2008 MERCEDES-BENZ C-Class Page 35

153 Navigation
Route guidance
Route guidance from an off-road posi-
tion to a destination
If the vehicle location is within the area
covered by the digital map, but the map it-
self does not contain any information on
the location, the vehicle is in an off-road
position. COMAND can guide you from
such a position to a destination.
At the start of route guidance you will see
the message “Off Mapped Road”, an arrow
and the distance to the destination. The ar-
row indicates the direction of the actual
destination.
The blue marking for the route on the map
starts from the nearest road known to the
system.
As soon as the vehicle is travelling again on
a road known to the system, route guid-
ance continues in the usual manner.
Route guidance from an off-map posi-
tion to a destination
If the vehicle location is outside the area
covered by the digital map, then the vehi-
cle is in an off-map position.
COMAND can guide you from such a posi-
tion to a destination.At the start of route guidance you will see
the message “Off Map”, an arrow and the
distance to the destination. The arrow indi-
cates the direction of the actual destina-
tion.
The blue marking for the route on the map
starts from the nearest road known to the
system.
As soon as the vehicle is travelling again on
a road known to the system, route guid-
ance continues in the usual manner.
Off-road during route guidance
The actual path of the road may deviate
from the data in the digital map due to road
works.
In cases like this, the system is temporarily
not able to locate the vehicle location on
the digital map; the vehicle is thus in an off-
road position.
The display then shows the message “Off
Mapped Road”, an arrow and the distance
to the destination. The arrow indicates the
direction of the actual destination.
As soon as the vehicle location is found
again, route guidance continues in the usu-
al manner.
i During an active telephone call, the naviga-
tion announcements are suppressed.
If you missed an announcement, you can
request a current announcement at any
time.
To request current announcement:
Select “Navi”
K 6.
or
In the map display with the menu sys-
tem displayed (
page 119) select
6.
To switch off navigation announce-
ments: Press
V during the announce-
ment.
Navigation announcements
G Warning
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.


154 Navigation
Route guidance
The message “The driving instructions
have been muted” appears briefly.
To switch navigation announce-
ments back on again manually: Se-
lect “Navi”
K 6.
or
In the map display with the menu sys-
tem displayed (
page 119) select
6.
or
Start new route calculation
(
page 135).
or
If you switch COMAND on again or
start the engine.
To set the volume of the announce-
ments: Set the volume during an auto-
matic announcement Setting the
volume (
page 35).
or
Call up an announcement manually us-
ing “Navi”
K 6 and set the volume
(
page 35).
In the map display with the menu sys-
tem displayed (
page 119) select
“Destination”
K “Cancel Route
Guidance”.
In the map display with the menu sys-
tem displayed (
page 119) select
“Destination”
K “Continue Route
Guidance”.
COMAND calculates the route.
i The Detour function blocks a route segment
ahead. You can set the length of the block.
COMAND calculates a detour route if possible.
In the map display with the menu sys-
tem displayed (
page 119) select
“Route”
K “Detour”.
To set length of block: Select
“Longer” or “Shorter” repeatedly until
the required length is set.The blocked segment is highlighted in
red/white on the map. Shown at the
top of the display is the length of the
blocked segment and the route seg-
ment to which the block goes.
To cancel the function: Select “Back”.
To start route calculation: Select
“Start”, see also (
page 135).
To change a block: Select “Navi” K
“Route”
K “Detour” K “Change”.
i If a block already exists, the message “De-
tour Already Set” is displayed. You can then
change or delete this.
Then set length of block.
To delete block: Select “Navi” K
“Route”
K “Detour” K “Delete”.
i If a block already exists, the message “De-
tour Already Set” is displayed. You can then
change or delete this.
Cancelling route guidance
Resuming route guidance after
cancelling
Detour function

155 Navigation
Route guidance
i You can have other routes calculated for the
original route guidance using the “Alternative
Route” function.
In the map display with the menu sys-
tem displayed (
page 119) select
“Route”
K “Alternative Route”.
The display is split into two halves. On
the left is the map, which displays one
or more alternative routes between the
start and the destination. The current
route is highlighted in dark blue, other
alternative routes are light blue.
The right side of the display shows in-
formation on the active alternative
route, e.g. length of the segment and
the estimated time of arrival.
To select next or previous alterna-
tive route: Select “Next” or “Previous”.
The selected route is now highlighted
in dark blue.
To return to the original route guid-
ance: Select “Back”.
To start route guidance with the se-
lected alternative route guidance:
Select “Start”.
i The route browser provides an overview of
the route. You can move along the route seg-
ment by segment using the route browser and
view information and details about the route seg-
ments.
In the map display with the menu sys-
tem displayed (
page 119) select
“Route”
K “Route Browser”.
The route browser is in the display.
The top of the display shows informa-
tion on the highlighted route segment,
e. g. the road and the segment of the
road to be driven.
The highlighted route segment is iden-
tified on the map by its white color and
red edge.
To display next or previous route
segment: Select “Next” or “Previous”.
To enlarge or reduce the map
display: Select ; or :.
To close route browser: Select
“Back”.
In the map display with the menu sys-
tem displayed (
page 119) select
“Route”
K “Destination Information”.
The destination information is given in
the display.
Example display with main destination and
stopover destination
1Distance/estimated time of arrival/es-
timated journey time to the stopover
destination
2Stopover destination=
3State and City
4Main destination <
5Distance/estimated time of arrival/es-
timated journey time to the main desti-
nation
Alternative routeRoute browserDisplaying destination information

156 Navigation
Route guidance
i When calculating the estimated time of ar-
rival, COMAND uses the time set on the CO-
MAND as its basis. For this reason, the time on
COMAND must be set correctly (
page 165).
The calculation of the estimated time of arrival
does not specifically take into consideration
whether it is summer time or standard time at
the destination. It is not taken into consideration
whether or not the destination is in a different
time zone.
The distance to the destination, the estimated
time of arrival and the estimated remaining jour-
ney time 1, 5 are not displayed until the route
calculation is complete.
To close destination information:
Slide omp.
or
Press the í button.

157 Navigation
Destination memory
i There is always an entry in the destination
memory with the name “My Address” at the top
of the list. You can assign your home address, for
example, to this entry. If the “My Address” entry
already contains data that support navigation
(Q symbol), you can select this for route guid-
ance.
Assigning home address for first time
or changing
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Memo-
ry”.
If there are more than 8 entries in the
destination memory, the destination
memory list with predictive speller is
displayed, otherwise the destination
memory list is displayed without
predictive speller (
page 137).
If the list without predictive speller is
displayed, the entry “My Address” is
highlighted automatically.1Entry already contains data that sup-
port navigation Q
2Calls up options
Switching to the destination memory list
without predictive speller
Slide qm repeatedly until the predic-
tive speller disappears.
The entry “My Address” is highlighted
automatically in the list provided you
have not entered any characters in the
predictive speller.
If you have previously entered charac-
ters in the predictive speller:
Rotate ymz or slide qm in the list
until the entry “My Address” is high-
lighted.
or
To assign address for first time:
Press and hold n until the predictive
speller disappears.
The entry “My Address” is highlighted
automatically in the list.
To exit menu: Select “Back”.
How you proceed from here depends
on whether you wish to enter the ad-
dress manually or use an address book
entry that supports navigation as your
home address.
Entering address manually
Switch to the destination memory list
without predictive speller if necessary.
To assign address for first time:
Press n and select “New Entry”.
To change home address: Select
“Options”
K “New Entry”.
In both cases, the Enter Destination
menu appears.
Enter the address. Proceed as de-
scribed for entering a destination in the
“Entering a destination via the ad-
dress” section (
page 126).
Destination memory
Home address


158 Navigation
Destination memory
After entering the address, select
“Save”.
COMAND then saves the entry. A mes-
sage is displayed and then the Enter
Destination menu with the selected ad-
dress. “Start” is highlighted automati-
cally.
Using address book entry as home ad-
dress
Switch to the destination memory list
without predictive speller if necessary
(
page 157).
To assign address for first time:
Press n and select “Assign to Address
Book Entry”.
or
To change home address: Select
“Options”
K “Assign to Address Book
Entry”.
In both cases you will see either the list
or, if there are more than 8 address
book entries, the search menu with
search speller.
Select the desired address book entry.
Proceed as described in the “Searching
for an address book entry” section
(
page 106).
i Under “Assigning a destination to an ad-
dress book entry” on (
page 160) you will find
out how to link address book entries to data that
support navigation.
To confirm selection: Press n.
Address assigned for first time:
COMAND saves the entry. A message is
displayed and then the Enter Destination
menu with the selected address. “Start” is
highlighted automatically.
To change address:
You will be prompted to confirm that you
wish to overwrite the “My Address”.
Select “Yes” or “No”.
If you select “Yes” COMAND overwrites
the destination. A message is displayed
and then the Enter Destination menu
with the selected address. “Start” is
highlighted automatically.
If you select “No” the list reappears.Selecting home address for route guid-
ance
i If the “My Address” entry already contains
data that support navigation (Q symbol), you
can select this for route guidance.
If the symbol is missing, then first assign a desti-
nation to this entry (
page 157).
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Memo-
ry”.
If there are more than 8 entries in the
destination memory, the destination
memory list with predictive speller is
displayed, otherwise the destination
memory list is displayed without
predictive speller (
page 137).
Destination memory list with
predictive speller: Slide qm repeat-
edly until the list appears without the
speller.
or
Select B
Press n.
Destination memory list without
predictive speller: Press n.

159 Navigation
Destination memory
The Enter Destination menu is dis-
played with the address data for the
home address. “Start” is highlighted
automatically.
Starting route calculation
Press n.
Route guidance begins after the route
has been calculated (
page 148).
i This function also saves the destination to
the address book. COMAND creates an address
book entry there, which contains the complete
address data that support navigation. You can
then select this entry in the address book and
from there start navigation to the address.
After entering the address
After entering the address
(
page 126), select “Save”.
Now you can select memory options.
During route guidance
Display menu system if applicable
(
page 118).
Select “Destination” K “Save Destina-
tion”.
Now you can select memory options.
Accepting from the last destinations
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Last
Destinations”.
The list of last destinations appears.
To select a destination: Rotate ymz
or slide qmr.
To confirm destination: Press n.
The address of the destination is dis-
played.
Select “Save”.
or
Select destination and then “Options”
K “Save”.
In both cases, you can then select
memory options.
Saving a destination in the destina-
tion memory

160 Navigation
Destination memory
Selecting memory options
Saving destination without name
Select “Save Without Name”.
COMAND saves the destination in the
destination memory and uses the ad-
dress as the destination name.
or
Select “Save as My Address”.
COMAND saves the destination under
the “My Address” entry in the destina-
tion memory.
If the entry already contains data that
support navigation, you will be prompt-
ed to confirm that you wish to over-
write the previous destination address.
Select “Yes” or “No”.
If you select “Yes” the message “Saving
Procedure Successful” appears, select-
ing “No” cancels the operation.
Saving destination with name
Select “Save With Name”.
Select desired category, e. g. “Home”.
The input menu is displayed with the
data fields and the predictive speller.1Selected data field with cursor
2Predictive speller
To enter data: Continue with the step
“Switching data field” (
page 105) in
the “Creating a new address book en-
try” section.
COMAND saves the destination under
the name entered.
Assigning destination to an address
book entry
i This function assigns the complete address
data that support navigation to an existing ad-
dress book entry. You can then select this entry
in the address book and from there start naviga-
tion to the address.
Select “Assign to Address Book Entry”.
Select the desired category, e. g.
“Home”.
You will see either the list or, if there
are more than 8 address book entries,
the search menu with search speller.
Select the desired address book entry.
Proceed as described in the “Searching
for an address book entry” section
(
page 106).
If the selected address book entry does
not yet contain any address data that
support navigation, COMAND saves
the data.
If the selected address book entry al-
ready contains address data that sup-
port navigation, you will be prompted
to confirm that you wish to overwrite
the existing data.
Select “Yes” or “No”.
If you select “Yes” COMAND saves the
data.