2008 GEELY MK wheel torque

(2) Using sst, remove inner race of the left axle hub bearing from
the left axle hub sub assembly.
13. Remove front left brake disc boot
Remove 3 bolts and front left boot.
14. Remove left front axle hub bearing
(1) Place the left axle hub bearing inner race into the left axle hub
bearing outer race.
(2) Remove the left axle hub bearing from the steering knuckle
with press and sst
15. Install left front axle hub bearing
Install the new left axle hub bearing on the steering knuckle with
press and sst
16. Install front left brake disc boot
Install the front left boot with 3 bolts.
Torque: 8.3N.m
17. Install left front axle hub subassembly
Install left axle hub assembly with press and sst.
18. Install left front axle hub snap ring
Install the new left snap ring with snap ring plier.Propeller Shaft/DriveshaftFront Wheel Hub4-32 -

Propeller Shaft/DriveshaftFront Wheel Hub4-3319. Install left front shock absorber assembly
Install the front left shock absorber assembly on the left front axle
assembly with 2 sets of bolts and nuts
Torque: 132N.m
Notice:
Only coat the thread parts of the new bolts and nuts with engine
oil.
20. Install left front axle assembly
21. Install left tie rod end subassembly
22. Install left no.1 front lower suspension arm subassembly
23. Install front stabilizer
24. Install front brake disc
25. Install left front brake caliper assembly
Install the front brake caliper assembly on the steering knuckle
with 2 bolts.
Torque: 88N.
m
26. Install left front axle hub nut
Install new left axle hub nut.
Torque: 216N.m
27. Remove left front brake caliper assembly
28. Remove front brake disc
29. Check bearing backlash
30. Check axle hub deviation
31. Install front brake disc
32. Install left front brake caliper assembly
33. Install left front vehicle speed sensor (with ABS)
34. Install left front axle hub nut
Using a chisel and hammer, stake the left axle hub nut.
35. Install front wheel
Torque: 103N.m
36. Check and adjust front wheel alignment
37. Check abs vehicle speed sensor signal (with ABS) -

Replacement1. Remove front wheel
2. Remove left front brake caliper assembly
3. Remove front brake disc
4. Remove left front axle hub bolt
Using a ball joint puller and a screwdriver or similar, remove the
left axle hub bolt.
5. Install left front axle hub bolt
(1) As shown in the illustration, install the gasket and nut on the
new left axle hub bolt.
(2) Using a screwdriver or similar,hold the left axle hub subassembly,
install the left axle hub bolt by tightening the nut.
6. Install front brake disc
7. Install left front brake caliper assembly
8. Install front wheel
Torque: 103N.mPropeller Shaft/DriveshaftFront Wheel Hub4-34 The replacement of the right front axle hub subassembly is the same as that of the left one.Washer
Nut -

Propeller Shaft/DriveshaftRear Wheel Hub and Bearing Assembly4-35Section 4 Rear Wheel Hub and Bearing AssemblyComponent ViewRear Axle Hub UnitBrake Drum Assembly
specified torqueN.
m :Slip Control Sensor Wire Harness
With ABS
Left Rear Axle Hub Bolt - Non-reusable parts

Replacement1. Remove rear wheel
2. Remove rear wheel brake drum subassembly
3. Remove slip control sensor wire harness (with ABS)
4. Remove left rear axle hub and bearing assembly
Remove 4 bolts and left axle hub and bearing assembly.
5. Install left rear axle hub and bearing assembly
Install left axle hub and bearing assembly with 4 bolts
Torque: 63N.m
6. Connect slip control sensor wire harness (with ABS)
Notice:
Do not twist the sensor wire harness during connection.
7. Check bearing backlash
8. Check axle hub deviation
9. Install rear wheel brake drum subassembly
10. Install rear wheel
Torque: 103N.m
11. Check as vehicle speed sensor signal (with ABS)Propeller Shaft/DriveshaftRear Wheel Hub and Bearing Assembly4-36 -

Propeller Shaft/DriveshaftRear Wheel Hub and Bearing Assembly4-37Replacement1. Remove rear wheel
2. Remove rear wheel brake drum subassembly
3. Remove left rear wheel axle hub bolt
Using a ball joint puller and a screwdriver or similar, remove the
left axle hub bolt.
4. Install left rear wheel axle hub bolt
(1) As shown in the illustration, install the gasket and nut on the
new left axle hub bolt.
(2) Using a screwdriver or similar, hold the left axle hub subassembly,
install the left axle hub bolt by tightening the nut.
5. Install rear brake drum subassembly
6. Install rear wheel
Torque: 103N.m The replacement of the right rear axle hub and bearing assembly is the same as that of the left one.Washer
Nut -

Section 3 Front Wheel AlignmentAdjustment:1. Check tire
2. Measure the vehicle height
Vehicle height:Tire sizeFront1 (mm)Rear2 (mm)
175 / 65R14 82H191 265
185 / 60R15 84H192 265Front Suspension System-Front Wheel Alignment4-43 1.front measure point
Measure the distance between the ground and the front underside
suspension mounting bolt center
2.rear measure point
Measure the distance between the ground and the rear axle beam mounting bolt center
Notice:
Before the wheel alignment,adjust the body to the specified height.If the body height is out of spec,adjustment
shall be done by pressing or raising vehicle body.
3. Check the Toe-in
Toe-in:
If the toe-in is out of spec, adjust the ends of rack.
4. Adjust the Toe-in
(1) Remove the clamp of the rack boot
(2) Loose the jam nut of tie rod
(3) Adjust the Toe-in by rotating the same turns of both ends of
rack.
Tips: Adjust the toe-in to the intermediate value of spec.
(4)Make sure the same length for both ends
The length difference of left and right: 1.5mm or smaller
(5)Tighten the jam nut of the tie rod
Torque: 47N.m
(6)Seat the boot and crimp the clamp
Tips: rack boot must not be twistedFront
Rear
Front

(9) Repeat the steps above, replace 1 or 2 bolts
Tips:
Only replace 1 bolt if 2 bolts are needed to be replaced.bolt
Adjustment
value
15'
30'
45'
1°00'Location bolt
AAdjusting bolt
BC
1 point
2 point12121211.
11.
11 .Front Suspension SystemFront Wheel Alignment4-45 Refer to the table below to fix the correct adjustment if the camber is out of spec, then select the bolts for camber
adjustment.
Notice: Tighten the adjustment nuts with washer and new nuts. (4) Mount 2 nuts temporarily.
(5) Adjust the camber angle by pushing or pulling the underside
of shock absorber in the direction of required adjustment.
(6) Tightening the nuts
Torque: 132N.m
(7) Mounting the front wheel
Torque: 103N.m
(8) Check the camber
Tips:

Adjust the camber to the median of spec.
Adjustment value of positioning the bolts: 6' ~ 30'.
(0.1° ~ 0.5°)Adjusting bolt-