2008 GEELY MK sunroof

Chapter 2 Usage and Maintenance of MK SeriesSection 1 Usage of MK Series1. Instrument Panel Overview1.Instrument Panel Outlet Vent
2. Instrument Panel
3.Upper Glove Compartment
(Front Passenger Airbag Cover)
4.Sunshade
5.Dome Light And Sunroof
Switch
6.Inside Rearview Mirror
7.Glove Box
8. Power Window Regulator
Switch
9. Manual Transmission Shift
Lever Or Automatic Transmis-
sion Shift Lever
10.Parking Brake Control Lever
11.Engine Hood Release Handle
12.Power Window Lock
13.Power Door Lock Switch1.Left Combination Switch
2.Right Combination Switch
3.Display
4.Audio
5.Short-Distance Odometer
Adjustment Button
6.Instrument Panel Brightness
Adjustment Switch
7.Hazard Warning Light
8.A/C Control Panel
9.Ash Tray
10.Defroster Switch
11.Cigarette Lighter
12.”A/C“ Switch
13.Ignition Switch
14.Tilt Steering Adjustment
Handle
15.Theft-Deterrent Indicator
16.Power Outside Rearview
Mirror Control SwitchUsage and Maintenance of MK Series - Usage of MK Series2-6

IV. Location of light systemRear reading light
High-mount stoplight
Rear combination light
Rear license light
Front reading light ( power sunroof )
Side turn light
Front foglight Front combination lightRear Radar
SensorLight System -Light System Introduction5-27

4. Danger alarm lamp switch assembly
Check whether danger alarm lamp switch is connected.
Check whether two terminals are connected when switch works.
If it doest not meet stipulation, replace the switch.
5. Door lamp switch (on fastener)
Check whether door lamp switch is connected
When switch works, check whether connection is established
between terminal and bodywork earthing.
If it doest not meet stipulation, replace the switch.
6. Trunk lamp switch assembly
Check whether trunk lamp switch is connected
When switch works, check whether connection is established between terminal and bodywork earthing.
If it doest not meet stipulation, replace the switch.
7. Front reading light assembly (with power sunroof)
Check whether terminals of indoor roof lamp assembly are
connectedSwitch motion Testing terminal Status
ON 1-2 ON
OFF 1-2 OFFSwitch motion Testing terminal Status
ON (door is closed) 1- GND ON
OFF (door is not closed) 1- GND OFF
Switch motion Testing terminal Status
ON 1- GND ON
OFF 1- GND OFFSwitch motion Testing terminal Status
ON 1-2 ON
OFF 1-2 OFF If it does not meet stipulation, replace roof lamp or switch.
8. Rear reading light assembly
Check whether back row reading light assembly is connected
When switch works, check whether two terminals are connectedSwitch motion Testing terminal Status
ON 1- 2 ON
OFF 1- 2 OFF If it doest not meet stipulation, replace the switch.211Light System -Light System Malfunction Inspection5-33

Chapter 17 Moonroof Assembly (Optional)Component ViewII. Inspection of sunroof Troubleshooting formSunshade sub-assy Sunroof motorBracket sub-assy.Sunroof frameSunroof glass bracketSunroof glass sealSunroof glassInterior & Exterior Trim and Accessory -Moonroof Assembly (Optional)6-40Possible causes
1. Power relay
2. Instrument fuse
3. Sunroof switch
4. Sunroof lock switch
5. Sunroof motor
6. Sunroof guide rail
7. Wire harness
1. Sunroof lock switch
2. Sunroof motor
3. Sunroof guide rail
4. Wire harnessSymptom
Sliding sunroof system doesn't work.
Sling sunroof system gets stuck (e.g.
foreign matter like gravel caught in motor)

Interior & Exterior Trim and Accessory -Moonroof Assembly (Optional)6-41III. Removal and installation of sliding sunroof1. Remove the roof panel trim
(For more information, see "removal and installation of roof panel trim".)
2. Remove the ceiling lamp
(For more information, see "removal and installation of roof panel trim".)
3. Remove the sunroof glass sub-assembly
a. Unfix the screw by use of a box spanner;
b. Pull the glass upward and then take it out.
4. Remove the sunroof motor
Caution
Make sure the sunroof is completely closed before removing the sunroof motor.
a. Disconnect the connector;
b. Unfix the bolt and then remove the sunroof motor.
5. Remove the sunroof bracket sub-assembly
a. Detach water pipe;
b. Unfasten the retaining bolts around the sunroof bracket sub-assembly;
c. Take out the sunroof bracket sub-assembly.
6. Remove the sunshade sub-assembly
Slide the sunshade backward and then take it out.
7. Remove the sunroof drive cable and the sunroof guide rail;
8. Install in reverse order of removal.
Caution
Check if the sunroof is waterproof after installation.
If a water leak is detected, readjust the sunroof.
For more information on the electrical part of sunroof, see the chapter on electrical part of this manual.