Page 170 of 458

3-44 Instruments and controls
3
NOTE●To ensure a clear rearward view, the wiper performs a
number of continuous operations either when the switch is
moved to the “INT” position or when the gearshift lever
(M/T) or the selector lever (A/T) is moved to the “R”
position while the switch is in the “INT” position.
Following this continuous operation, the wiper will auto-
matically switch to intermittent operation.
●It is possible to spray washer fluid without activating the
wiper. To do so, hold the knob at the end of the lever in the
“ ” position and turn the ignition switch to the “ON” or
“ACC” position.
●It is possible to activate the following functions. For fur-
ther information, we recommend you to consult a MIT-
SUBISHI MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display Station
(MDS), the functions can be adjusted on the screen. For
details, refer to a separate operation manual.
• Adjustment of the interval for intermittent operation
• Causing the wipers to switch to continuous operation
when the knob at the end of the lever is turned to the
“INT” position twice within approximately 1 second
• Changing intermittent wiper operation to continuous
wiper operation
• Causing the wiper never to operate when washer fluid is
sprayed
Precautions to observe when using wipers and
washers
E00507600014
●If the moving wipers become blocked by ice or other
deposits on the glass, the motor may burn out even if the
wiper switch is turned to OFF. If obstruction occurs, park
your vehicle in a safe place, turn off the ignition, and
clean the deposits from the glass so that the wipers operate
smoothly.
●Do not use the wipers when the glass is dry. They may
scratch the glass surface or the blades may prematurely
wear out.
●Before using the wipers in cold weather, check that the
wiper blades are not frozen onto the glass. The motor may
burn out if the wipers are used with the blades frozen onto
the glass.
●Avoid using the washer continuously for more than
20 seconds. Do not operate the washer when the fluid res-
ervoir is empty.
Otherwise, the motor may burn out.
●Periodically check the level of washer fluid in the reser-
voir and refill if required.
During cold weather, add a recommended washer solution
that will not freeze in the washer reservoir. Failure to do
so could result in loss of washer function and frost dam-
age to the system components.
BK-XP08E1ENUK.en-uk.book Page 44 Monday, August 13, 2007 2:20 PM
Page 356 of 458

7-8 Vehicle care
7
Wiper blades
E00901700017
Use a soft cloth and glass cleaner to remove grease, dead
insects, etc., from the wiper blades. Replace the wiper blades
when they no longer wipe properly. (Refer to page 8-29.)Cleaning the sunroof*
E00901800018
Clean the inside of the sunroof with a soft cloth. Hard deposits
should be wiped away with a cloth dipped in warm, neutral
detergent solution. Wipe away the solution with a sponge
dipped in fresh water.NOTE●The surface treatment on the inside of the glass may be
removed if hard cloth or organic solvent (benzine, thinner,
etc.) is used.
Engine compartment
E00902100265
Clean the engine compartment at the beginning and end of
winter. Pay particular attention to flanges, crevices and periph-
eral parts where dust containing road chemicals and other cor-
rosive materials might collect.
If salt and other chemicals are used on the roads in your area,
clean the engine compartment at least every three months.
Never spray or splash water on the electrical components in the
engine compartment, as this may cause damage.
Do not bring the nearby parts, the plastic parts and so on into
contact with sulphuric acid (battery electrolyte) which may
crack, stain or discolour them.
If they are in contact, wipe off with soft cloth, chamois or the
like and an aqueous solution of neutral detergent then immedi-
ately rinse the affected parts with plenty of water.
BK-XP08E1ENUK.en-uk.book Page 8 Monday, August 13, 2007 2:20 PM
Page 357 of 458

8
Maintenance
Service precautions . . . . . . . . . . . . . . . . . . . . . . . .8- 2
Catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . .8- 3
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 4
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 7
Engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 10
Automatic transmission fluid* . . . . . . . . . . . . . . . .8- 13
Washer fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 14
Brake fluid/Clutch fluid* . . . . . . . . . . . . . . . . . . . .8- 14
Power steering fluid . . . . . . . . . . . . . . . . . . . . . . . .8- 15
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 16
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 21
Clutch pedal free play* . . . . . . . . . . . . . . . . . . . . .8- 27
Brake pedal free play . . . . . . . . . . . . . . . . . . . . . . .8- 28
Parking brake lever stroke . . . . . . . . . . . . . . . . . . .8- 28
Wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 29
General maintenance . . . . . . . . . . . . . . . . . . . . . . .8- 31
For cold and snow weather . . . . . . . . . . . . . . . . . .8- 32
Fuse links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 33
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8- 33
Replacement of lamp bulbs . . . . . . . . . . . . . . . . . .8- 43
BK-XP08E1ENUK.en-uk.book Page 1 Monday, August 13, 2007 2:20 PM
Page 385 of 458
Maintenance
8-29
8 Wiper blades
E01002600398
If the blades are frozen to the windscreen or rear window, do
not operate the wipers until the ice has melted and the blades
are freed, otherwise the wiper motor may be damaged.Wiper blade rubber replacementWindscreen wiper blades1. Lift the wiper arm off the windscreen.
2. Pull the wiper blade (A) downward to remove it com-
pletely from the wiper arm (B).NOTE●Do not allow the wiper arm to fall onto the windscreen; it
could damage the glass.3. Attach retainers (C) to a new wiper blade.
Refer to the illustration to ensure that the retainers are cor-
rectly aligned as you insert them into the groove.
NOTE●If retainers are not supplied with the new wiper blade, use
the retainers from the old blade.
4. Position the wiper blade stopper (D) as shown and insert
the blade into the wiper arm (B) from the lower end of the
arm.
BK-XP08E1ENUK.en-uk.book Page 29 Monday, August 13, 2007 2:20 PM
Page 386 of 458
8-30 Maintenance
8
5. Slide the wiper blade (A) until it contacts the end of the
wiper arm (B).NOTE●After installation, gently pull up and down on the wiper
blade to make sure the stopper is securely engaged.
Rear window wiper blades1. Lift the wiper arm off the window glass.
2. Pull the wiper blade downward to disengage it from the
stopper (A) at the end of the wiper arm. Pull the wiper
blade further to remove it.
3. Slide a new wiper blade through the hook (B) on the wiper
arm.NOTE●Do not allow the wiper arm to fall onto the window glass;
it could damage the glass.
BK-XP08E1ENUK.en-uk.book Page 30 Monday, August 13, 2007 2:20 PM
Page 448 of 458
Alphabetical index
8Wiper
Rear window 3-43
Windscreen 3-41
Wiper blades 8-29BK-XP08E1ENUK.en-uk.book Page 8 Monday, August 13, 2007 2:20 PM