2008 GEELY MK window

Centralized Controller System-
Function Inspectior5-133Chapter 12 Centralized Controller SystemSection 1 Function InspectiorI. Glass frame riser: 1. Glass frame riser may be operated to move within 60s after ignition switch is turned on or off; 60s after
ignition switch is turned off, glass frame riser cannot be operated to move;
2. Manual rise: press corresponding glass frame riser switch rise key, corresponding glass frame riser motor
works, glass frame rises, release rise key, it stops.
3. Manual fall: press corresponding glass frame riser switch fall key (hold time 300ms), corresponding glass
frame riser motor works, glass frame falls, release fall key, it stops.
4. Automatic fall: press corresponding glass frame riser switch fall key (hold time < 300 ms), corresponding
glass frame riser motor works, glass frame falls down to end; or fall down until rise key or fall key is pressed again.
Note:
During automatic fall of glass frame, if corresponding glass frame riser switch fall key is pressed down for more
than 300 ms, glass frame riser is changed to manual fall mode; if corresponding glass frame riser switch rise key
is pressed down for more than 300ms, glass frame riser stops work.
5. Remote window closing:
In case of remote protection, if a key is pressed down for more than 1s, perform glass frame riser automatic
rise action, left front, right front, left rear, right rear in turn.II. Central lock: 1. In case protection is deactivated, use a key to open left front door switch or press internal unlock switch to
open four door fasteners; close left front door switch, close four door fasteners.
2. Remote unlock /lock:
(1) Ignition switch opening
a. Press remote control unlock key to open four door fasteners;
b. Press remote lock key to close four door fasteners;
(2) Turn off ignition switch
a. Press remote unlock key to open four front door fasteners, at the same time turn light flashes once.
b. Press remote lock key to close four door fasteners, at the same time turn light flashes twice.
(3) When door is opened, press remote fastener, turn light will flash for three times, at the same time electric
horn beeps for three times.
(4) If the system is triggered in anti-theft condition, when remote unlock system exits protection state,
directional turn signal will flash for four times, at the same time, electric horn beeps for four times.
3. Automatic lock
When vehicle speed exceeds 30km/h, three doors will be closed.
4. Door lock priority
Central door lock should not act simultaneously with glass frame riser; when they conflict with each other,
central door lock acts with priority, while glass frame riser stops; after central door lock action is finished, glass
frame riser continue its work in previous condition.III. Front womdscreem wiper: After spray water signal is finished, the wiper acts twice.

Terminal No.
B1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25G
G
RY
Br
GB
GW
BLW
Br
RB
RB
YB
YB
RBL
RBL
GBL
R
RW
RW
BR
WR
BL
W
WB
BLB
R
BLB
WB
BLY
WY
RBHazard lamp power supply
Hazard lamp power supply
Dome lamp
Wiper motor (INT)
GND
GND
Right turn light and its indicator lamp
Left turn light and its indicator lamp
IG2
Wiper switch 3#Head light relay 85 #Head light relay 85 #Rear air window defrost and indicator lamp
Rear air window defrost and indicator lamp
Rear air window defrost power supply
Rear air window defrost power supply
GND
Horn relay 85 #Electric glass frame power supply
GND
GND
Fastener power supply
Right front, right rear, left rear fastener
Right front, right rear, left rear fastener
Left actuator
Front left glass regulator
Front left glass regulator
GND
Front right glass regulator
Front right glass regulator
Glass power supply
Rear left glass regulator
Rear left glass regulator
GND
Rear Right glass regulator
Rear Right glass regulator
Left actuatorConductor color Terminal definitionCReplacement ( 1 ) Remove dashboard subassembly (refer to trim)
( 2 ) Remove two bolts5-136Centralized Controller System-
Function Inspectior

Chapter 13 Door Glass Regulating and Power Door Lock ControlSection 1 Door Glass Regulating SystemI. Inspection1. Check basic function
(1) Ignition switch is turned "ON" or within 60 s after ignition switch is turned off.
a. Check when rise key of glass regulator switch is pressed, corresponding glass rises, when release, it stops
rising; when press fall key and hold it, corresponding glass falls, when release, it stops falling.
b. Check when glass regulator main control switch lock switch on driver side is pressed,except which on driver
side, other glass regulator switches do not act.
c. Automatic fall: press corresponding glass regulator switch fall key briefly,corresponding glass
regulator motor works, glass falls down to the end; or falls down until rise key or fall key is pressed again.
Notes:
During automatic glass down, if corresponding glass regulator switch fall key is pressed down and held,
glass regulator is changed into manual fall mode; if corresponding glass regulator switch rise key is pressed down
and held, glass regulator is changed into manual rise mode; if corresponding glass regulator switch rise or fall key
is pressed briefly, glass regulator stops work. Press briefly: less than 300ms; press and hold: more than 300 ms.
(2) Close window remotely.
In case setting protection remotely, if a key is pressed for more than 1s, glass regulator automatic window
rising action will be performed, implementation mode: left front, right front, left rear, right back, in the
process of window rise, only one glass regulator is permitted to act, only after glass regulator up to the top,
could the other glass riser act.
2. Glass reguelator switch on driver sideDoor Glass Regulating and Power Door Lock Control-Door Glass Regulating System5-136Glass regulator switch on driver side
Window on front passenger side
Window on driver side
Rear right window
Rear left window
Window locking switch

(1) Check conductibility of the switch.
Standard
Switch position Terminal Result
On driver side
On front passenger side
Left rear
Right rear
Window locking switchUP 12--­13 ON
DOWN12---14 ON
UP 12---5 ON
DOWN12---6 ON
UP 12---9 ON
DOWN12---10 ON
UP 12---1 ON
DOWN12---2 ON
Lock12---3 ON
Unlock12---3 OFFResult
Indicator lamp
illuminates If it does not meet stipulation, replace this switch.
(2) Check indicator lamp on glass riser switch on driver side
Storage battery may be connected with terminal of indicator
lamp directly (as shown in the figure)
Standard
If it does not meet stipulation, replace this switch.
3. Other window glass riser switches (passenger side, left rear, right rear)Door Glass Regulating and Power Door Lock Control-
Door Glass Regulating System5-137Connecting condition
Battery positive - terminal 11
Battery negative - terminal 12Other glass regulator switches

Chapter 7 Rear Window Glass (with Defrosting Heater Wire)II. Removal and Replacement of Rear Windscreen Glasses Tip:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.I. Component ViewRear right roof handleRoof trim
Rear windscreen stopperRear windscreen weather strip
Rear right C-pillar trim
Windscreen glass
weather stripHight mounted brake light assembly
Rear shelf trim Rear left C-pillar trim rear windscreen glass Rear left roof handleInterior & Exterior Trim and Accessory -Rear Window Glass (with Defrosting Heater Wire)6-20

Interior & Exterior Trim and Accessory -Rear Window Glass (with Defrosting Heater Wire)6-211. Remove the assembly of rear seatback; (Refer to "Removal and Installation of Seat")
2. Remove the interior decorative components of vehicle top; (Refer to "Removal and Installation of Interior
Decorative Components of Vehicle Top" )
3.Remove the upper decorative plate at the right-rear enclosure;
(Refer to "Removal and Installation of Interior Decorative Com-
ponents at side enclosure" )
4.Remove the assembly of high-level brake light;
(Refer to "Removal and Installation of Interior Decorative Com-
ponents at side enclosure" )
5. Remove the assembly of trunk shelf;
(Refer to "Removal and Installation of Interior Decorative Com-
ponents at side enclosure" )
6. Remove the exterior seal belt of rear window glass;
(1) Cut apart the seal belt with knife;
Tips:
Do never damage the vehicle body with knife.
(2) Pull off the cut seal belt by hand, and remove it.
7. Remove the rear window glass.
(1) Let the steel wire go through the vehicle body and the glass;
(2) Secure the wire at two ends with wood-block-kind-of objects;
(Tip: attach the protective film to the exterior surface to prevent
scratch)
(3) Pull the steel wire, and cut off the polyester urethane sticking/
sealing materials around the glass;
(4) Remove the stopper;
(5) Remove the glass with the rubber extraction.
Tips:
Separate the glass carefully to prevent scratch on paint or
interior/exterior upholsteries;
Leave as much polyester urethane sticking/sealing materials
as possible on the vehicle body during the removal of glass.
8. Clean the rear windscreen;
(1) Remove the remained stopper, waterproof layer and polyester
urethane sticking/sealing materials with the scraper;
(2) Clean the exterior glass ring with uncontaminated petroleum.
Tips:
Keep off the glass surface after cleaning it.slotslot
cut
cut
stopper
steel wire

Chapter 11 Rear Door Interior TrimI. Component ViewRear left glass guide slot Left window end cover
Rear left window
guide track Rear left corner window weather strip
Rear left window inner weather stripRear Left corner glasses
Rear left windowRear left window
outer weather strip
Rear left window regulator
assembly
Rear left door weather strip Inside handle installation
bracket
gripsPower rear window switchRear left door inside handle
Rear left door
interior trim panel6-30Interior & Exterior Trim and Accessory -Rear Door Interior Trim

6-31II. Removal and Installation of the Rear Door Interior trim Tip:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.
The removal and installation at the right side are the same as those at the left side.
1. Remove the interior decorative plate handle of left rear door;
Remove a screw with the cross-head screwdriver, and then take
off the interior decorative plate handle of left-rear door.
Tip:
Wrap the head of screwdriver with belt before using it.
2. Remove the assembly of electric-driven window regulator switch;
a. Release the grips with the straight screwdriver, and then re
move the regulator switch off the decorative plate.
b. Disconnect the switch connector.
3. Remove the interior decorative plate of left rear door;
a. Remove the screws and buckles;
b. Release the 6 buckles with the straight screwdriver, and hold
upwards the interior decorative plate of rear-left door to re
move it.
Tip:
Wrap the head of screwdriver with belt before using it.
4. Remove the interior handle of left-rear door;
Release the 2 hooks, remove the interior handle of left-rear door,
and disconnect the 2 wires off the interior handle of left-rear door.
5. Remove off the rain-proof film on the door;clip
HookHookgripsInterior & Exterior Trim and Accessory -Rear Door Interior Trim