2008 GEELY MK window

Interior & Exterior Trim and Accessory -Rear Door Interior Trim6-326. Remove the rear left window and the guide slot of rear left window;
Tip:
Insert the duster cloth into the interior plate of door to prevent
scratch on glass.
a. Remove the left rear window;
b. Remove the screws and the 2 bolts;
c. Remove the guide slot of rear left window.
7. Remove the rear left corner window;
8. Remove the assembly of left-rear window regulator.
a. Disconnect the connector;
b. Remove the 4 bolts and the assembly of left-rear window
elevator.
Tips:
After removal of bolts, rear left window regulator may fall to
cause damage.
Tip:
Remove the rear left window regulator through the manhole.

(2) Front FenderFront fender plays a role in front wheel apron and rotect person safty.And at the same tirne,if also woork as vehicle
styling parts.
For the match relationship between the front fender & engine hood and the front door, see Fig. 5-9.Fig. 5-9 Front Fender related to surrounding parts
A) With Engine Hood (4mm¡À1mm)
B) With Front Door (5mm¡À1mm)(3) Door Assembly Doors have LH/RH front door and rear door.
The door uses hinge gemel with limiting device, which is an open structure.
The door includes door outside plate, door inside plate, bumper and hinge reinforced plate etc.
The door has a complex structure, which is a movable component on the body. It helps the passengers get on/
off the vehicle and form an enclosed cabin with the main structure and the relevant parts. Meanwhile, the doors
are used frequently, so there is high requirement on their reliability and durability.
The outside/inside plate is molded by one complete steel sheet, which can improve the stiffness and precision.
In order to improve the safety when the vehicle is collided from the side, four doors are equipped with door
bumpers.
As shown in Fig. 5-10 and Fig. 5-11, the door assembly is made up of outside plate assembly and inside plate
assembly.Fig. 5-10 Front Door
1. Front door inner panel 2. Left front door inner reinforced panel 3. Front door window opper rail 4. Door lock reinforced panel
5. Left front door inner plate cross beam 6. Front door outer panel 7. Door bumper assembly
8. Front door upper hinge assembly 9. Front door lower hinge assembly 10. Hinge reinforced panel assemblySurvey -Body Structure7-7Engine hood
Front fenderFront door
Front fenderA
B12345678910

3. External Force Having an Angle with Vehicle Centerline (Fig. 5-15)Body Repair -Body Damage Forms and requirements For Repair7-10Fig. 5-15 External Force Having an Angle with Vehicle Centerline As shown in Fig. 5-15, when the vehicle is acted by an external force having an angle with its centerline, the
force will affect the hood root and the front window side post if it is strong enough.
4. Body Side Center Acted by External Force in Upright Direction (Fig. 5-16)Fig. 5-16 Body Side Center Acted by External Force in Upright Direction As shown in Fig. 5-16, when the body side center is acted by an external force in the upright direction, check
the following positions:
a. Front window side post upper/lower installation position;
b. Side window intermediate post upper/lower installation position;
c. Side window rear post deformation;
d. Roof and frame deformation.
When the body is acted by an external force on the rear part, its damage is the same as that caused by an external
force on the front part. Check the parts in full consideration of the rear structure and feature.External ForceExternal Force

3. Body Opening Part (Back View)
A-d 1504±2.5
4
a-D 1504±2.5
C-d 1191±2.5
4
c-D 1191±2.5
f-G 1217±2.5
4
F-g 1217±2.5
e-B 1599±2.5
4
E-b 1599±2.5
h-I 1003±2.5
4
H-i 1003±2.5
(mm)
Item Description
Diameter of Hole
XYZ
A,a
Back window glass fastener installation hole
11.5¡Á8.52327.46 +/-374.49 1118.41
B,b
Rear absorber spring support hole
18 2506.99 +/-534.81 550.09
C,c Tall lamp installation hole 5 3190.8 +/-679.49 632.24
D,d Rear bumperinstallation bole 15 3202.45 +/-428.13 195.64
E,e B-pillar rear assembly mark - 1493.1 +/-672.96 812.59
F,f
Rear joint between side outer panel and roof panel
- 2310.74 +/-598.88 1106.12
G,g
Joint between side outer panel and luggage compartment
- 2816.19 +/-569.92 831.4
H,h
Joint between side outer panel and tail lmap panel
- 2987.01 +/-569.92 798.34
I,i
Rear joint between side outer panel and rear end panel
- 3327.63 +/-325.23 500.2Appendix-Body Key Dimensions7-40
Measuring
point
Value
Tolerance