2008 GREAT WALL FLORID belt

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual220
3. Airbag system warning lamp is always on
2Airbag system warning lamp is always on
Inspection
status
Airbag system warning lamp is always on
Possible
causes
• Battery power supply is insufficient
• ECU internal malfunction
• Combination meter airbag warning lamp malfunction
• ECU plug is improperly connected
• Combination meter plug poorly contacted
• ECU power supply fuse circuit broken or poorly contacted
• Poor ECU plug terminal connection
• Poor wire harness contact between the ECU plug terminal and the ground
• Driver side or front passenger side airbag circuit malfunction
• Driver side and front passenger side preload seat belt malfunction
Diagnostic procedures
When starting inspection, please first use the specially designed diagnostic instrument (X - 431 diagnostic scanner)
and the ECU to diagnose the communication and determine the causes of malfunction. If communication fails,
please perform the following inspections
StepsInspection Operation
1
Examine the battery
• Check the battery voltage
• Is the voltage higher than 9 V?
Examine the charging/discharging system, and then go to step
5
YesGo to the next step
NoBattery power supply
is insufficient
2
Examine the conducting state of the wire harness between the
ECU unit and combination meter
• Set the ignition switch to the LOCK position
• Disconnect the battery's negative terminal
• Open the dashboard base
• Disconnect the instrument cluster connectors
• Connect the battery's negative
• Set the ignition switch to the ON position
• Check whether the corresponding connector terminal's
voltage is 12 V (power supply and meter connection)
YesGo to the next step
NoCheck the circuit, and then
go to step 5 after it is fixed
3
• Set the ignition switch to the LOCK position
• Check if the meter connector's corresponding terminal and
diagnostic interface's corresponding terminal are conducting
(diagnose the K wire's two ends)
YesGo to the next step
NoRepair or replace the wire
harness.Then go to step 5
4
B e s u r e t o d i s c o n n e c t t h e b a t t e r y ' s n e g a t i v e c a b l e a n d
maintain for at least 1 min
• Disconnect the ECU connector
• Disconnect the instrument cluster plugs
• Are the ECU connector terminal 25, 10, 46, and instrument
cluster's connectors conducting?
YesGo to the next step
NoReplace the wire harness,
and then go to step 5
5
Remove the ECU to check whether the terminal is in good
condition. Is the short-circuiting bar broken?
YesReplace the ECU
NoReconnect the ECU connector,
and then go to the next step

Downloaded from www.Manualslib.com manuals search engine 221Airbags
StepsInspection Operation
6
Check and make sure the malfunction symptom does not
appear again after they are repaired
• Set the ignition switch to the LOCK position
• Disconnect the battery's negative cable and maintain for at
least 1 min
• Connect all of the ECU plugs
• Connect the airbag subassembly plugs at the driver side
• Connect the airbag subassembly plugs at the passenger side
• Connect the driver and passenger side preload seat belt plugs
• Connect the clock spring plugs
• Connect the battery's negative cable
• Set the ignition switch to the ON position
• Does the airbag warning lamp work properly?
Yes
After the malfunction
is removed, explain the
maintenance procedure
to the client
No
Recheck the malfunction
symptom, if the malfunction
happens again, repeat
the repairing procedures
starting from the first step
4. Internal malfunction
Type
code 0D
Trouble
code >80
SRS airbag system unit internal malfunction
Detecting
conditions
Warning
• This malfunction's diagnosis requires a trouble code not to be shown prior to inspection. Use a DTC
to perform inspection. Performing this malfunction detection might cause operator injury or system
damage due to incorrect operation. Therefore, before inspection, please properly prepare.
• SRS airbag system electronic control unit circuit internal malfunction
Possible
causesSRS airbag system unit internal malfunction
OperationReplace the SRS airbag system unit. Refer to airbag system and SRS airba\
g system unit removal and installation
5. Power supply
Trouble
code 12
and 42
The SRS airbag system electronic control unit's power supply voltage is \
out of the standard range
Detecting
conditions
Warning
• This malfunction's diagnosis requires that a trouble code not be shown prior to inspection. Use a
DTC to perform inspection. Performing this malfunction detection might cause operator injury or
system damage due to incorrect operation. Therefore, before inspection, please properly prepare.
• Voltage of the SRS airbag system unit's 5 and 6 connector pins is lower than 9 V
Possible
causes
• Battery voltage too low
The wire harness between the battery and SRS airbag system electronic control unit has a
malfunction
Diagnostic procedures
StepsInspectionOperation
1
Inspect the battery
Measure the battery voltage
Is the voltage higher than 9 V?
YesGo to the next step
NoBattery's voltage too low. Inspect
the charging/discharging system
2
Inspect the wire harness between the battery and the fuse box
Take out the fuse box making sure not to loosen the connector,
and set the ignition switch to the ON position
Is the fuse box's two corresponding terminal stub voltage higher
than 9 V?
YesGo to the next step
NoInspect and repair
the wire harness

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual222
StepsInspectionOperation
3
Inspect the wire harness between the fuse box and SRS airbag
system unit connectors
Warning
If not handled properly, the airbag module and stretch tension
type seat belt may open or tense up, causing serious operator
injury. Therefore, before performing maintenance, please read
the maintenance warnings carefully.
See also airbag system maintenance warning
Set the ignition switch to the "LOCK" position
Loosen the battery's negative cable and wait for at least 1 min
Take out the steering column housing
Loosen the clock spring connector
Take out the glove box (with the front passenger side airbag
module)
Loosen the front passenger side airbag module connectors
Take out the dashboard base
Loosen all the SRS airbag system unit connectors
Install the battery's negative cable, and set the ignition switch to
the ON position. Is the airbag system unit's 25 and 11 connector
pin voltage higher than 9 V?
YesGo to the next step
NoReplace the wire harness
4
Set the ignition switch to the "LOCK" position
Loosen the battery's negative cable and wait for at least 1 min
Take out the left side inner decoration board
Disconnect the SRS airbag system unit switching connectors
Install the battery's negative cable, and set the ignition switch
to the ON position. Is the voltage of the switching connector's
corresponding pin and ground higher than 9 V?
Yes
[Current trouble code]
Replace the SRS airbag system
unit
See also SRS airbag system
SRS airbag system unit
removal/installation
[History trouble code]
Fault diagnosis complete
NoReplace the wire harness
6. Driver side malfunction
Type
code 02
Trouble
code
01, 02, 03
Driver side airbag malfunction (resistance too low or too high, short c\
ircuit grounded, etc)
Detecting
conditions
Warning
• If it's not handled properly, the airbag module and stretch tension type seat belt may open or tense
up, causing serious operator injury. Therefore, before performing maintenance, please read the
maintenance warnings carefully.
See also airbag system maintenance warning
If there is a driver side front airbag
• The resistance between the terminal stubs of the SRS airbag system unit connector is out of the
specified range
Wire harness related SRS driver side airbag is short or open circuited
Pos-
sible causes
• Driver side airbag module malfunction
• Clock spring internal malfunction
• Connector malfunction between the clock spring and SRS electronic control unit
• The wire harness between the clock spring and the SRS electronic control unit circuit is broken or
short circuited
• SRS driver side airbag generator connectors are improperly connected

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual224
StepsInspectionOperation
7
Inspect the clock spring
Take the clock spring off
See also airbag system and clock spring removal/
installation
Inspect the clock spring
See also airbag system and clock spring inspection
Check the clock spring. Is it normal?
NormalGo to the next step
Abnormal
Replace the clock spring
See also airbag system and clock
spring removal/installation
8
Check the wire harness between the clock spring and
SRS electronic control unit
Set the ignition switch to the "LOCK" position
Loosen the battery's negative cable and then wait for at
least 1 min
Take the glove box off (with the front passenger side
airbag)
L o o s e n t h e f r o n t p a s s e n g e r s i d e a i r b a g m o d u l e
connectors
Take out the dashboard base
Loosen all the SRS airbag system unit connectors
Check the wire harness of the connectors' terminal
studs between the SRS electronic control unit and the
clock spring to see whether they have the following
problems.
• Ground
• Short connected with the power supply
• Open circuit
Is the above wire harness normal?
Normal
Replace the driver side
airbag module
See also SRS airbag system
Driver side airbag module
removal/installation
AbnormalReplace the wire harness
7. Front passenger side malfunction
Type code 02
Trouble code
01, 02, 03
Front passenger side airbag module (resistance too low or too high, sho\
rt circuit, or grounded)
Detecting
conditions
Warning
• If not handled properly, the airbag module and stretch tension type seat belt may open or tense up,
causing serious operator injury. Therefore, before performing maintenance, please read the mainte-
nance warnings carefully.
See also airbag system maintenance warning
If there is a front passenger side airbag
• The resistance between the SRS airbag system unit connector's 3 and 4 pin is out of the specified
range
• The wire harness between the SRS airbag system unit connector’s 3 and 4 pins is short-circuited
• The SRS airbag system unit connector's 1 and 2, and 3 and 4 pins are open-circuited, if there is no
front passenger side airbag
Possible
causes
• Front passenger side airbag module malfunction
• Connector between the front passenger side airbag module and the SRS airbag system electronic
control unit malfunction
• Connectors between the SRS airbag system unit and the grounded point malfunction
• Circuit between the front passenger side airbag module and the SRS airbag system electronic control
unit is broken or short circuited
• Circuit between the SRS airbag system unit and the grounded point is broken or short circuited
• SRS airbag system unit malfunction

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual226
Vehicle Collision Diagnostics
Whether the airbag is deployed or not, vehicle collision diagnostic and maintenance must be conducted
according to the following procedures.
1. Check the SRS-ECU diagnostic signal
(a) Connect the diagnostic connector (X-431 diagnostic scanner).
(b) Read the diagnostic result with the X-431 diagnostic.
Caution: Due to impact, and when the battery's power supply is insufficient, the scanner will be unable
to communicate with the SRS-ECU. At this time, use an external power supply, or make sure to
perform inspection and maintenance on the dashboard's wire harness.
2. Maintenance sequence
When the airbag is deployed, the following components should be replaced\
.
(a) Driver side airbag module.
(b) Front passenger side airbag module.
(c) SRS-ECU.
(d) Driver side and front passenger side preload seat belts.
Inspect the following components, if anything is abnormal, replace with \
a new one.
(a) Clock spring.
(b) Steering wheel, steering column, and steering lower shaft components.
Installation status of the driver side airbag module regarding the steer\
ing wheel.
(a) Inspect whether the steering wheel's noise is abnormal, for improper movement, or abnormal cleara\
nce.
(b) Inspect whether the wire harness connectors are broken and whether the terminals are deformed.
3. SRS-ECU
(a) Inspect whether the SRS-ECU housing and bracket are
sunken or depressed, cracked, deformed, etc.
(b) Inspect for broken connectors as well as deformed
terminals.
(c) Inspect the SRS-ECU bracket's installation status.
• Inspect whether the cover is sunken or depressed,
cracked, deformed, etc.
• Inspect for broken connectors as well as deformed
terminals and biting wire harnesses.
• Check whether the gas generator's housing is sunken or
depressed, cracked, deformed, etc.
• Inspect whether the arrow's direction is pointed towards
the front of the vehicle.
(d) Inspect the airbag module's installation status.
4. Inspect the driver side airbag module
5. Clock spring
(a) Inspect for broken connectors and protective tube and deformed terminals.
(b) Inspect for deformed housing.
6. Steering wheel, steering column, and lower shaft components
(a) Inspect the driver side airbag module's installation status.
(b) Inspect the steering wheel for abnormal noise, and whether the clearance is normal.
7. Inspect the wire harness connectors (dashboard wire harness).
8. Inspect whether the wire harnesses are firm. Check for damaged connectors, and deformed terminals.
Warning label
The driver side, clock spring, SRS-ECU, and front passenger side airbag, all have warning labels, with the
caution areas shown by an image. While maintenaning and using the SRS airbag, please work in accordance
with the label.Furthermore, when a label becomes damaged or dirty, please replace it with a new one.

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual232
Airbag’s Diagnostic Methods Without a Diagnostic Scanner
Airbag indicator lamp warning
Check the airbag ECU connectors for looseness, check for warnings after correct installation.
Inspect whether the clock spring is conducting
Go to a professional maintenance station to perform inspection
Disconnect the front passenger side seat belt pretensioner wires and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Disconnect the driver side seat belt pretensioner wires and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Disconnect the front passenger side airbag line and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
D i s c o n n e c t t h e d r i v e r s i d e a i r b a g l i n e a n d replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Check whether the alarm continues after replacing the clock spring
No
No
No
No
NoNo
Yes
Yes

Downloaded from www.Manualslib.com manuals search engine 233Vehicle Body
Front Door Lock Assembly ...............................................234
Rear Door Lock Assembly ................................................237
Trunk Door Lock Assembly ...............................................239
Wiper Arm and Vent Panel Assembly ...............................240
Front & Rear Window Glasses .........................................241
Dashboard ........................................................................\
242
Cooling Unit ......................................................................246
Front Door Assembly ........................................................248
Rear Door Assembly.........................................................251
Trunk Door Assembly .......................................................254
Front Bumper....................................................................256
Rear Bumper ....................................................................259
Seat Belt ........................................................................\
...262
Seats ........................................................................\
........266
Sunroof Assembly.............................................................268
Vehicle Body

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual262
Seat Belt
Components
Front seat belt removal
1. Remove the end piece hood.
Remove the end piece hood under the seat belt, and expose
the seat belt lower mounting bolt.
Rear seat belt guide ring
Rear seat belt retractor
Seat belt lower mounting bolt
Front seat belt retractor
Front seat belt guide ring
Seat belt lower mounting bolt
Vertical adjuster mounting bolt
Body B-pillar sheet metal
Vertical adjuster
Guide ring mounting bolt
Guide ring
Woven band
Retractor
Seat belt retaining end piece
45±5
Seat belt lower mounting bolt
N·m
45±5
45±5
45±5
45±5
45±5
45±5
: Specified torque
45±5