2008 GEELY MK ABS

(9) Repeat the steps above, replace 1 or 2 bolts
Tips:
Only replace 1 bolt if 2 bolts are needed to be replaced.bolt
Adjustment
value
15'
30'
45'
1°00'Location bolt
AAdjusting bolt
BC
1 point
2 point12121211.
11.
11 .Front Suspension SystemFront Wheel Alignment4-45 Refer to the table below to fix the correct adjustment if the camber is out of spec, then select the bolts for camber
adjustment.
Notice: Tighten the adjustment nuts with washer and new nuts. (4) Mount 2 nuts temporarily.
(5) Adjust the camber angle by pushing or pulling the underside
of shock absorber in the direction of required adjustment.
(6) Tightening the nuts
Torque: 132N.m
(7) Mounting the front wheel
Torque: 103N.m
(8) Check the camber
Tips:

Adjust the camber to the median of spec.
Adjustment value of positioning the bolts: 6' ~ 30'.
(0.1° ~ 0.5°)Adjusting bolt-

Front Suspension SystemFront Strut Assembly4-46Section 4 Front Strut AssemblyReplacement1. Remove screen wiper arm cover
2. Remove right screen wiper
3. Remove left screen wiper
4. Remove hood and seals of vehicle neck
5. Remove upper right ventilation shield of vehicle neck
6. Remove upper left ventilation shield of vehicle neck
7. Remove the wiper linkage assembly of windscreen
8. Remove the hood of vehicle neck
(1) Remove the bolt and 2 clips, disconnect the harness
(2) Remove the hose and harness (wiper)
(3) Remove the 8 bolts of ventilation shield of vehicle neck
9. Remove the front wheel
10. Remove the brake hose
(1) Remove the bolts, brake hose and the clamp of ABS sensor
harness from the shock absorber bracket (with ABS)
(2) Remove the bolts and brake hose from the shock absorber
(without ABS)
11. Remove the front shock absorber with helical spring
(1) Remove the shock absorber from knuckle after remove the two
nuts and bolts.
(2) Remove the front shock absorber with helical spring, remove
the three bolts mounting suspension bracket
12. Fix the front shock absorber with helical spring
(1) Mount the two bolts and one bolt onto the bracket of shock
absorber underside, and fix it onto the vise
(2) Hold down the helical spring
Notice: Don't use the impact wrench which can damage the
special tool-

Front Suspension SystemFront Strut Assembly4-4713. Remove the duct cover of the bracket for left front suspension
Remove the end cap from the bracket of suspension
14. Remove the front bracket after removing the nuts of left front
shock absorber
Hold it by the two nuts and a screwdriver or analogue, then
remove centre nut
Notice: Don't damage the stud of suspension bracket.
15. Remove the bracket assembly of the left front suspension
16. Remove the seals of bracket dust hood for left front suspension
17. Remove the left upper front helical spring seat
18. Remove the left upper front helical spring insulator
19. Remove the left front helical spring
20. Remove the left front spring bumper
21. Remove the left front shock absorber assembly bumper
22. Check the left front shock absorber assembly
Check the abnormal resistance and noise in the operation by
compressing and extending the pushrod, replace it if abnormal.
23. Mount the left front shock absorber assembly
24. Mount the left front spring shock absorber pad
25. Mount the left front helical spring
(1) Compress the helical spring with special tool
Notice: Don't use the impact wrench which may damage the
special tool
(2) Load the helical spring into the shock absorber
Attention: tighten the helical spring lower side to the gap of
spring lower seat.
26. Mount the left upper front helical spring insulator
Mount the upper insulator, mark " "toward vehicle outside.
27. Mount the upper seat of left front helical spring
Mount the upper seat, mark " " toward vehicle outside-

Front Suspension System-Front Strut Assembly4-4828. Mount the dust seals of left front suspension bracket
29. Mount the left front suspension bracket sub-assembly
30. Mount the front bracket onto the left front shock absorber nuts
(1) Hold the bracket by two bolts and a screwdriver or analogue.
Mount the new centre nut
Torque: 33N.m
Notice: DonÕt cause damage to the stud of suspension bracket.
(2) The special tool for remove
(3) Apply the multipurpose grease onto the suspension bracket
31. Mount the dust cap of left front suspension bracket
32. Mount the front stud assembly
(1) Mount the #2 suspension bracket
(2) Mount the front stud assembly by three nuts
Torque: 39N.m
(3) Mount the shock absorber onto the knuckle
(4) Film the engine oil onto the thread of two nuts
(5) Mount the two bolts and nuts
Torque: 132N.m
33. Mount the brake hose
Torque: 29N.m
34. Mount the front wheel
Torque: 103N.m
35. Mount the outside cover of vehicle neck
(1) Mount the outside cover of vehicle neck by 8 bolts
Torque: 5N.m
(2) Connect hose and harness (screen wiper)
(3) Mount the harness by bolts and two clips
36. Mount the linkage assembly of windshield wiper
37. Mount the ventilation hood of left vehicle neck
38. Mount the ventilation hood of right vehicle neck
39. Mount the engine hood and seals of vehicle neck
40. Mount the left front wiper arm
41. Mount the right front wiper arm
42. Check and adjust the front wheel alignmentMulti-purpose grease

Component ViewUpper washer
Left rear
helical spring
Lower washer Rear shock absorber assembly Right rear helical spring
Left rear helical spring
Lower washer829.09849Chapter 6 Rear Suspension SystemSection 1 Rear Suspension SystemLoad-sensing valve
bracketRear supension crossmemberRear Suspension System-Rear Suspension System4-54specified torqueN.
m :With ABS
Side slip control sensor wire
Washer
Clip Brake hose
Brake hoseNon-reusable parts

I. Rear suspension structure description This model uses strut independent rear suspension with stabilizer bar.
Rear suspension consists of the parallel front and rear double transverse arms, trailing rod, rear stabilizer bar
and rear strut assembly. The shock absorber and cone coil spring are arranged eccentrically.
See the table below for the major technical parameters of the rear suspensionII. Symptom Table Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.Suspected Area
1. Tires (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Hub bearing (Worn or damaged)
4. Suspension parts (Worn or damaged)
1. Vehicle (Overloaded)
2. Spring (Stiffness small)
3. Shock absorber (Worn)
1. Tire (Worn or improperly inflated)
2. Wheel (not within specification)
3. Shock absorber (Worn)
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Shock absorber (Worn)
4. Wheel (not within specification)
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Shock absorber (Worn)
4. Suspension parts (Worn or damaged)Symptom
Off track
Body descent
Sways
Rear wheel shimmy
Abnormal tire wearRear Suspension System-Rear Suspension System4-55Item
Shock absorber operating cylinder diameter /mm
Shock absorber piston rod diameter/mm
Shock absorber stroke /mm
Camber
Toe in/mm
Remark: Wheel alignment parameter is at free loadParameter
38
12.4
250
-0°56' ± 45'
3 ± 3

Section 3 LH/RH Rear Suspension Coil SpringReplacement1. Remove rear wheel
2. Remove the wire of the wheel speed sensor(with ABS)
(1) Remove the connector of wheel speed sensor.
(2) Remove bolts and wheel speed sensor from rear axle
frame.
Notes:
Remove the right sensor wire by using same process as left.
3. Remove the load-sensing valve bracket (without ABS)
Remove two nuts and load-sensing valve bracket from the axle
bracket
4. Remove the proportioning valve and rear right brake tube
(1) Remove the proportioning valve and rear right brake tube by
the special tool
(2) Remove the clips
Notes: Don't reuse the clips
5. Remove the proportioning valve and rear left brake tube
Notes: use the same operations of the proportioning valve and
rear right brake tube to remove #3 rear brake tube.
6. Remove right parking brake cable assembly
Remove nuts and right parking brake cable assembly
assembly from rear axle frame
7. Remove left parking brake cable assembly
8. Loose the rear axle assembly
Loose two 2 boltsRear Suspension System-LH/RH Rear Suspension Coil Spring4-57

9. Remove the left rear shock absorber assembly
(1) Lift the rear axle at left sustainer by lifting jack
(2) Remove nuts, washers and left rear shock absorber assembly
10. Remove right rear shock absorber assembly
Notes: Remove right rear shock absorber assembly by using same
operations as left.
11. Remove left rear helical spring
Slowly lower lifting jack, remove helical spring and upper pads
and lower pads
12. Mount the left rear helical spring
(1) Mount the upper pad, let gap right on the helical spring.
(2) Mount lower pad, let and load the left helical sprig into the rear
axle.
13. Temporarily tighten the left rear shock absorber assembly
(1) Mount the left rear shock absorber onto rear axle frame when
lift jack.
(2) Temporarily tighten nut and washer.
14. Temporarily tighten the right rear shock absorber assembly.
Notes: Mount the right assembly by using same operations as left.
15. Mount right parking brake cable assembly
Mount right parking brake cable assembly by nuts
Torque: 5.4 N.m
16. Mount left parking brake cable assembly.
Tips: Mount the right assembly by using same operations as left.
17. Mount the proportioning valve and rear right brake tube
(1) Connect the brake hose with brake tube by special tool.
Torque: 1 5 N.m
(2) Mount clipsRear Suspension System-LH/RH Rear Suspension Coil Spring4-58