119 Navigation
Introduction
Displaying/hiding menu system
To hide: Slide qm and when the menu
item “Full Screen” is displayed press
n.
The menu system is hidden. This dis-
plays the map in full screen mode.
To display: In full-screen map mode
press n.
or
Press the function button z.
Setting the map scale
i You can only set the map scale when the
menu system is hidden (map in full-screen
mode).
Rotate ymz until the required map
scale is set.
The map scale 3 is displayed as soon
as you start rotating ymz. Rotating
clockwise makes the map smaller, ro-
tating anticlockwise enlarges it.1Currently set map scale as number,
here 1 mi (1 inch on the map corre-
sponds to 1 mi)
2Indicator on the map scale pointing to
the currently selected map scale
3Map scale
Saving current vehicle location as des-
tination in the last destinations
To display menu system if applica-
ble: Press n.
To save: Select “Position” K “Save Ve-
hicle Position”.
COMAND saves the current vehicle lo-
cation as a destination in the last desti-
nations memory (
page 162). A
window appears containing a corre-
sponding message.
To exit menu: Slide omp or press the
í button.
Scrolling the map
i You can only scroll the map when the menu
system is hidden.
Hide menu system if applicable
(
page 119).
Slide qmr, omp or wmx.
Crosshairs will appear on the map.
1Current vehicle location
2Crosshairs
3Information on crosshairs position
4Set map scale
i The display 3 may for example be a road if
corresponding data is available in the digital map
and “Current Street” is activated. Or it displays
the geo-coordinate position of the crosshairs if
“Geo-coordinates” display is activated.
(
page 124).
138 Navigation
Destination input
1Current vehicle location (displayed if
the vehicle location is close to the
crosshairs position)
2Crosshairs
3Information on crosshairs position
4Set map scale
i The display 3 depends on the setting se-
lected in “Information On Map” (
page 123). It
may display the current road if corresponding
data is available in the digital map. Or it displays
the geo-coordinate position of the crosshairs if
“Geo-coordinates display” is activated
(
page 124) and if there is adequate GPS re-
ception.
Moving the map and selecting a desti-
nation
To move the map: Slide qmr, omp or
wmx.
To set the map scale: Rotate ymz.
Rotating clockwise makes the map
smaller, rotating counterclockwise en-
larges it.
To select a destination: Press n.
If the crosshairs are outside the digital
map, a route to this destination cannot
be calculated and the message “The
crosshair is off the map” is displayed.
Select “OK”.
If the destination is within the digital
map, COMAND tries to find the desti-
nation on the map.
If the destination can be found, the En-
ter Destination menu is displayed with
the address of the destination. Other-
wise you will see the entry “Destination
From Map”.
To start route calculation: Select
“Start”, see also (
page 135).
i If route guidance is active, you can enter a
stopover destination. Stopover destinations may
be predefined destinations in the following cate-
gories suggested by COMAND for you to select:
“Mercedes-Benz Service”
“Hospital”
“Gas Station”
“Parking Lot”
“Restaurant”
However, you can also enter destinations other
than those that have been predefined. Select the
menu item “OTHER” for this purpose.
You can influence the route guidance to the main
destination in a specific way using the stopover
function. Once the stopover destination has
been reached, COMAND automatically recalcu-
lates the route to the main destination.
Entering predefined destinations
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “Stopover”.
Entering stopover destination
