2008 NISSAN 350Z homelink

TABLE OF CONTENTS
Remote Keyless Entry System..........................2
Windshield Wiper/Washer Switch.......................2
Headlight and Turn Signal Control.......................3
RPM Shift Indicator (manual transmission only)................4
Steering Wheel Switches for Audio Control/Bluetooth

(if so equipped)..................................4
Cruise Control (if so equipped).........................5
Screw-in Recovery Hook.............................5
Auto Climate Control...............................6
Rear Floor Box...................................7
FM/AM/XM
* Radio with CD Changer (if so equipped)...........8
Clock Set/Adjustment...............................9
Trip Computer..................................10
Automatic Transmission (if so equipped)...................10
6-Speed Manual Transmission (if so equipped)...............11
Control Panel Display with Navigation System (if so equipped)......11
Traction Control System (TCS) Off Switch (if so equipped)........12
Front-Passenger Air Bag Status Light....................12
Tire Pressure Monitoring System (TPMS)..................12
Seat Belt Warning Light and Chime......................13
Front Seat Adjustments.............................13
Seatback Tilt Cancel Switch (Roadster only)................13
Power Windows.................................14
Secondary Rear Hatch Release........................14
Mirror Adjustment................................14
Soft Top Operation...............................15
Homelink
Universal Transceiver (if so equipped)..............16
Bluetooth
Hands-Free Phone System (if so equipped)..........17
Navigation System (if so equipped)......................19
This easy-to-use Quick Reference Guide is intended to help you more fully
appreciate some of the unique features and functions of your new vehicle.
However, it is not intended to replace your Owner’s Manual. The Owner’s
Manual contains more detailed information to help you better understand the
important safety warnings, features, operation, and maintenance of your
vehicle.

HOMELINK
UNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Your vehicle’s engine should be turned off while programming the
HomeLink
Transceiver.
To program your HomeLink
Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage door openers (manufactured after 1996) have “rolling code protec-
tion”. To program a garage door opener equipped with “rolling code protection”,
you will need to use a ladder to get up to the garage door opener motor to be able
to access the “smart or learn” program button.
PROGRAMMING YOUR HOMELINK
UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, press and hold the two
outer HomeLink
buttons (to
clear the memory) until the indi-
cator light blinks slowly (after 20
seconds) . Release both buttons.
2. Position the end of the hand-
held transmitter 1-3 inches
(26-76 mm) away from the
HomeLink
surface
3. Using both hands, simultaneously press and hold both the HomeLink
button you
want to program and the hand-held transmitter button.DO NOT release the
buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on the HomeLink
flashes, changing
from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds.
When the indicator light flashes rapidly, both buttons may be released. The rapidly
flashing light indicates successful programming. To activate the garage door or other
programmed device, press and hold the programmed HomeLink
button - releasing
when the device begins to activate.
5. If the indicator light on the HomeLink
blinks rapidly for two seconds and then turns
solid, HomeLink
has picked up a “rolling code” garage door opener signal. You will
need to proceed with the next steps to train the HomeLink
to complete the
programming which may require a ladder and another person for convenience.
6. Press and release the “smart” or “learn” program button located on the garage door
opener’s motor to activate the “training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire originates from under a light
lens, you will need to remove the lens to access the program button.
NOTE: Once you have pressed and released the program button on the garage
door opener’s motor and the “training light” is lit, you have 30 seconds in which to
perform step 7. Use the help of a second person for convenience to assist when
performing this step.
16

7. Quickly within 30 seconds of pressing and releasing the garage door opener
program button, firmly press and release the HomeLink
button you’ve just pro-
grammed. Press and release the HomeLink
button up to three times to complete the
training.
8. Your HomeLink
button should now be programmed. (To program the remaining
HomeLink
buttons for additional door or gate openers, follow steps 2-8 only) .
BLUETOOTH
HANDS-FREE PHONE SYSTEM (if so equipped)
With an overhead microphone and sound
transmitted through the audio system
speaker, the Bluetooth
Hands-Free Phone
System utilizes Bluetooth
wireless technol-
ogy and voice recognition to provide hands-
free cellular phone communication.
SYSTEM OPERATING TIPS
Close all windows. Surrounding noises
may interfere with system operation and
performance.
Press the
button on the steering wheel to activate voice recognition.
Wait for the tone before speaking.
Begin speaking a command within 5 seconds of the tone.
To go back to the previous command, say “Go back” or “Correction.”
To cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit,” or
press the
button.
To increase or decrease the volume of the voice prompts, push the VOL (volume) control
switch up or down on the steering wheel or turn theVOLknob on the audio system while
the system is responding.
Speak in a clear and natural voice without pausing between words.
If the Voice Recognition system does not recognize your voice commands, train the
system using the Speaker Adaptation Mode.
Some commands are not available while the vehicle is in motion.
The “Help” command can be used in any menu to hear a list of available commands.
For recommended phones and detailed instructions, please visit
www.nissanusa.com/bluetooth.
PAIRING YOUR PHONE
To use the hands-free feature, you need to set-up, or pair, the system to recognize your
compatible cellular phone(s) . 5 Bluetooth
-enabled phones can be paired. After set-up, the
system automatically connects with a paired phone when the ignition is in the ACC or ON
position, as long as the phone is on and in the vehicle.
17