2008 MERCEDES-BENZ SL65AMG Owner's Manual

416 Practical hints
Replacing wiper blades
Vehicles with KEYLESS-GO*
Turn off the engine (page 64).
With the driver’s door closed, the
starter switch is now in position1.
Turn combination switch to wiper
settingII (
page 58).
With wiper arms in the vertical position,
open the driver’s door.
The starter switch is set to position0,
same as SmartKey removed from
starter switch.
Turn combination switch to wiper
setting0 (
page 58).
Removing wiper blades
Fold the wiper arm forward until it
snaps into place.
Turn wiper blade at a right angle to the
wiper arm.
Slide the wiper blade sideways out of
the retainer.
Installing wiper blades
Slide the wiper blade onto the wiper
arm in opposite direction of arrow.
Rotate the wiper blade into a position
parallel to the wiper arm.
Fold the wiper arm backward to rest on
the windshield. Make sure you hold on
to the wiper when folding the wiper arm
back.
!Do not pull on the wiper blade inserts. They
could tear.
!Make sure the wiper blades are properly
installed. Improperly installed wiper blades may
cause windshield damage.

417 Practical hints
Flat tire
Flat tire
Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.
Turn on the hazard warning flashers.
Turn the steering wheel so that the
front wheels are in a straight ahead
position.
Set the parking brake (page 63).
Move the gear selector lever to
position P.
Turn off the engine (page 64).
Have any passenger exit the vehicle at
a safe distance from the roadway.
Vehicles with Smartkey: Remove the
SmartKey from the starter switch.
Vehicles with KEYLESS-GO*: Open the
driver’s door (this puts the starter
switch in position 0, same as with the
SmartKey removed from the starter
switch). The driver’s door then can be
closed again.Mounting the spare wheel
iOpen door only when conditions are safe to
do so.
Warning!G
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a mounted spare
wheel. Adapt your driving style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted, en-
sure proper tire inflation pressure and do
not exceed vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the spare wheel
replaced with a regular road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a spare
wheel is mounted.

418 Practical hints
Flat tire
Preparing the vehicle
Prepare the vehicle as described
(
page 417).
Turn spare wheel bracket counter-
clockwise to loosen.
Take the spare wheel out of the trunk
(
page 401).
Removing tensioning straps
(vehicles with 19" spare wheel only)
A 19" spare wheel has two tensioning
straps on it that must both be removed be-
fore mounting the spare wheel.1Buckle
2Clip
Press on both clips 2 simultaneously
to release buckle 1.Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizeable
objects.
When changing wheel on a level
surface:
Place one wheel chock or other
sizeable object in front of and
another wheel chock or sizeable
object behind the wheel that is
diagonally opposite to the wheel
being changed.
Always try lifting the vehicle using the
jack on a level surface. However,
should circumstances require you to do
so on a hill, place a wheel chock or
other sizeable object and the other
wheel chock or sizeable object as
follows:
Place wheel chocks or other size-
able objects on the downhill side
blocking both wheels of the axle not
being worked on.
iThe tensioning straps are shown in red for
illustration purposes. The tensioning straps on
the spare wheel of your vehicle are black.iKeep the tensioning straps in a safe place.
You will need them to store the spare wheel in
the trunk after use (
page 402).

419 Practical hints
Flat tire
Take the vehicle tool kit and the jack
out of the storage compartment under
the trunk floor (
page 400).
On wheel to be changed, loosen but do
not yet remove the wheel bolts
(approximately one full turn with
wrench).
The jack support tubes are located behind
the front wheel housings and in front of the
rear wheel housings.
Warning!G
The jack is designed exclusively for jacking
up the vehicle at the jack tubes built into
both sides of the vehicle. To help avoid
personal injury, use the jack only to lift the
vehicle during a wheel change. Never get
beneath the vehicle while it is supported by
the jack. Keep hands and feet away from the
area under the lifted vehicle. Always firmly
set parking brake and block wheels before
raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Be sure that the jack arm is
fully inserted in the jack tube. Always lower
the vehicle onto sufficient capacity jack-
stands before working under the vehicle.
Warning!G
When turning the wheel wrench to loosen
the wheel bolts, make sure you position
hands on the wrench in such a way that you
avoid injury to yourself, such as scraping
your hands against the wheel. Make sure
turning the wheel wrench will not scratch or
damage the wheel rim.


420 Practical hints
Flat tire
1Jack support tube cover (except
SL 55 AMG, SL 65 AMG and vehicles
with Sport Package*)
Open cover1 by pressing at point
indicated by arrow.
Remove cover1, taking care not to
damage the locking tabs.2Jack support tube cover (SL 55 AMG,
SL 65 AMG and vehicles with
Sport Package* only)
Insert a flat blade screwdriver in the
opening of cover2 and pry it out.
Remove cover2, taking care not to
damage the locking tabs.3Crank
4Jack arm
5Jack support tube hole
Insert jack arm4 fully into tube
hole5 up to the stop.
Warning!G
Insert the jack arm fully into the jack
support tube hole up to the stop. Otherwise
the vehicle may fall from the jack and cause
personal injury or damage to the vehicle.


421 Practical hints
Flat tire
Keeping jack in this position, turn
crank3 clockwise until the jack base
meets the ground. Make sure the jack
is vertical (plumb line).
Continue to turn the crank until the tire
is a maximum of 1.2 in (3 cm) from the
ground.Removing the wheel
1Alignment bolt
Unscrew upper-most wheel bolt and
remove.
Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.
Remove the remaining bolts.
Remove the wheel.Mounting the new wheel
Clean contact surfaces of wheel and
wheel hub.
Guide the spare wheel onto the align-
ment bolt and push it on.
Insert wheel bolts and tighten them
slightly.
!Do not place wheel bolts in sand or dirt. This
could result in damage to the bolt and wheel hub
threads.
Warning!G
Inflate spare wheel tire only after the wheel
is properly mounted.
Inflate the spare wheel tire using the
electric pump (
page 422) before lowering
the vehicle.

422 Practical hints
Flat tire
Unscrew the alignment bolt, install last
wheel bolt and tighten slightly.
Inflating the spare tire (collapsible tire)
Take the electric air pump out of the
trunk (
page 400).1Flap
2Air pump switch
3Electrical plug
4Air hose with pressure gauge and vent
screw
5Union nut
Open flap 1 on air pump.
Pull out electrical plug 3 and air hose
with the pressure gauge 4.
Remove the valve cap from the tire
valve.
Screw union nut 5 onto the tire valve.
Warning!G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident. Be
sure to use the correct wheel bolts.
Warning!G
Only use genuine Mercedes-Benz wheel
bolts. They are identified by the Mercedes
star. Other wheel bolts may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
fall off the jack.
!Do not lower the vehicle before inflating the
spare wheel tire. Otherwise the rim may be dam-
aged.
Warning!G
Observe instructions on air pump label.

423 Practical hints
Flat tire
Insert electrical plug 3 into vehicle
cigarette lighter socket (
page 244)
or the power outlet in the trunk
(
page 246).
Turn the SmartKey in the starter switch
to position1.
or
Press the KEYLESS-GO* start/stop
button on the gear selector lever once
without depressing the brake pedal.
PressI on the electric air pump
switch2.
The electric air pump should now
switch on and inflate the tire.
Inflate the spare tire:

SL 550 to 36 psi (2.5 bar)

SL 600, SL 55 AMG, SL 55 AMG
(Performance Package*), and
SL 65 AMG to 51 psi (3.5 bar)
This takes about 5 minutes.
Air hose4 and union nut5 can be-
come hot during inflation. Exercise
proper caution to avoid burning your-
self when using the equipment.
Press0 on the electric air pump
switch2.
Turn the SmartKey in the starter switch
to position0.
or
Press KEYLESS-GO* start/stop button
on the gear selector lever twice without
depressing the brake pedal.
The electric air pump should now be
switched off.
If the spare tire inflation pressure is
above the recommended tire inflation
pressure for the respective collapsible
tire (
page 453), release excess spare
tire inflation pressure using the vent
screw.
!Compare the recommended tire inflation
pressure for your vehicle with the tire inflation
pressure on the yellow label located on the spare
wheel rim.
If the tire inflation pressure on the yellow label
on the spare wheel rim differs from the values
given in this Operator’s Manual, inflate the tire to
the recommended tire inflation pressure given
on the yellow label on the spare wheel rim.
!Do not operate the electric air pump longer
than 8 minutes without interruption. Otherwise it
may overheat.
You may operate the air pump again after it has
cooled off.