2008 MITSUBISHI GRANDIS reset

Instruments and controls
3-27
3
●Automatic reset mode
When 4 hours have passed after the ignition switch is
turned to the “OFF” or “ACC” position, the display is
automatically reset. It then shows “---”.
●Manual reset mode
If you reset the display at the time when you want to start
the measurements, average speed from that point of time
can be displayed.
To reset the display, push the “DISP” button for about
5 seconds or more.NOTE●While the ignition switch is in the “ON” position, the
automatic reset mode is permanently selected. If you wish
to make continuous measurements, select the manual
mode.
Display brightness adjustment
E00509600018
1. Press and hold down button (A), then press the “H” button
(B) within 1 second. A buzzer will sound, and the system
will allow adjustment of the display brightness.
BK-XP08E1ENUK.en-uk.book Page 27 Monday, August 13, 2007 2:20 PM

Starting and driving
4-47
4
2. Pull the lever (B) down while driving at the desired speed.NOTE●If the main switch is on when the ignition switch is turned
to “LOCK” or “ACC” position, auto-speed control will be
on automatically the next time you start the engine. The
CRUISE indication lamp will also come on. You will need
to reset the speed however, if you want to use auto-speed
control.
●If the battery voltage is insufficient, the memory data for
the main switch will be erased.
As a result, the CRUISE indication lamp may not come on
when you restart the engine.
If this happens, push in the main switch once again to acti-
vate the system.
●On diesel-powered vehicles, it is not possible to set the
vehicle speed while driving in 1st gear.
To increase the set speed
E00609400323
There are 2 ways to increase the set speed.Auto-speed control leverPull the auto-speed control lever up and hold it while driving at
the set speed, and you will increase gradually.
When you reach your desired speed, release the switch. Your
cruising speed is now set.
To increase your speed in small amounts, press the auto-speed
control lever up for less than 1 second and release it. Each time
you press the lever up, your vehicle will go about 1.6 km/h
(1 mph) faster.
BK-XP08E1ENUK.en-uk.book Page 47 Monday, August 13, 2007 2:20 PM

5-26 For pleasant driving
5
Radio control panel and display
E00708900713
1- AM/FM (FM/MW/LW selection) button
2- TUNE/SEEK (Down-step/Down-seek) button
3- TUNE/SEEK (Up-step/Up-seek) button
4- Memory select buttons
5- PWR (On-Off) switch
6- FM (FM1/FM2/FM3) indicators
7- ST (Stereo) indicator
8- Preset memory number display
9- Frequency display window
BK-XP08E1ENUK.en-uk.book Page 26 Monday, August 13, 2007 2:20 PM

5-28 For pleasant driving
5
Follow the steps described below.
1. Press either the TUNE/SEEK button (2 or 3) to tune the
frequency to be entered in the memory.
2. Press one of the memory select buttons (4) for 2 seconds
or longer. The sound will be momentarily interrupted
while the frequency is being entered into the memory.
The number of the button corresponding to the entry in the
memory and the frequency are displayed.
3. The preset memory setting is retrieved by pressing the
button and then releasing it within 2 seconds.
Automatic setting
With the method, all manually set stations in the band currently
selected for reception are replaced with stations in the same
band that are automatically selected in order of signal strength.
The radio automatically selects 6 stations in the FM band (FM3
station only) and 6 stations each in the MW and LW band.
Follow the steps described below.
1. With the radio mode selected, hold down the AM/FM but-
ton (1) for 2 seconds or longer. The 6 stations with the
best signal strength will automatically be assigned to the
memory select buttons (4), with the lowest-frequency sta-
tion being assigned to the lowest-number button.
2. When you subsequently press a memory select button to
select a channel number, the radio will begin receiving the
station assigned to that number.NOTE●If you press the AM/FM button (1) for 2 seconds or longer
while tuning in the FM1 or FM2 band, the radio will auto-
matically switch to the FM3 band, where the automatic
seeking/storing will be activated.
BK-XP08E1ENUK.en-uk.book Page 28 Monday, August 13, 2007 2:20 PM

5-30 For pleasant driving
5
RDS uses PI (program identification) signal and AF (alterna-
tive frequency) list transmitted in addition to the normal FM
broadcasting programs, and picks up the FM stations that are
transmitting the same program from the EON (enhanced other
network) and automatically tunes to the station with the strong-
est signal intensity.
Therefore, you can continue listening to one program in, for
example, a long distance driving without retuning to the other
station transmitting the same program when you are leaving
the service area of the currently receiving station.
The RDS radio also features the limited reception of the pro-
gram types, the break-in reception of the traffic announcement
and emergency broadcast, and the limited/unlimited reception
of the regional programs.AF (Alternative Frequencies) function
E00720900016
The AF function finds a station broadcasting the same program
and selects the station with the strongest signal of AF lists.
The AF function is turned on (with the AF indicator (9) shown
on the display) at all times unless you manually switch it off.
The AF function can be turned ON and OFF.
Refer to “Function setup mode” on page 5-35.CT (Clock Time) function
E00721000014
The clock can be set automatically by using the signal from the
local RDS stations. Refer to “Digital clock” on page 3-17.
REG (Regional) function
E00721100015
REG function limits to receive the stations broadcasting
regional programs.
Regional programming and regional networks are organized
differently depending on the country or area (they may be
changed according to the hour, state, or broadcast area), so if
you don’t want to receive the regional programs automatically,
you can set up REG ON not to receive regional programs.
The REG function can be turned ON and OFF.
Refer to “Function setup mode” on page 5-35.PI (Program Identification) search function
E00721200016
When travelling long distance and the recalled preset station is
weak, the radio searches another frequency broadcasting the
same programming with the same PI code in AF list.
If there are no frequencies broadcasting the same program-
ming, the radio searches a frequency broadcasting the regional
programming. The radio succeeds in searching the regional
programming, then the display shows the REG indicator (11).
If the radio does not succeed in searching the regional pro-
gramming, the radio returns to the recalled preset station.PTY (Program type)
E00721300192
RDS broadcasts are classified according to program type
(PTY) as follows. Use the TUNE/SEEK button (5 or 6) to
select your desired PTY.
BK-XP08E1ENUK.en-uk.book Page 30 Monday, August 13, 2007 2:20 PM

5-32 For pleasant driving
5
NOTE●If the TUNE/SEEK button (5 or 6) is pressed for more
than 1 second, the radio will try to find out another broad-
cast of the same program type as currently selected.
●If no station is found with your desired PTY, the display
will show “EMPTY” for about 5 seconds and the radio
will return to the previous station.How to enter PTYs in the memory
E00721400122
As many as 6 PTYs can be entered in the memory.
Follow the steps described below.
1. Press either the TUNE/SEEK button (5 or 6) to tune the
PTY to be entered in the memory.
2. Press one of the memory select buttons (3) for 2 seconds
or longer. The sound will be momentarily interrupted
while the PTY is being entered into the memory. The
number of the button corresponding to the entry into the
memory and the PTY are displayed.
3. The preset memory setting is retrieved by pressing the
button and then releasing it within about 2 seconds.
To change the language of PTY display
E00721500181
You can select your favourite language among English, French,
German, Swedish, Spanish and Italian.
1. Press the “MENU” button (A) to select the language of
PTY display mode.
Refer to “Function setup mode” on page 5-35.
2. Press the audio adjust button (B) to select a language.NOTE●After selecting a mode, you can leave the function setup
mode by taking either of the following steps:
• Press the “MENU” button for at least 2 seconds.
• Make no entry for 7 seconds.
BK-XP08E1ENUK.en-uk.book Page 32 Monday, August 13, 2007 2:20 PM