2008 GEELY MK wheel bolts

Brake System -Front Brake Disc4-9827. Install the support piece of the front brake pad.
Remove the two support pieces of the brake pad from the front disc brake cylinder support.
28. Install the brake lining block component.
Note:
When replace the abrasion brake lining block, replace the muffle
pad simultaneously.
(1) Apply the disc brake lube on both sides of all muffle pads
(2) Install muffle pads on all brake lining blocks.
(3) The abrasion indicator face upwards. Install a inner brake
lining block, then install a outer lining block.
Note:
Don't apply the oil or lube on the friction surface of the brake pad and brake disc.
29. Install the front disc brake wheel cylinder.
(1) Install the front disc brake wheel cylinder with two bolts.
Torque: 34N.m
(2) Install the new washer and tube with bolt.
Torque: 30N.m
Tips: Fasten the tube in the lock hole of the brake wheel
cylinder reliably.
30. Add the brake fluid to the storage tank.
31. Discharge the air in the brake cylinder.
32. Discharge the air in the brake pipeline.
33. Check the level height in the storage tank.
34. Check the brake fluid whether there is any leakage.
35. Install the front wheel.
Torque: 103N.m

Brake System -Parking Brake System4-107Adjustment1. Remove the rear wheel.
2. Adjust the clearance of the brake shoe.
3. Install the rear wheel.
Torque: 103N.m
4. Check the stroke of the parking brake extension rod.
Pull the parking brake extension rod, and count the number of sound.
Parking Brake Extension Rod Stroke: Pull with 196N force till 6-9 clicks.
5. Adjust the stroke of the parking brake extension rod.
(1) Remove the glove box cover.
(2) Turn #1 adjustment nut inhaul cable till the stroke is ok.
(3) Install the glove box cover.Parking Brake System The table below can help you find out the possible failure reasons. The number means the possible sequence
of the reasons. Check the parts, and replace the corresponding parts if necessary.Parking Brake Tension Rod Component1. Remove the accessories of the console.
2. Remove the middle console.
3. Remove #1 adjustment nut wire.
Remove #1 adjustment nut wire.
4. Remove the accessories of the parking brake extension rod.
(1) Remove the connector of the parking brake extension rod
switch.
(2) Remove the two bolts, and remove the parking brake exten
sion rod.
5. Remove the parking brake switch component.
Remove the screw and parking brake switch component.Suspected location
1. The stroke of the parking brake extension rod is misadjusted.
2. The parking brake inhaul cable is trapped.
3. The clearance of the parking brake shoe is misadjusted.
4. The parking brake lining is cracked or deformed.
5. The return or extension spring is damaged.Symptom
Brake is blocked.#1 adjustment nut inhaul cable

Brake System -Parking Brake System4-1092. Remove the middle console.
3. Loosen #1 inhaul cable adjustment nut.
Remove #1 inhaul cable adjustment nut.
4. Remove the front floor extension rod.
Remove the two bolts to take out the front floor extension rod.
5. Remove the front exhaust pipe component.
6. Remove #2 front floor hot pad.
Remove the two bolts to take out the front floor hot pad.
7. Remove #3 parking brake inhaul cable component.
(1) Remove the four bolts to remove # 3 parking brake inhaul cable from the body.
(2) Remove #3 parking brake inhaul cable component from the parking brake balancer, and remove the inhaul
cable component.
8. Remove the rear wheel.
9. Remove the accessories of the brake drum.
10. Remove the front brake shoe.
11. Remove the left rear automatic adjustment rod.
12. Remove the rear brake shoe.
13. Remove parking brake inhaul cable component.
Remove the bolt, and remove parking brake inhaul cable
component from the baseboard.
14. Install parking brake inhaul cable component.
(1) Install parking brake inhaul cable component on the parking brake inhaul cable balancer.
(2) Fasten parking brake inhaul cable with four bolts.
Torque: 5.4N.m

Brake System -Parking Brake System4-11015. Install #3 parking brake inhaul cable component.
Fasten #3 parking brake inhaul cable component to the baseboard.
Torque: 7.8N.m
16. Apply the heat-resistant lube.
17. Install the brake shoe.
18. Install the return spring of the brake shoe.
19. Install the left rear brake automatic adjustment rod.
20. Install the front brake shoe.
21. Check the installation of the brake drum.
22. Install the accessories of the brake drum.
23. Adjust the clearance of the brake shoe.
24. Install the rear wheel.
Torque: 103N.m
25. Fasten #1 adjustment nut wire temporarily.
Install #1 adjustment nut wire.
26. Install #2 front floor hot pad.
Fasten #2 floor hot pad with two bolts.
Torque: 5.5N.m
27. Install the front exhaust pipe component.
28. Install the front floor extension rod.
Install the front floor extension rod with two bolts.
29. Check the stroke of the parking brake extension rod.
30. Adjust the stroke of the parking brake extension rod.

III. Wiper switch assemblyReplacement
1. Detach steering wheel assembly
(1) Disconnect the main power source of the vehicle.
(2) Remove the passenger SRS module assembly, and cautiously put it in a safe place.
(3) Loosen steering wheel lock-bolts and remove the assembly.
2. Remove wiper switch (1) Disconnect the connector.
(2) Remove the 2 tapping screws that are for mounting the wiper switch, take out the wiper switch from the
bracket of the combination switch.IV. Washer nozzleAdjustment
1. Inspect washer nozzle
(1) Start the engine, check if the position where the washer fluid from the nozzle sprays the windshield is in
the upper center wiped by the blades.
(2) Change the height (left/right) of the nozzle hole to adjust the point where washer fluid sprays the windshield.Wiper and Washer System -Replacement and Adjustment5-25

1) Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery from
the vehicle.Notice
Work must be started 60s after removal of the battery.Notice
When the connector is not connected, the terminals of the driver airbag assembly will be short circuited
automatically, preventing the airbag from being deployed unexpectedly. If the airbag is deployed unexpectedly,
the deployed surface should face up. It should be kept on a flat surface without any other items on it. 2) The airbag assembly shall be deployed according to the following procedures.
Driver airbag assembly
a. Remove the driver airbag assembly from the vehicle.
b. Prepare two 6m plus wire harnesses for deployment, connect
the other two ends to avoid unexpected deployment in case
of static electricity (see the figure below).Notice
The above-mentioned procedures can prevent the unexpected deployment due to static electricity and shall
therefore be performed strictly.Deployed Harness
Short Circuit Point
More than 6mInsulation tapeDeployment
wire harness
Short circuit
locationDriverÕs airbag
moduleAirbag assembly
Deployed
harness c. Touch the body of the vehicle with hands for static electricity elimination.
d. Cut off the wire harnesses of the driver airbag assembly and
connect them with the two wire harnesses for deployment,
and make sure to wrap up the connecting location with
insulating tape for insulation (see the figure on the right).
f. Pass the deployment wire harness of the driver airbag
assembly through an old tire with rim, and fix upwards the
driver airbag assembly by means of the wire connected to
the bolts, etc (see the figure on the right). e. Install the unused bolts to the inside bolt of the driver airbag assembly,and tie a thick metal wire securing
the wheel rim.5-70SRS (Supplemental Restraint System)-
SRS-General Information

Interior & Exterior Trim and Accessory -Front Seat Belt6-8VI. Attentions:
1. Before mounting, you must check if the product is damaged, cracked or rusted.
2. Place the retractor on the vertical position before pulling out the strap. Check if the strap can be easily pulled
out and rotated and the retractor can be locked.
3. When installing a pretensioning seat belt, check if the emitter head pin deflects and is rusted, etc. The emitter
in the pre-tensioning seat belt can work for 15 years.
4. Check if the buckle lock and connection piece comply with the connection of the car. And check if the buckle
can be opened easily.
5. When fitting the bolts, check if the threads on the nut of coating are clear. Those with welding slag must be
cleaned before fitting the bolts.
6. After pulling out the strap of retractor, no barrier (such as wiring harness, etc.) around the strap is allowed. If
there is, it is necessary to get rid of the barrier to ensure the force of retractor and that the strap is not scratched.
VII. How to handle with scraped seat belt
Tips:
Scrap seat belt provided with pre-tensioner, you have to trigger the pre-tensioner taking the following steps.
1. Check if the storage battery is above 12 V on its positive and negative poles;
2. Check the energizing tool;
Warning:
When energizing the pre-tensioner of seat belt, be sure to use dedicated energizing tool for the pre-tensioner
of seat belt.
3. Connect the special tool with the storage battery and also connect
the red clip on the special tool with the positive terminal of the battery
and connect the black clip with the negative terminal of the battery;
4. If the front seat belt is on the car body and is not taken off,
disconnect the joint of the pre-tensioner of seat belt;
5. Connect the yellow joint of the special tool with the joint of the
pre-tensioner of seat belt;
6. At 10 meter away from seat belt, use a special tool to trigger theAbove 10 meterpre-tensioner of seat belt.
Warning:
a. Ensure that there be no people within 10 meters from the seat
belt;
b. If the seat belt has already been taken down from the car, it is
necessary to cover it using the car wheel with tire to avoid injury.
c. When triggering, explosion will emit loud sound. So it shall be
done outdoors without disturbing local community.
d. When you hold the triggered seat belt, be sure to wear gloves
and goggles.
e. After you have finished the operation, you must wash your hands.
f. Do not pour water, etc. to the energized seat belt pre-tensioner.
7. Place the already triggered seat belt into the ethylene bag and tighten it as you do with other articles.
Warning:
a. Do not dispose untriggered seat belt at will.
b. When the pre-tensioner of seat belt is triggered, the seat belt assembly would be very hot. Therefore, you
cannot touch it until at least 30 minutes after it is triggered.