2008 MITSUBISHI GRANDIS buttons

3-20 Instruments and controls
3
Manual modeThe manual mode is also available in case the “Automatic
mode” shows the incorrect time when the adjacent local RDS
stations are located in a different time zone. Refer to “Radio
data system (RDS)” on page 5-29.
Set the time by pressing the various buttons as described
below.
Outside temperature
E00503900019
This value shows the outside temperature of the vehicle.
If the outside air temperature drops below approx. 3 °C, the
alarm sounds and the outside air temperature figure flashes for
about 10 seconds.
H- To adjust the hour
M- To adjust the minutes
SET- To reset the minutes to zero
10:30-11:29...Changes to 11:00
11:30-12:29...Changes to 12:00
CAUTION
!●There is a danger the road might be icy, even when
the outside air temperature figure is not flashed, so
please take care when driving.
BK-XP08E1ENUK.en-uk.book Page 20 Monday, August 13, 2007 2:20 PM

For pleasant driving
5-23
5
Volume and tone control panel
E00708600651
1- PWR (On-Off) switch
2- VOL (Volume control) knob
3- AUDIO button
4- Memory select buttons
5- Audio adjust button
6- Display
BK-XP08E1ENUK.en-uk.book Page 23 Monday, August 13, 2007 2:20 PM

For pleasant driving
5-25
5
To enter audio tone settings into the memoryIt is possible to enter the audio adjustment condition (BASS,
TRE, FADE, BAL) into the memory.
1. Make the desired adjustments in the audio adjust mode.
Refer to “To adjust the tone” on page 5-24.
2. In the audio adjust mode, press and hold one of the mem-
ory select buttons (4) [1-6]. When you hear a bleep, the
memorization is complete. The display will show the but-
ton number [SOUND1-SOUND6] for which the settings
were memorized.
3. In future, when you gently press the memory select button
in the audio adjust mode, the audio adjustment condition
memorized for that button will take effect.
BK-XP08E1ENUK.en-uk.book Page 25 Monday, August 13, 2007 2:20 PM

5-26 For pleasant driving
5
Radio control panel and display
E00708900713
1- AM/FM (FM/MW/LW selection) button
2- TUNE/SEEK (Down-step/Down-seek) button
3- TUNE/SEEK (Up-step/Up-seek) button
4- Memory select buttons
5- PWR (On-Off) switch
6- FM (FM1/FM2/FM3) indicators
7- ST (Stereo) indicator
8- Preset memory number display
9- Frequency display window
BK-XP08E1ENUK.en-uk.book Page 26 Monday, August 13, 2007 2:20 PM

For pleasant driving
5-27
5
To listen to the radio
E00709000678
1. Press the PWR switch (5) to turn the audio system on and
off. The system turns on in the last mode used.
2. Press the AM/FM button (1) to select the desired band.
3. Press the TUNE/SEEK button (2 or 3) to turn to a station,
or press one of the memory select buttons (4) to recall a
station memorised for that button.To tune the radio
E00709100565
Automatic tuning
After keeping the TUNE/SEEK button (2 or 3) depressed until
it beeps, release the button, and the selected station reception
will start.
Manual tuning
The frequency changes every time the TUNE/SEEK button
(2 or 3) is pressed. Press the button to select the desired station.
To enter frequencies into the memory
E00716100785
Manual setting
You can assign to the memory select buttons (4) a maximum of
18 stations in the FM band (6 FM1, 6 FM2 and 6 FM3 stations)
and 6 stations each in the MW and LW band. (Stations already
assigned to the memory select buttons are replaced by any
newly assigned stations.)
BK-XP08E1ENUK.en-uk.book Page 27 Monday, August 13, 2007 2:20 PM

5-28 For pleasant driving
5
Follow the steps described below.
1. Press either the TUNE/SEEK button (2 or 3) to tune the
frequency to be entered in the memory.
2. Press one of the memory select buttons (4) for 2 seconds
or longer. The sound will be momentarily interrupted
while the frequency is being entered into the memory.
The number of the button corresponding to the entry in the
memory and the frequency are displayed.
3. The preset memory setting is retrieved by pressing the
button and then releasing it within 2 seconds.
Automatic setting
With the method, all manually set stations in the band currently
selected for reception are replaced with stations in the same
band that are automatically selected in order of signal strength.
The radio automatically selects 6 stations in the FM band (FM3
station only) and 6 stations each in the MW and LW band.
Follow the steps described below.
1. With the radio mode selected, hold down the AM/FM but-
ton (1) for 2 seconds or longer. The 6 stations with the
best signal strength will automatically be assigned to the
memory select buttons (4), with the lowest-frequency sta-
tion being assigned to the lowest-number button.
2. When you subsequently press a memory select button to
select a channel number, the radio will begin receiving the
station assigned to that number.NOTE●If you press the AM/FM button (1) for 2 seconds or longer
while tuning in the FM1 or FM2 band, the radio will auto-
matically switch to the FM3 band, where the automatic
seeking/storing will be activated.
BK-XP08E1ENUK.en-uk.book Page 28 Monday, August 13, 2007 2:20 PM

For pleasant driving
5-29
5
Radio data system (RDS)
E00709200247
1- AM/FM (FM/MW/LW selection) button
2- Menu button
3- Memory select buttons
4- PWR (On-Off) switch
5- TUNE/SEEK (Down-step/Down-seek) button
6- TUNE/SEEK (Up-step/Up-seek) button
7- TP (Traffic program) button
8- PTY (Program type) button
9- AF (Alternative frequencies) indicator
10- RDS (Radio data system) indicator
11- REG (Regional program) indicator
12- TP (Traffic program identification) indicator
13- PTY (Program type) indicator
14- CT (Clock time) indicator
15- Frequency display window
BK-XP08E1ENUK.en-uk.book Page 29 Monday, August 13, 2007 2:20 PM

5-32 For pleasant driving
5
NOTE●If the TUNE/SEEK button (5 or 6) is pressed for more
than 1 second, the radio will try to find out another broad-
cast of the same program type as currently selected.
●If no station is found with your desired PTY, the display
will show “EMPTY” for about 5 seconds and the radio
will return to the previous station.How to enter PTYs in the memory
E00721400122
As many as 6 PTYs can be entered in the memory.
Follow the steps described below.
1. Press either the TUNE/SEEK button (5 or 6) to tune the
PTY to be entered in the memory.
2. Press one of the memory select buttons (3) for 2 seconds
or longer. The sound will be momentarily interrupted
while the PTY is being entered into the memory. The
number of the button corresponding to the entry into the
memory and the PTY are displayed.
3. The preset memory setting is retrieved by pressing the
button and then releasing it within about 2 seconds.
To change the language of PTY display
E00721500181
You can select your favourite language among English, French,
German, Swedish, Spanish and Italian.
1. Press the “MENU” button (A) to select the language of
PTY display mode.
Refer to “Function setup mode” on page 5-35.
2. Press the audio adjust button (B) to select a language.NOTE●After selecting a mode, you can leave the function setup
mode by taking either of the following steps:
• Press the “MENU” button for at least 2 seconds.
• Make no entry for 7 seconds.
BK-XP08E1ENUK.en-uk.book Page 32 Monday, August 13, 2007 2:20 PM