2008 INFINITI FX35 mount

HOODBL-13
< SERVICE INFORMATION >
C
DE
F
G H
J
K L
M A
B
BL
N
O P
HOOD
Fitting AdjustmentINFOID:0000000001327783
LONGITUDINAL AND LATERAL CLEARANCE ADJUSTMENT
1. Remove hood lock assembly, loosen the hood hinge nuts and close the hood.
2. Adjust the lateral and longitudinal clearance, and open the hood to tighten the hood hinge mounting bolts
to the specified torque.
3. Install the hood lock temporarily, and align the hood stri ker and lock so that the centers of striker and lock
become vertical viewed from the front , by moving the hood lock laterally.
4. Tighten hood lock mounting bolts to the specified torque.
CAUTION:
Adjust right/left clearance between hood an d headlamp to the following specification.
FRONT END HEIGHT ADJUSTMENT
1. Remove the hood lock and adjust the height by rota ting the bumper rubber until the hood becomes 1 to1.5
mm (0.04 to 0.059 in) lower than the fender.
2. Temporarily tighten the hood lock, and position it by engaging it with the hood striker. Check the lock and
striker for looseness, and tighten the hood lock mounting bolts to the specified torque.
SURFACE HEIGHT ADJUSTMENT
1. Remove hood lock, and adjust the surface height difference of hood, fender and headlamp according to
the fitting standard dimension, by rotating RH and LH bumper rubbers.
2. Install hood lock temporarily, and move hood lock laterally until the centers of striker and lock become ver- tical when viewed from the front.
1. Hood hinge 2. Nut 3. Hood stay
4. Hood lock 5. Bolt 6. Bumper rubber
PIIB1212E
Hood and headlamp (C–C) : Less than 2.0 mm (0.08 in)
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

HOODBL-15
< SERVICE INFORMATION >
C
DE
F
G H
J
K L
M A
B
BL
N
O P
1. Support the hood striker with a proper material to prevent it from falling.
WARNING:
Body injury may occur if no supporting rod is holding the
hood open when removi ng the hood stay.
2. Remove the hood stays from the stud balls on the body side.
3. Remove the hinge mounting nuts on the hood to remove the hood assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Hood Lock ControlINFOID:0000000001327785
REMOVAL
1. Remove the front grill. Refer to EI-22, "Component Parts Location".
2. Remove the front fender protector (LH). Refer to EI-24, "
Component Parts Location".
3. Disconnect the hood lock cable from the hood lock, and c lip it from the radiator core support upper and
hood ledge.
4. Remove instrument driver lower panel. Refer to IP-11, "
Removal and Installation".
5. After the bolt of the case with the air cleaner is disconnected, and it is moved, the cable is pulled.
PIIA6058E
1. Hood lock 2. Hood lock cable 3. Clip
4. Hood ledge upper front (LH) 5. Dash lower cross member reinforce (LH)
PIIA6017E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BL-18
< SERVICE INFORMATION >
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Removal and InstallationINFOID:0000000001327787
REMOVAL
1. Remove the front fender protector. Refer to EI-24, "Component Parts Location".
2. Remove the front bumper. Refer to EI-14, "
Component Parts Location".
3. Remove the ICC. Refer to ACS-65
.
4. Remove the headlamp. Refer to LT-30, "
Removal and Installation".
5. Remove the washer tank. Refer to WW-28, "
Removal and Installation of Washer Tank".
6. Remove the resonator. Refer to EM-17
or EM-173.
7. Remove the power steering oil cooler. Refer to PS-37
.
8. Remove the ambient sensor. Refer to ATC-99, "
Removal and Installation".
9. Remove the crash zone sensor. Refer to SRS-42, "
Removal and Installation".
10. Remove the horn connector, cooling fan connector and harness clip.
11. Remove the hood lock and disconnect hood lock control cable. Refer to BL-15, "
Removal and Installation
of Hood Lock Control".
12. Remove the reservoir tank. Refer to CO-40, "
Removal and Installation" or CO-13, "Removal and Installa-
tion".
13. Remove mounting blots and remove radiator core support. Remove mounting bolts with power tool.
14. After remove radiator core suppor t, remove the horn, cooling fan.
1. Radiator core support assembly 2. Bolt 3. Bolt
4. Horn (High) 5. Air guide (RH) 6. Cooling fan
7. Air guide (LH) 8. Horn (Low)
PIIA6018E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BL-20
< SERVICE INFORMATION >
FRONT FENDER
FRONT FENDER
Removal and InstallationINFOID:0000000001327788
REMOVAL
1. Remove the front bumper. Refer to EI-14, "Component Parts Location".
2. Remove the headlamp. Refer to LT-30, "
Removal and Installation".
3. Remove the front fender protector. Refer to EI-24, "
Component Parts Location".
4. Remove the mounting bolt and remove the front fender.
CAUTION:
While removing use a shop cloth to protect body from damaging.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 After installing, apply touch-up paint (the body color) onto the head of the front fender mounting
bolts.
 After installing, check front fender adjustment. Refer to BL-13, "
Fitting Adjustment" and BL-131, "Fit-
ting Adjustment".
1. Front fender 2. Bolt
PIIA6076E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

DOOR
BL-131
< SERVICE INFORMATION >
C
D E
F
G H
J
K L
M A
B
BL
N
O P
DOOR
Fitting AdjustmentINFOID:0000000001327873
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End.
Loosen the hinge mounting bolts. Raise the front door at rear end to adjust.
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End.
1. Remove the center pillar upper garnish and center pillar lower garnish. Refer to EI-38, "Component Parts
Location".
2. Accessing from inside the vehicle, loosen the mount ing nuts. Open the rear door, and raise the rear door
at rear end to adjust.
STRIKER ADJUSTMENT
1. Front fender 2. Front door outer 3. Rear door outer
4. Bolt 5. Nut
PIIA6059E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BL-132
< SERVICE INFORMATION >
DOOR
Adjust the striker so that it becomes parallel with the lock insertion
direction.
Removal and Installation of Front DoorINFOID:0000000001327874
CAUTION:
 When removing and installing the front door assembl y, support the door with a jack and cloth to pro-
tect the door and body.
 When removing and installing front door assembly, be sure to carry out the fitting adjustment Refer
to BL-131, "
Fitting Adjustment".
 Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
 After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
 Operate with two workers, because of its heavy weight.
 After installing, check operation.
REMOVAL
1. Pull the lever and remove the front door harness connector
while removing tabs of door harness connector.
2. Remove the mounting bolts of the check link on the vehicle.
3. Remove the door-side hinge mounting nuts, and remove the door assembly. : 16.7 N·m (1.7 kg-m, 12.4 ft-lb)
PIIB2804J
PIIA2514E
PIIA6020E
PIIA6021E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

DOOR
BL-133
< SERVICE INFORMATION >
C
D E
F
G H
J
K L
M A
B
BL
N
O P
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear DoorINFOID:0000000001327875
CAUTION:
 When removing and installing th e rear door assembly, support the do or with a jack and cloth to pro-
tect the door and body.
 When removing and instal ling rear door assembly, be sure to ca rry out the fitting adjustment Refer
to BL-131, "
Fitting Adjustment".
 After installing, apply touch-up paint (the body co lor) onto the head of the hinge mounting nuts.
 Operate with two workers, because of its heavy weight.
 Check the hinge rotating part for poor lu brication. If necessary, apply “body grease”.
 After installing, check operation.
REMOVAL
1. Grommet is pulled out, and the Rear door harness connector is detached.
2. Remove the mounting bolts of the check link on the vehicle.
3. Remove the door-side hinge mounting nuts, and remove the door assembly.
INSTALLATION
Install in the reverse order of removal.
PIIA2787E
PIIA6022E
PIIA6023E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

BL-134
< SERVICE INFORMATION >
DOOR
Removal and Installation of Door Weatherstrip
INFOID:0000000001327876
REMOVAL
1. Remove the mounting bolts of the check link on the vehicle. Refer to BL-132, "Removal and Installation of
Front Door" or BL-133, "Removal and Installation of Rear Door".
2. Remove the weatherstrip clips and remove weatherstrip.
INSTALLATION
Install in the reverse order of removal.
1. Weatherstrip 2. Clip
PIIA6024E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C