2008 MERCEDES-BENZ C-Class ESP

95 Telephone
COMAND phone book
Entering data into a field
Select all the characters one after the
other in the predictive speller 3.
i The predictive speller provides the charac-
ters corresponding to the selected data field.
To switch predictive speller to up-
per or lower case characters: Select
( or &.
To switch predictive speller charac-
ter set: Select #.
Every time this is selected it switches
the character set.
To change the predictive speller lan-
guage: Select !.
Rotate ymz or slide qmr until the re-
quired language is highlighted and
press n.
To move the cursor in the data field:
Select Y or Z.
Deleting an entry
To delete an individual character:
Select õ and briefly press n.
or
Press the î button next to the
COMAND controller.The character to the left of the cursor is
deleted.
To delete an entire entry: Select
õ and press and hold n until the
entire entry has been deleted.
or
Press and hold î until the entire en-
try has been deleted.
Cancelling an entry
Select A.
If one of the data fields contains data,
you will be prompted to confirm wheth-
er you wish to save the entry.
Select “Yes” or “No”.
The entry will be saved or discarded
on the basis of the selection.
Saving entry
Select B
A corresponding message is displayed.The deletion rules vary according to the en-
try selected:

Phone book entry selected:
The entry is deleted in the COMAND
phone book and the address book if the
address book entry only contains
phone numbers.

Entire address book entry selected:
The entry is deleted in the COMAND
phone book and additionally also in the
address book if the address book entry
only contains phone numbers.

Subentry of an address book entry se-
lected:
The subentry is deleted in the
COMAND phone book and in the ad-
dress book.
To delete: Select entry (page 104).
Select “Options” K “Delete”.
You will be prompted to confirm that
you really want to delete the entry.
Select “Yes” or “No”.
“Yes” option: The entry is deleted ac-
cording to the above rules.
Deleting entry

99 Telephone
Call lists
i The speller provides the characters corre-
sponding to the selected data field.
To switch predictive speller to up-
per or lower case characters: Select
( or &.
To switch predictive speller charac-
ter set: Select #.
Every time this is selected it switches
the character set (digits, lower case let-
ters).
To change the predictive speller lan-
guage: Select !.
Rotate ymz or slide qmr until the re-
quired language is highlighted and
press n.
To move the cursor in the data field:
Select Y or Z.
To delete an individual character:
Select õ and briefly press n.
or
Press the î button next to the
COMAND controller.
The character to the left of the cursor is
deleted.
To delete an entire entry: Select
õ and press and hold n until the
entire entry has been deleted.
or
Press and hold î next to the
COMAND controller until the entry has
been deleted.
To save entry: Select B
A corresponding message is displayed.
To cancel entry: Select “Back”.
If one of the data fields contains data,
you will be prompted to confirm wheth-
er you wish to save the entry.
Select “Yes” or “No”.
The entry will be saved or discarded
on the basis of the selection.Adding a phone number from the call list
to an existing address book entry
Select the list entry (page 97).
Select “Options” K “Save”K“Add
Phone No.”.
i “Save” has no function if the selected list
entry is already saved in the address book.
Select a number category, e. g.
“Home”.
Select a phone category, e. g.
“Mobile Phone”.
Select “Save”.
The search menu for address book en-
tries appears.
Search for the required entry.
i Please see the “Searching for an address
book entry” section (
page 106) for a detailed
description on searching for an address book en-
try.
Press n after completing the search.
If there are fewer than five numbers
saved for the required entry in the se-
lected number category, COMAND
saves the data.
A corresponding message is displayed.

102 Telephone
Making calls
To select call: Rotate ymz or slide
qmr.
To initiate call: Press n.
Initiating a call to a call list entry or
COMAND phone book entry
Open the call list and select an entry
(
page 97).
or
Open the COMAND phone book and
select an entry (
page 104).
To initiate call: Press n.Phone mode with a single call
1Other party
2Symbol for active phone connection
3Switches the hands-free microphone
off or on
4Sends DTMF tones (not possible with
all mobile phones)
5Device name of the connected mobile
phone
6Terminates callSwitching hands-free microphone on or
off
Open the phone main menu
(
page 92).
To switch off: Select “Mic Off”.
When the microphone is switched off
the symbol > appears in the main ar-
ea.
To switch on: Select “Mic On”.
The symbol > disappears
Sending DTMF tones
i This function is not possible with all mobile
phones.
Answering machines or other devices can
be controlled via DTMF tones, e. g. for re-
mote query functions.
To transmit individual characters:
During a call select the required char-
acters using the COMAND controller.
or
Press the corresponding button on the
COMAND control unit keypad.
Every selected character is transmitted
immediately.
Functions during a single call

105 Telephone
Address book
i You can create address data directly in the
address book. If you save phone numbers in the
COMAND phone book, these are saved in the ad-
dress book. When you save a navigation destina-
tion, COMAND creates an address book entry
containing the complete address data that sup-
port navigation.
Open the address book (page 104)
and select “New”.
The input menu with the data fields and
the speller appears.
Input menu with data fields
1Selected data field with cursor
2Speller
Switching data field
Slide qm repeatedly until the predic-
tive speller is hidden.
Then slideqmr and press n to select
a data field.
or
Select [ or ] in the speller.
The input menu indicates the selected
data field.
Entering data into a field
Select all the characters one after the
other in the predictive speller 2.
i The predictive speller provides the charac-
ters corresponding to the selected data field.
To switch predictive speller to up-
per or lower case characters: Select
( or &.
To switch predictive speller charac-
ter set: Select #.
Every time this is selected it switches
the character set.
To change the predictive speller lan-
guage: Select !.
Rotate ymz or slide qmr until the re-
quired language is highlighted and
press n.
To move the cursor in the data field:
Select Y or Z.
Deleting
To delete an individual character:
Select õ and briefly press n.
or
Press î button next to the
COMAND controller.
The character to the left of the cursor is
deleted.
To delete an entire entry: Select
õ and press and hold n until the
entire entry has been deleted.
or
Press and hold î until the entire en-
try has been deleted.
Creating a new address book entry

112 Navigation
Introduction
The digital data for the map software will
become obsolete, just like conventional
road maps. Optimum route guidance by
the navigation system is only achieved
with up-to-date map software. Information
on new map software versions is available
from an authorized Mercedes-Benz Center.
You can have the map software updated
there by means of a DVD or perform the
update process yourself.
Notes on DVD discs

Only touch the discs at the edges.

Handle the discs with care in order to
prevent reading errors.

Avoid scratching, leaving fingerprints
and dust on the discs.

Use a commercially available cleaning
cloth to clean discs. Always wipe in a
straight line from the inside outwards,
never in a circular motion.

After use, put the discs back into the
box.

Protect the discs from heat and direct
sunlight.
Introduction
Safety instructions
G Warning
For safety reasons, only enter a destination
when the vehicle is stationary. When the ve-
hicle is in motion, a passenger should enter
the destination. Study manual and select
route before driving.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
COMAND calculates the route to the desti-
nation without taking account of the follow-
ing:

Traffic lights

Stop and right-of-way signs

Lane merging

Parking or stopping prohibited areas

Other road and traffic rules and regula-
tions

Narrow bridges
G Warning
COMAND may give incorrect navigation
commands if the data in the digital map
does not correspond with the actual road/
traffic situation. Digital maps do not cover
all areas nor all routes within an area. For ex-
ample, if the traffic routing has been
changed or the direction of a one-way road
has been reversed.
For this reason, you must always observe
applicable road and traffic rules and regula-
tions during your journey. Road and traffic
rules and regulations always have priority
over the navigation commands generated by
the system.
G Warning
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.
Updating the map software

114 Navigation
Introduction
Update process
The update process starts once the DVD
has been loaded.
COMAND checks whether the map soft-
ware on the DVD matches the vehicle’s
navigation system and system software.
Map software is not suitable for the
navigation system or the system soft-
ware
A message is displayed stating that the
navigation update DVD with the new map
data is not suitable for the system or the
system software.
COMAND ejects the DVD.
Remove the DVD from the slot 1.
Have the system software updated by
an authorized Mercedes-Benz Center.
i It will only be possible to update the map
software once the system software has been up-
dated.
Map software matches the navigation
system and the current system software
COMAND checks whether the DVD’s map
data has already been installed.Map data is already installed
The version release and a corresponding
message will be given on the display.
To confirm message: Press n.
COMAND ejects the DVD.
Map data is not yet installed
The version release and a query as to
whether the update should be carried out
will be given on the display.
Select “Yes” or “No”.
If “No” is selected, COMAND ejects the
DVD automatically and the map data is
not updated.
Remove the DVD from the slot 1.
If “Yes” is selected, the map data is up-
dated.
Updating the map data
While the update is in progress, a corre-
sponding message and a progress bar are
displayed. The progress bar fills from left
to right over the course of the update. The
navigation system is not functional until
the update is complete.You cannot eject the DVD during the up-
date. If you switch COMAND off during the
update, this will interrupt the update and
the update will resume at the point of inter-
ruption when the system is restarted.
While updating, COMAND may prompt you
to change the DVD. A corresponding mes-
sage is then displayed.
Press the Eject button u.
COMAND ejects the DVD.
Remove the DVD from the slot 1.
Insert the DVD requested by COMAND.
If the update has been completed suc-
cessfully, a corresponding message is
displayed.
To confirm message: Press n.
COMAND ejects the DVD.
Remove the DVD from the slot 1.
The update is complete.
If the update has not been completed suc-
cessfully, a message is displayed indicat-
ing that the map update is not possible.
To confirm message: Press n.
COMAND ejects the DVD.
Remove the DVD from the slot 1.

119 Navigation
Introduction
Displaying/hiding menu system
To hide: Slide qm and when the menu
item “Full Screen” is displayed press
n.
The menu system is hidden. This dis-
plays the map in full screen mode.
To display: In full-screen map mode
press n.
or
Press the function button z.
Setting the map scale
i You can only set the map scale when the
menu system is hidden (map in full-screen
mode).
Rotate ymz until the required map
scale is set.
The map scale 3 is displayed as soon
as you start rotating ymz. Rotating
clockwise makes the map smaller, ro-
tating anticlockwise enlarges it.1Currently set map scale as number,
here 1 mi (1 inch on the map corre-
sponds to 1 mi)
2Indicator on the map scale pointing to
the currently selected map scale
3Map scale
Saving current vehicle location as des-
tination in the last destinations
To display menu system if applica-
ble: Press n.
To save: Select “Position” K “Save Ve-
hicle Position”.
COMAND saves the current vehicle lo-
cation as a destination in the last desti-
nations memory (
page 162). A
window appears containing a corre-
sponding message.
To exit menu: Slide omp or press the
í button.
Scrolling the map
i You can only scroll the map when the menu
system is hidden.
Hide menu system if applicable
(
page 119).
Slide qmr, omp or wmx.
Crosshairs will appear on the map.
1Current vehicle location
2Crosshairs
3Information on crosshairs position
4Set map scale
i The display 3 may for example be a road if
corresponding data is available in the digital map
and “Current Street” is activated. Or it displays
the geo-coordinate position of the crosshairs if
“Geo-coordinates” display is activated.
(
page 124).

120 Navigation
Introduction
Saving crosshairs position as destina-
tion in the last destinations
To display menu system if applica-
ble: Press n.
To save: Select “Position” K “Save
Crosshair Position”.
COMAND saves the crosshairs position
as a destination in the last destinations
memory (
page 162). A window ap-
pears containing a corresponding mes-
sage.
Hiding crosshairs
Press the í button.
The crosshairs disappear and the map
is set to the vehicle location.
or
Set the map to the vehicle location, see
description below.Setting map to vehicle or destination
location
i If you have moved the map, you can quickly
move the map to the vehicle or destination loca-
tion using this function. It is only possible to set
it to the destination location when route guid-
ance is active.
To display menu system if applica-
ble: Press n.
To set map to vehicle location:
Select “Position”
K “Vehicle Position
Map”.
or
Press the í button if the crosshairs
are displayed.
i This hides the crosshairs.
To set to destination location: Select
“Position”
K “Destination Position
Map”.
The crosshairs position is then set to
the destination.
i You can perform the settings listed below
with route guidance inactive or active.
Map display
Map orientation
1Currently set map orientation
The following displays are possible:

9 = orientation to north (the map dis-
play is oriented to the north, north is al-
ways at the top)

8 = Driving direction (the map display
is oriented in the direction of travel, the
direction of travel is always at the top,
the orange tip of the symbol points
northwards)
Basic settings