2008 MERCEDES-BENZ C300 light

276 Controls in detail
Panorama roof with power tilt/sliding panel*
Roller sunblinds
The roller sunblinds are designed to pro-
tect you from excessive sunlight streaming
in through the panorama roof with power
tilt/sliding panel.
The front roller sunblind only operates with
the tilt/sliding panel closed. The front and
rear roller sunblind cannot be operated in-
dividually.
Switch on the ignition.Operating roller sunblinds
Roof panel switch
1Extend front roller sunblinds
2Extend front roller sunblinds
3Retract front roller sunblinds
Extending or retracting: Move the
roof panel switch to the resistance
point in the required direction of
arrow1, 2 or3 until the roller sun-
blinds have reached their desired posi-
tion.
Express-extending: Move the roof
panel switch past the resistance point
in direction of arrow1 or 2 and re-
lease.
The roller sunblinds extends
completely.
Stopping during Express-extending:
Move the roof panel switch in any di-
rection.
Warning!G
When extending/retracting the roller sun-
blinds, make sure no one is in danger of be-
ing injured by the closing procedure. The
extending/retracting of the roller sunblinds
can be immediately halted by releasing the
switch or, if the switch was pressed past the
resistance point and released, by pressing
the switch in any direction.

277 Controls in detail
Panorama roof with power tilt/sliding panel*
Opening and closing panorama roof
with power tilt/sliding panel
The tilt/sliding panel only operates with
the roller sunblinds extended.
Warning!G
When opening or closing the tilt/sliding pan-
el, make sure there is no danger of anyone
being harmed by the opening or closing pro-
cedure.
The opening procedure of the tilt/sliding
panel can be immediately halted by releas-
ing the switch or, if the switch was moved
past the resistance point and released, by
moving the switch in any direction.
The closing procedure of the tilt/sliding
panel can be immediately halted by releas-
ing the switch.
The panorama roof with power tilt/sliding
panel is made out of glass. In the event of an
accident, the glass may shatter. This may re-
sult in an opening in the roof.
In a vehicle rollover, occupants not wearing
their seat belts or not wearing them properly
may be thrown out of the opening.
Such an opening also presents a potential
for injury for occupants wearing their seat
belts properly as entire body parts or por-
tions of them may protrude from the pas-
senger compartment.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children
unattended in the vehicle, or with access to
an unlocked vehicle. A child’s unsupervised
access to a vehicle could result in an acci-
dent and/or serious personal injury.
!To avoid damaging the seals, do not trans-
port any objects with sharp edges which can
stick out of the tilt/sliding panel.
Do not open the tilt/sliding panel if there is snow
or ice on the roof, as this could result in malfunc-
tions.
!Please keep in mind that weather conditions
can sometimes change rapidly. Make sure to
close the tilt/sliding panel when leaving the ve-
hicle. If water enters the vehicle interior, vehicle
electronics could be damaged which is not cov-
ered by the Mercedes-Benz Limited Warranty.
iWhen the panorama roof with power
tilt/sliding panel is open, resonance noises may
result in addition to the usual wind noises. They
are caused by minimal pressure changes in the
passenger compartment. To reduce or eliminate
these noises, change the position of the panora-
ma roof with power tilt/sliding panel or open a
side window slightly.
iYou can also open or close the tilt/sliding
panel using the SmartKey, see “Summer open-
ing feature” (
page 123) and “Convenience
closing feature” (
page 124).


285 Controls in detail
Loading and storing
Opening small and large storage
compartment: Press button1 or2
the armrests opens automatically to
the left and right side.
Closing small or large storage com-
partment: Swing the left or right arm-
rest backward until it engage.Parcel net in front passenger footwellA small convenience parcel net is located
in the front passenger footwell. It is for
small and light items, such as road maps,
mail, etc.
iThere is a small and a large storage compart-
ment located underneath the left armrest. The
small storage compartment can be removed for
the purpose of emptying.
Warning!G
The parcel net is intended for storing
light-weight items only.
Heavy objects, objects with sharp edges or
fragile objects may not be transported in the
parcel net. In an accident, during hard brak-
ing, or sudden maneuvers, they could be in-
jury to vehicle occupants.
The parcel net cannot protect transported
goods in the event of an accident.

286 Controls in detail
Loading and storing
Storage compartments in rear passen-
ger compartment
Armrest with integrated storage
compartment
1Release catch
Opening: Pull down the armrest.
Pull release catch 1 and swing the
cover upward in direction of arrow.Storage pockets
Storage pockets 1 are located on the
back of the front seats.
!Before storing the armrest in the backrest,
close the storage compartment cover.
!Do not sit on or lean your body weight
against the armrest when it is folded down, as
you could otherwise damage it.
Warning!G
The storage pocket is intended for storing
light-weight items only.
Heavy objects, objects with sharp edges or
fragile objects may not be transported in the
storage pocket. In an accident, during hard
braking, or sudden maneuvers, they could
be thrown around inside the vehicle and
cause injury to vehicle occupants.
The storage pocket cannot protect trans-
ported goods in the event of an accident.

288 Controls in detail
Loading and storing
Closing: Open the armrest storage
compartment.
Swing cup holder2 backward until it
engaged.
Trunk
Retaining hooks
Two hooks are located on the upper edge
of the trunk and can be used to attach car-
go items such as bags.
Use the hooks to secure light weight items
only. The maximum permissible weight per
hook is 9 lb (4 kg).Parcel net in trunk
There is a parcel net on the left trunk side
walls to secure loads.
The parcel net is intended for storing
light-weight items only. The parcel net can-
not protect transported goods in the event
of an accident.
!Do not use the retaining hooks to tie down
cargo.

292 Controls in detail
Useful features
Rear seat ashtray
1Ashtray insert
2Cover
3Button
Opening: Pull at top of cover2.
Removing ashtray insert: Push
button3 to disengage ashtray
insert1 and remove it.
Reinstalling ashtray insert: Push the
ashtray insert1 down into the retain-
er until it engages.
Push at top of cover2 to close
ashtray.
Cigarette lighter
Switch on the ignition.1Cover
2Cigarette lighter
Press cover plate1 forward until it en-
gaged.
Push in cigarette lighter2.
The cigarette lighter will pop out
automatically when hot.
Warning!G
Never touch the heating element or sides of
the cigarette lighter; they are extremely hot.
Hold the knob only.
Make sure any children traveling with you do
not injure themselves or start a fire with the
hot cigarette lighter.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
(Canada only) from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle.
A child’s unsupervised access to a vehicle
could result in an accident and/or serious
personal injury.

293 Controls in detail
Useful features
Tap the front of the cover plate1.
The cover will retract and the ashtray
will close.Power outlet in the glove box
1Power outlet
Switch on the ignition.
Open the glove box (page 284).
Flip cover from power outlet1 to the
right and insert electrical plug (ciga-
rette lighter type).Power outlet in the rear passenger
compartment
1Power outlet
2Cover
Switch on the ignition.
Pull at top of cover2.
Flip cover from power outlet1 to the
left and insert electrical plug (cigarette
lighter type).
!The lighter socket can accommodate 12V
DC electrical accessories (up to a maximum of
85 W) designed for use with the standard “ciga-
rette lighter” plug type. Keep in mind, however,
that connecting accessories to the lighter socket
(for example extensive connecting and discon-
necting, or using plugs that do not fit properly)
can damage the lighter socket. With the socket
damaged, the lighter may no longer be able to be
placed in the heating (pushed-in) position, or the
lighter may pop out too early with the lighter not
hot enough.
To help avoid damaging the cigarette lighter
socket, we recommend connecting 12V DC elec-
trical accessories designed for use with the stan-
dard “cigarette lighter” plug type to the 12V
power outlet (
page 293) in your vehicle when-
ever possible.
iThe power outlet1 can be used to
accommodate electrical consumers (e.g. air
pump, auxiliary lamps) up to a maximum
of 180 W.
iThe power outlet1 can be used to
accommodate electrical consumers (e.g. air
pump, auxiliary lamps) up to a maximum
of 180 W.

304 Controls in detail
Useful features
Programming integrated remote con-
trol
Step 1:
Switch on the ignition (page 82).
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1 be-
gins to flash after approximately
20 seconds (do not hold the button for longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:
Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.Indicator lamp1 will flash, first slowly
and then rapidly.
Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health.
All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and possible death.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.