2008 NISSAN 350Z change time

RPM SHIFT INDICATOR (manual transmission only)
The engine RPM shift indicator light (REV) is located in
the tachometer
. When driving, it indicates ‘shift
point’, or time to up-shift.
Set or deactivate the engine RPM shift point using
the trip computer display.
REV indicator will flash when the engine speed is
within 500 RPM of the set shift point.
REV light will illuminate when the engine speed
matches the set shift point RPM.
STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTH
(if so equipped)
Press theMODEbutton to turn the radio system on.
PressMODErepeatedly to change to the following
mode:
●Without XM
radio: AM, FM1, FM2, and CD or CD
changer.
●With XM
radio: AM, FM1, FM2, SAT1, SAT2 and
CD changer.
TheSEEKup or down
switch can be used to
perform the following:
●Push the SEEK
switch for less than 1.5 seconds to change the radio frequency.
●Push and hold the SEEK
switch for more than 1.5 seconds to seek the next or
previous broadcasting radio station.
●Push the SEEK
switch while playing a CD for less than 1.5 seconds to change
tracks on the CD.
●If the vehicle is equipped with a CD changer, push and hold the SEEK
switch for
more than 1.5 seconds to change between CDs.
●Push and hold the SEEK
switch for more than 1.5 seconds while playing an MP3
CD to change folders (if multiple folders exist) .
Push theVOLcontrol switch
up or down to increase or decrease the volume.
01
4

AUDIO BUTTON
To adjust the Bass, Treble, Fade, Balance, and Audio Pilot, press theAUDIObutton until
the desired mode appears in the display. Then press theTUNE/REW/FFbutton to
adjust to the desired level.
STATION AND CD SELECT BUTTONS
To store a station in a preset you must first select AM, FM1, FM2, SAT1 or SAT2 radio
band by pressing theRADIObutton and tune to the desired FM, AM or XM
station.
Then press and hold the desired station select button for at least 2 seconds. When
the preset indicator illuminates, a beep will sound, indicating memorization is com-
plete. To retrieve a previously set station, select the radio band where the preset was
set, then press the corresponding station select button.
While playing a CD, to select a different CD loaded into the CD changer press one of
the CD select buttons (1-6).
DISP BUTTON
Pressing theDISPbutton will display additional information (for example: Title, Artist
name) .
MP3 PLAYBACK (if so equipped)
In addition to playing audio CDs, the audio system can play MP3 files recorded on
CD-ROM, CD-R, and CD-RW discs. Each disc can have a maximum of 8 folder levels
and 255 folders. A total of 512 MP3 files can be played back. During MP3 playback,
some recorded ID3 tag information can be displayed by pressing theDISPbutton.
Use theTUNE/REW/FFbutton to navigate the MP3 folders.
SEEK/TRACK BUTTON
To scan quickly through each broadcasting station, press theSEEK/TRACKbutton.
To skip from one track to another on a CD, press theSEEK/TRACKbutton. Each
time the button is pressed, the CD will advance or skip back one track.
*XM
Satellite Radio is only available on vehicles equipped with optional XM
satellite
subscription service.
CLOCK SET/ADJUSTMENT
NAVIGATION SYSTEM ONLY (if so equipped)
Press theSETTINGbutton, then select the “Clock”
key using the joystick and press theENTERbutton
to access the following clock settings:
On-screen Clock – When this item is turned to
ON, a clock is always displayed in the upper
right corner of the screen. The clock is automati-
cally adjusted by the GPS system.
Clock Format – Choose either the 12-hour
clock display or the 24-hour clock display.
Offset Adjust – Adjust the time by increasing or decreasing per minute.
Daylight Saving Time – Turn this item to ON for daylight savings time application.
Time Zone – Choose the time zone.
9

FM/AM/XM
RADIO WITH CD CHANGER (if so equipped)
Press and hold theRPTbutton for approximately 2 seconds until the clock display starts
to flash.
Press theSEEK/TRACKbutton to adjust the hours.
Press theTUNE/REW/FFbutton to adjust the minutes.
Press theRPTbutton again to exit the clock set mode.
TRIP COMPUTER
The trip computer may be used to check items such as speed,
outside air temperature, distance to empty (fuel) , average mile-
age and speed, elapsed time and distance traveled. Additionally,
it can function as a stopwatch or be used to operate the RPM
shift feature (REV) (Manual transmission only) .
The twin trip odometer records the distance of individual
trips.
Press the button
to change the display as follows: Trip
A→Trip B→Trip A.
Press and hold the button for more than 1 second to reset
the trip odometer to zero.
TO OPERATE THE TRIP COMPUTER
Turn the ignition switch ON. Then press the side of the buttons.
Press the button
toward the left to scroll through each
mode.
Press the button
toward the left to reset or adjust the various mode selections.
AUTOMATIC TRANSMISSION (if so equipped)
MANUAL SHIFT MODE
When the shift selector lever is shifted from D (Drive)
to the manual shift gate, the transmission enters the
manual shift mode.
In the manual shift mode, shift range is displayed on
the position indicator in the meter.
WHEN SHIFTING UP
Move the shift selector lever to the + (up) side. (Shifts to higher range.)
10

PAIRING PROCEDURE
NOTE: The vehicle must be stationary when pairing the phone.
1. Press the
button on the steering wheel and wait for the tone.
2. Say “Setup.”
3. Wait for the tone, then say “Pair phone.”
4. Wait for the tone, then say “New phone.”
5. Initiate pairing from the phone.
The pairing procedure varies according to each cellular phone model. For detailed
pairing instructions and a list of compatible phones, please visit
www.nissanusa.com/bluetooth.
When prompted for a PASSKEY code, enter “1234” from the handset. (The PASS-
KEY code is assigned by NISSAN and cannot be changed.)
6. Say a name for the phone when the system asks you to provide one. You can give the
phone a name of your choice.
7. Say a number between 1 and 5 when the system asks you for a priority level. The
priority level determines which phone interacts with the system when two or more
paired phones are active in the vehicle at the same time. Choose 1 if this is the only
phone or the primary phone.
8. Say “Yes” or “No” when the system asks if you would like to select a custom ring tone.
Follow the instructions provided by the system to choose a ring tone.
SETTING UP YOUR PHONEBOOK – ADDING NEW ENTRIES
Each paired phone has its own dedicated phone book. Each phone book can store up to 40
names. Each name can have up to 4 locations/numbers: Home, Office, Mobile, and Other.
NOTE: The vehicle must be stationary when adding new entries.
1. Press the
button and wait for the tone.
2. Say “Phone book.”
3. Wait for the tone, then say “New entry.”
4. When prompted, say the name for the new entry. For example, say “Michelle.” If the
name is too short or too long, or if it sounds too much like a name that is already
stored in the phone book, the system tells you and prompts you to say a name again.
Choose a new name.
5. Say “Yes” or “No” when the system asks you to confirm the name is correct.
6. Say a location (“Home,” “Office,” “Mobile” or “Other”) when the system asks you to
provide one. The system acknowledges the location.
By Voice command - When prompted, say a phone number for the location. For
example, say “five five five one two one two.” The system repeats the number and
prompts you for the next command.
By Bluetooth
transfer - Say “Transfer entry.” The system acknowledges the com-
mand and asks you to initiate the transfer from the phone handset. The new contact
phone number will be transferred from the cellular phone via the Bluetooth
commu-
nication link. The transfer procedure varies according to each cellular phone. See the
cellular phone owner’s manual for details.
18