may become incorrect
as the tires wear down. To prevent this, an automatic distance cor-
rection function has been adopted.
 Travel direction
Change in the travel direction of the vehicle is calculated by a gyro-
scope (angular velocity sensor) and a GPS antenna (GPS informa-
tion). They have both advantages and disadvantages.
More accurate traveling direction is detected because priorities are set for the signals from these two
devices according to the situation.
MAP-MATCHING
Map-matching compares a current location detected by the method
in the “Location Detection Principle” with a road map data from Map
DVD-ROM stored in DVD-ROM drive.
NOTE:
The road map data is based on data stored in the map DVD-ROM.
The vehicle position may not be corrected under the following circumstances and after driving for a certain
time when GPS information is difficult to receive. In this case, the vehicle mark on the display must be cor-
rected manually.
 In map-matching, alternative routes to reach the destination will be
shown and prioritized, after the road on which the vehicle is cur-
rently driven has been judged and the vehicle mark has been repo-
sitioned.
Alternative routes will be shown in different order of priority, and
the incorrect road can be avoided if there is an error in distance
and/or direction.
They are of the same priority if two roads are running in parallel.
Therefore, the vehicle mark may appear on either of them alter-
nately, depending on maneuvering of the steering wheel and con-
figuration of the road.
SEL684V
Type Advantage Disadvantage
Gyroscope
(angular velocity sensor)Can detect the vehicle's turning angle quite
accurately.Direction errors may accumulate when vehicle is
driven for long distances without stopping.
GPS antenna
(GPS information)Can detect the vehicle's travel direction
(North/South/East/West).Correct direction cannot be detected when vehicle
speed is low.
SEL685V
SEL686V

AV-412
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
NAVIGATION SYSTEM
 Map-matching does not function correctly when a road on which
the vehicle is driving is new and not recorded in the map DVD-
ROM, or when road pattern stored in the map data and the actual
road pattern are different due to repair.
The map-matching function may find another road and position the
vehicle mark on it when driving on a road not present in the map.
Then, the vehicle mark may change to it when the correct road is
detected.
 Effective range for comparing the vehicle position and travel direc-
tion calculated by the distance and direction with the road data
read from the map DVD-ROM is limited. Therefore, correction by
map-matching is not possible when there is an excessive gap
between current vehicle position and the position on the map.
GPS (GLOBAL POSITIONING SYSTEM)
GPS (Global Positioning System) was developed for and is con-
trolled by the US Department of Defense. The system utilizes GPS
satellites (NAVSTAR), sending out radio waves while flying on an
orbit around the earth at an altitude of approximately 21,000 km
(13,100miles).
The GPS receiver calculates the vehicle's position in three dimen-
sions (latitude/longitude/altitude) according to the time lag of the
radio waves received from four or more GPS satellites (three-dimen-
sional positioning). The GPS receiver calculates the vehicle's posi-
tion in two dimensions (latitude/longitude), utilizing the altitude data
calculated previously with radio waves from four or more GPS satel-
lites (two-dimensional positioning) if radio waves were received only
from three GPS satellites.
Position correction by GPS is not available while the vehicle is stopped.
Accuracy of GPS will deteriorate under the following conditions:
 In two-dimensional positioning, GPS accuracy will deteriorate when altitude of the vehicle position changes.
 The accuracy can be even lower depending on the arrangement of the GPS satellites utilized for the posi-
tioning.
 Position detection is not possible when vehicle is in an area where radio waves from the GPS satellite do not
reach, such as in a tunnel, parking lot in a building, and under an elevated highway. Radio waves from the
GPS satellites may not be received when some object is located over the GPS antenna.
NOTE:
 Even a high-precision three dimensional positioning, the detection result has an error about 10 m (30ft).
 Because the signals of GPS satellite is controlled by the Tracking and Control Center in the United States,
the accuracy may be degraded lower intentionally or the radio waves may stop.
SKIA0613E
SEL526V

AV-420
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
NOTE:
*: On-board self-diagnosis is not supported. Only CONSULT-III is supported.
STARTING PROCEDURE
1. Start the engine.
2. Turn the audio system OFF.
3. While pressing the “SETTING” button, turn the volume control
dial clockwise or counterclockwise for 40 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
 Shifting from current screen to previous screen is performed
by pressing “BACK” button.
Confirmation/
AdjustmentDisplay DiagnosisThe confirmations of the tint with the color spectrum bar display and
shading of color with the gradation bar display can be performed.
Vehicle SignalsDiagnosis of signals can be performed for vehicle speed, parking brake,
lights, ignition switch, and reverse.
Navigation/PhoneHandsfree Voice Mi-
crophone TestMicrophone speaker check can be performed.
Color Spectrum Bar A color tone can be checked by the color bar display.
Gradation Bar A light and shade can be checked by the gray scale display.
Touch Panel Touch panel response check can be performed.
Vehicle SignalsDiagnosis of signals can be performed for vehicle speed, parking brake,
lights, and reverse.
Confirm/Change
Bluetooth PasskeyThe passkey can be checked and changed.
Confirm/Change
Bluetooth Device
NameThe device name can be checked and changed.
Handsfree Sound
Quality SetNot available.
Speaker Test The connection of a speaker can be confirmed by test tone.
Climate Control
*Not used.
Error HistoryThe system malfunction and the frequency when occurred in the past are
displayed. When the malfunctioning item is selected, the time and place
that the selected malfunction last occurred are displayed.
Camera Cont.The signal connected to camera control unit can be checked and the
guiding line position that overlaps rear view camera image can be adjust-
ed.
Vehicle CAN Diagnosis The transmitting/receiving of CAN communication can be monitored.
AV COMM DiagnosisThe communication condition of each unit of Multi AV system can be
monitored.
Delete Unit Connection Log Erase the connection history of unit and error history.
Initialize Settings Initializes the AV control unit memory.Mode Description
JSNIA1290GB

AV-428
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Confirm/Change Bluetooth Passkey
 The passkey of Bluetooth can be confirmed and changed.
 The passkey can be changed by four to eight digits within the num-
ber of 0 to 9.
Confirm/Change Bluetooth Device Name
 The device name of Bluetooth can be confirmed and changed.
 The device name can be changed within the range of twenty digits
of alphabets and codes.
Speaker Test
Select “SPEAKER TEST” to display the Speaker Diagnosis screen.
Press “START and NEXT” to generate a test tone in a speaker.
Press “Start” to generate a test tone in the next speaker. Press “End”
to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Climate Control
On-board self-diagnosis is not supported. Only CONSULT-III is supported.
Refer to HAC-159, "
WITH INTELLIGENT AIR CONDITIONER SYSTEM : CONSULT-III Function" for details.
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The frequency of occurrence in error history is displayed in a count up manner. The actual count up method
differs depending on the error item.
Count up method A
LightsON Light switch ON.
—
OFF Light switch OFF.
ReverseON Selector lever in R position.
Changes in indication may be delayed. This is normal.
OFFSelector lever in any position other
than R. Diagnosis item Display Vehicle status Remarks
JSNIA0086GB
JSNIA0517GB
Tweeter : 3 kHz
Front door speaker : 300 Hz
Rear door speaker : 1 kHz
JSNIA0150GB

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-429
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the
condition is normal at a next IGN ON cycle.
 The counter upper limit is 39. Any counts exceeding 39 are ignored.“ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
 The counter increases by 1 if an error occurs when IGN switch is ON. The counter will not decrease even if
the condition is normal at the next IGN ON cycle.
 The counter upper limit is 50. Any counts exceeding 50 are ignored. “ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Error item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
Display type of occur-
rence frequencyError history display item
Count up method A CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B Other than the above
JSNIA0518GB
Error item Description Possible malfunction factor/Action to take
CAN COMM CIRCUITCAN communication malfunction is detect-
ed.Perform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
CONTROL UNIT (CAN)CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit. CONTROL UNIT (AV)AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
CAN Controller Memory Error
Amplifier Temperature Error BOSE amp. malfunction is detected. Replace the BOSE amp.
Front Display Connection ErrorWhen either one of the following items is
detected:
 display unit power supply and ground cir-
cuits are malfunctioning.
 serial communication circuits between
display unit and AV control unit are mal-
functioning.
 serial communication signal between
display unit and AV control unit is mal-
functioning. Display unit power supply and ground
circuits.
 Serial communication circuits between
display unit and AV control unit.

AV-462
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
U1300 AV COMM CIRCUIT
U1300 AV COMM CIRCUIT
DescriptionINFOID:0000000003765874
U1300 is indicated when malfunction occurs in communication signal of multi AV system. Indicated simulta-
neously, without fail, with the malfunction of control units connected to AV control unit with communication line.
Determine the possible malfunction cause from the table below.
Self-diagnosis results display item
DTCDisplay contents of
CONSULT-IIIDescriptionPossible malfunction factor/Action to
take
U1300
U1240 AV COMM CIRCUIT
[U1300]
 SWITCH CONN
[U1240]When either one of the following items is detected:
 multifunction switch power supply and ground circuits
are malfunctioning.
 AV communication circuits between AV control unit and
multifunction switch are malfunctioning.
 AV communication signal between AV control unit and
multifunction switch is malfunctioning. Multifunction switch power supply
and ground circuits.
Refer to AV- 4 6 6 , "
MULTIFUNC-
TION SWITCH : Diagnosis Proce-
dure".
 AV communication circuits be-
tween AV control unit and multi-
function switch.
U1300
U1248 AV COMM CIRCUIT
[U1300]
 DVD DECK CONN
[U1248]When either one of the following items is detected:
 DVD player power supply and ground circuits are mal-
functioning.
 AV communication circuits between BOSE amp. and
DVD player are malfunctioning.
 AV communication signal between AV control unit and
DVD player is malfunctioning. DVD player power supply and
ground circuits.
Refer to AV- 4 6 8 , "
DVD PLAYER :
Diagnosis Procedure".
 AV communication circuits be-
tween BOSE amp. and DVD player.
U1300
U124E AV COMM CIRCUIT
[U1300]
 AMP CONN [U124E]When either one of the following items is detected:
 BOSE amp. power supply and ground circuits are mal-
functioning.
 AV communication signal between AV control unit and
BOSE amp. is malfunctioning.BOSE amp. power supply and ground
circuits.
Refer to AV- 4 6 6 , "
BOSE AMP. : Diag-
nosis Procedure".
U1300
U1252 AV COMM CIRCUIT
[U1300]
 REAR-CAMERA LAN
CONN [U1252]When either one of the following items is detected:
 camera control unit power supply and ground circuits
are malfunctioning.
 AV communication signal between AV control unit and
camera control unit is malfunctioning.Camera control unit power supply
and ground circuits.
Refer to AV- 4 6 7 , "
CAMERA CON-
TROL UNIT : Diagnosis Procedure".
U1300
U125D AV COMM CIRCUIT
[U1300]
 DVD NAVI CONN
[U125D]NAVI control unit power supply and ground circuits are
malfunctioning.NAVI control unit power supply and
ground circuits.
Refer to AV- 4 6 4 , "
NAVI CONTROL
UNIT : Diagnosis Procedure".
U1300
U1248
U124E AV COMM CIRCUIT
[U1300]
 DVD DECK CONN
[U1248]
 AMP CONN [U124E]When either one of the following items is detected:
 AV communication circuits between NAVI control unit
and BOSE amp. are malfunctioning.
 AV communication signal between NAVI control unit
and BOSE amp. is malfunctioning.AV communication circuits between
NAVI control unit and BOSE amp.
U1300
U1248
U124E
U125D AV COMM CIRCUIT
[U1300]
 DVD DECK CONN
[U1248]
 AMP CONN [U124E]
 DVD NAVI CONN
[U125D]When either one of the following items is detected:
 AV communication circuits between camera control unit
and NAVI control unit are malfunctioning.
 AV communication signal between camera control unit
and NAVI control unit is malfunctioning.AV communication circuits between
camera control unit and NAVI control
unit.

AV-640
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003765976
RELATED TO BASIC OPERATION
RELATED TO HANDS FREE PHONE
 Check that the cellular phone is corresponding type (Bluetooth™ correspond) when the hands free related
malfunction vehicle is in service before performing a diagnosis,.
 There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a
corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone.
Simple check for Bluetooth™ communication
If cellular phone and NAVI control unit cannot be connected with Bluetooth™ communication, following proce-
dure allows the technician to judge which device has malfunction.
1. Turn on a cellular phone, not connecting Bluetooth
™ communication.
2. Start CONSULT-III, then start Windows
®.
3. Set CONSULT-III near a cellular phone.
4. When operated Bluetooth
™ registration by cellular phone, check
if CONSULT-III
* would be displayed on the device name.
(If other Bluetooth
™ device is located near cellular phone, a
name of the device would be displayed also.)
NOTE:
*:Displayed device name is “NISSAN- ”.
 If no device name is displayed, cellular phone is malfunction.
Repair the cellular phone first, then perform diagnosis.
 If CONSULT-III is displayed on device name, cellular phone is nor-
mal. Perform diagnosis as per the following table.
Symptoms Check items Possible malfunction location / Action to take
Multifunction switch and preset
switch operation does not work. All switches cannot be operated
 “MULTI AV” is displayed on system
selection screen when the CON-
SULT-III is started.Perform CONSULT-III self-diagnosis. Refer to AV- 4 3 4 ,
"CONSULT-III Function (MULTI AV)".
 All switches cannot be operated
 “MULTI AV” is not displayed on sys-
tem selection screen when the CON-
SULT-III is started.AV control unit power supply and ground circuit malfunc-
tion. Refer to AV- 4 6 4 , "
AV CONTROL UNIT : Diagnosis
Procedure".
Only specified switch cannot be operat-
ed.Multifunction switch or preset switch malfunction.
Replace multifunction switch or preset switch.
For multifunction switch, refer to AV- 6 5 9 , "
Removal and
Installation".
For preset switch, refer to AV- 6 6 0 , "
Removal and Instal-
lation".
Fuel economy display, vehicle set-
ting operation is abnormal.There is malfunction in the CONSULT-
III self-diagnosis result.Perform detected DTC diagnosis.
There is no malfunction in the self-diag-
nosis results.Ignition signal circuit malfunction.
Refer to AV- 4 6 4 , "
AV CONTROL UNIT : Diagnosis Pro-
cedure".
Guide sound is not heard.On the setting display select “system
sound (guide sound volume, etc.),” and
confirm that guide sound is ON.Voice guidance signal circuit malfunction.
JPNIA0441GB

AV
NORMAL OPERATING CONDITION
AV-645
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000003765977
NOTE:
For Navigation system operation information, refer to Navigation system Owner's Manual.
BASIC OPERATIONS
RELATED TO AUDIO
 The majority of the audio malfunctions are the result of outside causes (bad CD/cassette, electromagnetic
interference, etc.). Check the symptoms below to diagnose the malfunction.
 The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and oper-
ation of each piece of electrical equipment, and then determine the cause.
NOTE:
 CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be incor-
rectly mastered by the customer on a computer.
 Check if the CDs carry the Compact Disc Logo. If not, the disc is not mastered to the red book Compact Disc
Standard and may not play.
Symptom Possible cause Possible solution
No image is displayed.The brightness is at the lowest setting. Adjust the brightness of the display.
The system in the video mode. Push to change the mode.
The display is turned off.
Push <> to turn on the display.
The screen is too dim. The move-
ment is slow.The temperature in the interior of the vehicle is low. Wait until the interior of the vehicle has
warmed up.
Some pixels in the display are dark-
er or brighter than others.This condition is an inherent characteristic of liquid
crystal displays.This is not a malfunction.
Some menu items cannot be se-
lected.Some menu items become unavailable while the ve-
hicle is driven.Park the vehicle in a safe location, and
then operate the multi AV system.
Symptom Cause and Counter measure
Cannot play.Check if the CD was inserted correctly.
Check if the CD is scratched or dirty.
Check if there is condensation inside the player, and if there is, wait until the condensation is gone
(about 1 hour) before using the player.
If there is a temperature increase error, the player will play correctly after it returns to the normal
temperature.
If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music
CD files (CD-DA data) will be played.
Files with extensions other than “.MP3”, “.WMA”, “.mp3”, or “.wma” cannot be played. In addition,
the character codes and number of characters for folder names and file names should be in com-
pliance with the specifications.
Check if the disc or the file is generated in an irregular format, This may occur depending on the
variation or the setting of MP3/WMA writing applications or other text editing applications.
Check if the finalization process, such as session close and disc close, is done for the disc.
Check if the CD is protected by copyright.
Poor sound quality. Check if the CD is scratched or dirty.
It takes a relatively long time before
the music starts playing.If there are many folder or file levels on the MP3/WMA disc, some time may be required before
the music starts playing.
Music cuts off or skips.The writing software and hardware combination might not match, or the writing speed, writing
depth, writing width might not match the specifications. Try using the slowest writing speed.
Skipping with high bit rate files. Skipping may occur with large quantities if data such as for high bit rate data.