2008 NISSAN TEANA headrest

SE-132
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
FRONT SEAT
1. Headrest 2. Seatback trim 3. Seatback pad
4. Lumbar support lever knob 5. Snap pin 6. Seat cushion trim
7. Seat cushion pad 8. Seat belt buckle 9. Seat control unit
10. Seat cushion frame bracket 11. Front slide cover 12. Clip
13. Seat cushion duct B 14. Seat cushion duct A 15. Blower filter
16. Ventilation seat control unit 17. Ventilation motor 18. Seatback duct A
JMJIA1714GB

FRONT SEAT
SE-133
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
PASSENGER'S POWER SEAT
19. Seatback duct B 20. Seatback duct C 21. Clip
22. Seat slide and lifter switch knob 23. Reclining switch knob 24. Seat cushion outer finisher
25. Seat control switch 26. Seat cushion outer finisher inside 27. Seat harness clamp
28. Seat harness 29. Side air bag module 30. Seatback finisher
31. Side air bag module bracket 32. Seat cushion rear finisher 33. Seatback board
34. Seatback silencer 35. Seatback heater unit 36. Seat cushion heater unit
37. Seat slide inner cover 38. Lumbar support unit 39. Seat cushion inner finisher
40. Seat cushion inner finisher inside 41. TORX bolt 42. Seat frame assembly
43. TORX bolt 44. Seat slide outer cover 45. Rear slide cover
46. End cap 47. Reclining device outer cover 48. Reclining device inner cover
49. Headrest holder (locked) 50. Headrest holder (free)
Refer to GI-4, "
Components" for symbols in the figure.

FRONT SEAT
SE-135
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
Removal and InstallationINFOID:0000000003840024
REMOVAL
CAUTION:
 When removing and installing, use shop cloths to protect parts from damage.
 Before removal, turn ignition switch OFF, disconnect battery negative terminal, and then wait for at
least 3 minutes.
NOTE:
Confirming a position of connector before work.
1. Remove the headrest.
2. Slide the seat to the frontmost position.
3. Remove the rear outer mounting TORX bolt.
4. Remove the rear inner mounting TORX bolt.
5. Slide the seat to the rearmost position.
6. Remove the front slide cover.
 Open the front end of the front slide cover to release the
pawls.
 Slide the front slide cover forward to release the pawls.
7. Remove the front outer mounting TORX bolt.
8. Remove the front inner mounting TORX bolt.
9. Set seatback in a standing position.
10. Lift the seat to the uppermost position.
11. Disconnect harness connector under the seat and remove harness clamps.
12. Remove seat from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Before installation, turn ignition switch OFF, disconnect battery negative terminal, and then wait for
at least 3 minutes.
 Clamp the harness in position.
Disassembly and AssemblyINFOID:0000000003840025
SEATBACK
19. Clip 20. Seatback duct C 21. Front slide cover
22. Ottoman trim and pad 23. Front outer link cover 24. Rear outer link cover
25. Ottoman unit assembly 26. Front inner link cover 27. Rear inner link cover
28. Ottoman protector 29. Seat cushion inner finisher inside 30. Seat cushion inner finisher
31. Seat belt buckle 32. Seat cushion heater unit 33. Seat cushion pad
34. Seat cushion trim 35. Seatback pad 36. Seatback trim
37. Headrest 38. Seatback heater unit 39. Seatback silencer
40. Reclining device inner cover 41. Reclining device outer cover 42. Rear slide cover
43. End cap 44. Seat cushion outer finisher inside 45. Seat control switch
46. TORX bolt 47. TORX bolt 48. Seat frame assembly
49. Seat slide inner cover 50. Headrest holder (locked) 51. Headrest holder (free)
Refer to GI-4, "
Components" for symbols in the figure.
: Pawl
JMJIA1863ZZ

FRONT SEAT
SE-137
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
 Disconnect the seatback heater unit harness connector (A).
 Remove the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left).
 Remove the seatback trim and seatback pad from the seat frame assembly.
 Remove the hog rings to separate the seatback trim and seatback pad.
4. Remove the seatback silencer.
5. Remove the lumbar support unit. (With lumbar support model)
 Remove the screws.
 Remove the lumbar support unit while pulling the seatback spring.
6. Remove the reclining device outer and inner cover.
Remove the screws, and then remove reclining device outer and inner cover.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
SEAT CUSHION
Disassembly
1. Remove the seat cushion outer finisher.
a. Manual seat
 Remove the pawls, and then remove lifter lever knob finisher
(1).
 Remove the mounting screws, and remove lifter lever knob
(2).
JMJIA1868ZZ
PIIB4084J
: Pawl
JMJIA1869ZZ

SE-140
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
REAR SEAT
REAR SEAT
Exploded ViewINFOID:0000000003840026
HEADREST FIXED TYPE
HEADREST REMOVED AND INSTALLED TYPE
1. Seat belt hook 2. Bushing 3. Armrest bracket
4. Armrest assembly 5. Cup holder 6. Seat cushion hook
7. Seat cushion pad 8. Seat cushion trim 9. Seatback pad
10. Seatback trim
Refer to GI-4, "
Components" for symbols in the figure.
JMJIA1882GB

SE-142
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
REAR SEAT
Removal and Installation
INFOID:0000000003840027
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1. Remove the headrest.
2. Remove the seat cushion.
 Pull the lock lever (1) at the front bottom of the seat cushion
forward (1 for each side), and pull the seat cushion upward to
release the wire (2) from the seat cushion hook. Then pull the
seat cushion forward to remove.
 Remove the seat cushion from the vehicle.
3. Remove the seatback.
 Remove the bolts under seatback.
 Lift up seatback from underneath, and then remove seatback from seatback hook that is fixed to the
vehicle.
 Remove the seatback from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
Disassembly and AssemblyINFOID:0000000003840028
SEATBACK
Disassembly
1. Remove armrest assembly.
 Remove the pawls, and pull out the cup holder.
19. Seatback center pad 20. Seat cushion heater unit 21. Seatback heater unit
22. Seatback pad 23. Seatback trim 24. Seat belt hook
25. Headrest holder (locked) 26. Headrest holder (free) 27. Headrest side (long type)
28. Headrest side (normal type) 29. Headrest center (normal type) 30. Headrest center (long type)
31. Seatback duct C 32. Seatback duct B 33. Ventilation motor (seatback)
34. Blower filter 35. Seatback duct A 36. Ventilation seat control unit
Refer to GI-4, "
Components" for symbols in the figure.
JMJIA0251ZZ
: Pawl
JMJIA1936ZZ

REAR SEAT
SE-143
< ON-VEHICLE REPAIR >[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
 Remove the bolts (A), and then remove armrest retainer.
 Remove the armrest assembly.
2. Remove the seatback trim.
 Remove the screws, and then seat belt hook.
 Remove the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left).
 Remove the hog rings to separate the seatback trim and seatback pad.
Assembly
Assemble in the reverse order of disassembly.
SEAT CUSHION
Disassembly
Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
Assembly
Assemble in the reverse order of disassembly.
JMJIA1939ZZ
PIIB4084J