2008 GEELY MK service

Chapter 8 Power Steering SystemSection 1 Power Steering System3. Precaution: (1) Precaution for steering system
Make sure of the correct replacement of parts, incorrect replacement might affect the performance of the
steering system and lead to driving accidents.
(2) Precaution for SRS System
This vehicle is equipped with SRS (Supplemental Restraint System), driver side air bag and front passenger
side air bag.
Failure to carry out service operations in the correct sequence could cause the unexpected deployment of
the air bag during servicing, possibly leading to a serious accident.1. Power Steering System Description Power Steering System consists of the steering wheel, steering transmit device, power steering fixed device
and steering pipelines. The steering gear is rack and pinion type.2. Major parameters for steering system:Power Steering System-Power Steering System4-67Item
Steering Wheel total revolutions
Maximum Front
Wheel Turn Angle
Minimum Turning DiameterParameter
3.58±0.1
37.2°±2°/ 32°±2°
37.2°±2°/ 32°±2°
10.4
mInner
OuterSuspected Area
1. Tire (improperly inflated)
2. Power steering fluid (insufficient)
3. Front wheel alignment (incorrect)
4. Steering knuckle (worn)
5. Swing arm ball stud pin joint (worn)
6. Steering column (bent or binding)
7. Power steering pump assembly
8. Power steering gear assembly
1. Tire (improperly inflated)
2. Front wheel alignment (incorrect)
3. Steering column (bent or binding)
4. Power steering gear assemblySymptom
Heavy steering
Poor return4. Symptom Table The table below is helpful to find the cause of the problem. The numbers indicate the priority of the likely cause
of the problem. Check each part in order. Repair or replace these parts or assemblies if necessary.

Analog instrument (Km/h)
Instrument indication Displayed value of detector
20 17-23
40 35-40
60 55-60
80 75-80
100 95-100
120 114-120
140 133-140
160 152-160
180 171-180
Tachometer (r/min) Hand revolution counter (r/min)
800 740-860
1000900-1100
20001850-2150
30002800-3200
40003800-4200
50004800-5200
60005750-6250 Note:
Insufficient or too high tire pressure will increase error.
2. Check input signal
(1) Connect positive pole (+) of voltmeter with terminal C 16, connect negative pole (-) with terminal C15.
(2) When vehicle runs at 10km/h, check the voltage between terminal C15 and C16 of combination instrument
assy.
Standard: 7 high low level fluctuation waveforms per second.
Note:
To check, keep ignition switch in ON position, connector in on state
3. Check tachometer
Check service condition
Start up engine, use hand revolution counter for comparison.
Displayed value of hand revolution counter and indicated value of tachometer are shown in the table on
next page.
Analog instrumentIII. Inspection on vehicle1. Use speedometer detector to check indication error permitted by speedometer, check odometer service
condition.5-18Combination Instrument System -Malfunction Symptom Table and Troubleshooting

Chapter 4 Light SystemSection 1 Light System IntroductionI. Composition Light system comprises external illumination and signal system and internal illumination system.
The function of the external illumination and signal system is to illuminate the road ahead and send signals
to other vehicles.
The internal illumination system provides internal illumination for driver and passengers.II. Precaution for service1. Precaution when repairing electrical equipments
Disconnect the battery ground cable.
2. Precaution when replacing a headlamp bulb
(1) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.
(2) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.
(3) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are
turned ON, its service life will be shortened.
(4) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.
They can explode if dropped to ground. The glass fragments will splash up.
(5) When replacing, make sure to use the bulbs with the same power, same model.
(6) After the bulb is installed, make the lamp holder tight.III. Bulb specificationsRemark: All bulbs are made by Philips Corp..Light System-
Light System Introduction5-26Name Specifications
Headlamp (High beam and Low beam) H1 12V 55W
Turn signal lamp PY21W 12V 21W
Position lamp W5W 12V 5W
Front fog lamp H3 12V 55W
Rear combination lamp (Turn signal lamp) PY21W 12V 21W
Rear combination lamp (Brake / Position lamp) P21/5W 12V 21/5W
Rear combination lamp (Rear fog lamp) P21W 12V 21W
Rear combination lamp (Back-up lamp) P21W 12V 21W
Interior lamp (dome lamp) R5W 12V 5W
Rear row reading lamp C5W 12V 5W
Side turn signal lamp W5W 12V 5W
High mounted stop lamp (incl. rear trunk lamp) W5W 12V 5W
License plate lamp W5W 12V 5W
Door courtesy lamp W5W 12V 5W

Section 4 Audio System ReplacementI. Notice on operation Please explain to the customer that the AM/FM broadcast channel information will be cleared when removing
the battery negative terminal cable. Record the channel information before removing the negative terminal cable
if necessary. Reset after connecting the negative terminal cable.
All cassette tapes and CDs must be taken out before radio removal and installation.
If the cassette tapes and CDs can not be taken out due to radio fault. Do not take them out by force. Drive the
vehicle to Service Station.
Make sure the grounding bolts are tightened before antenna removal and installation.
There will be noise when receiving electric wave if the grounding bolts are not tightened.
Don't touch the speaker cone.II. Radio assembly1. Remove middle instrument board (see internal decorations)
2. Remove radio with bracket assembly
a. Remove four screws
b. Disconnect connector
3. Remove left bracket
a. Remove four screws
4. Remove right bracket
a. Remove four screws
5. Remove radio assemblyAudio System -Audio System Replacement5-52III. Front loudspeaker assembly
1. Remove door handhold
2. Remove front door electric piovted window switch assembly
3. Remove front door decorative internal plate assembly
4. Remove front door 5 inch loudspeaker assembly
a. Disconnect connector
b. Avert 3 rivets using a bit less than 4 mm (place bit in center
of rivet to bore out flange, be careful that newly cut rivet is
hot), take down loudspeaker assembly.
IV. Tweeter assembly
1. Remove door handhold
2. Remove front door electric piovted window switch assembly
3. Remove front door decorative internal plate assembly
4. Remove front door tweeter assembly
a. Disconnect connector
b. Remove two tapping screws and speaker assembly

Chapter 6 SRS (Supplemental Restraint System)Section 1 SRS-General InformationI. Precaution for service For safe reasons, read the following precaution before starting any operation.
1. When servicing the SRS, correct sequence and items are described in the following chapter.
2. Instruments and special tools recommended in this chapter shall be used for operation.
3. When servicing the following components, replace them with the new ones if there is a failure.
(1) SRS ECU
(2) Clock Spring Module
(3) Driver Airbag Module
(4) Passenger Airbag Assembly
(5) Front Seat Belt Pretensioner
4. If there is any abnormality in the wire harness of the SRS, replace it with a new one. Correct or replace the
abnormal wire harness in accordance with Table 1.pin1 pin15
pin29
pin16SRS (Supplemental Restraint System)-SRS-General Information5-54No Designation
1 Belt-pretensioner, Driver, Low
2 Belt-pretensioner, Driver, High
3 Belt-pretensioner, Passenger, High
4 Belt-pretensioner, Passenger, Low
5 IGN
6 GND
7WL
9K
10 DAB Hi
11 DAB Lo
13 (Optional) PAB Hi
14 (Optional) PAB Lo
27 Crash Output ECU Terminal Description5. Servicing operation shall be carried out 60s after the negative(-) terminal cable is disconnected from the battery.
In addition, the disconnected negative (-) terminal cable shall be protected with insulating tape for insulation. In

Instrument Designation Usage
Diagnostic detector (Hi-DS T Scan meter)
Special diagnostic meterCheck system troubles of the SRS,
and clear the DTC of ECUIII. Troubleshooting1. Basic process of trouble diagnosis
DTC of the present fault may coexist with that of the history fault.
Notice:

After the new SRS ECU is installed, the warning light of the SRS, with the ignition switch ON, will be on
for 4s and then go out permanently, indicating SRS works normal. In this case, no service is needed. Otherwise,
system diagnosis and service shall be carried out.
If with the ignition switch ON, the warning light of the SRS is not on, the relevant circuits of the warning
light shall be serviced. Then go on with the operation and enable it to work.SRS (Supplemental Restraint System)-
SRS-General Information5-55order to deploy an airbag within a certain time period after the battery
is disconnected, condenser in the ECU shall retain some electrical
energy. Otherwise, it could lead to a serious accident because of the
unexpected deployment of airbag.
6. During spray paint work, ECU, airbag assembly, clock
springassembly, etc shall be removed and kept in place to avoid the
effects of overheat. (Over 93)
7. When the SRS is serviced, a diagnostic scan meter is used to clear
the DTC to enable the normal work ofthe warning light.II. Test instrumentWarning light con-
stantly goes onuse scanner find out the troubletroubleshootingtrouble eliminated Check SRS warning light (see the right figure)
(1) Turn the ignition switch ON and find out whether the warning
light is on.
(2) 4 seconds after the process of ON-OFF, confirm that the
warning light goes out permanently.
(3) Otherwise, diagnosis and checking have to be involved in.
2. System Diagnosis
The SRS ECU will perform a series of circular diagnostic tests to check the readiness of the SRS functions.
This test can avoid unexpected explosion of the restrain system and in the same time ensure the necessary explosion
in a crash. If a trouble is detected, the SRS ECU will store a proper DTC and turn on the warning light indicating
a trouble for service.SRS Air Bag
Warning LightBattery
Cable Insulation BandSRS Air Bag
Warning Light

5-62 (22) There are problems in the configuration of the airbag ECU (DTC 93D6)
When using the scan tool to test the airbag ECU, the DTC is 93D6, indicating that there are problems in the
configuration of the airbag ECU.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93D6? Go to step 2 other
2Go to step 3
3 Go to step 4 Go to step 1
4 The fault has been removed, use the scan tool to eliminate the DTC.Check whether the configuration of the airbag ECU is consistent with the
actual on-board configuration?
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check). (23) The impact signal output interface of the airbag ECU is short to ground or the impact output circuit is
disconnected. (DTC 93D7)
When using the scan tool to test the airbag ECU, the DTC is 93D7, indicating that the impact signal output
interface of the airbag ECU is short to ground or the impact output circuit is disconnected.IV. Diagnosis of collided vehicle No matter airbag is unfolded or folded, inspection and maintenance of collided vehicle should be performed
according to the following sequence.
1. Check ECU diagnosis signal.
(1) Connect scanner diagnosis joint
(2) Use scanner to read out diagnosis result.
2. Repair sequence
(1) when airbag is unfolded.
The following components should be replaced with new parts
a. Airbag assembly on passenger side
b. ECU
c. Airbag assembly on driver side
d. Seat belt with pretensionerNote:
due to impact, when battery power is insufficient, scanner can not communicate with ECU, now check and
service instrument board wire harness or use external power supply.SRS (Supplemental Restraint System)-SRS-General Information (2 ) Check the following components, if there is any abnormity, replace with new parts
a. Clock spring.
b. Steering wheel, steering column, lower steering shaft assembly
(3 ) The installation status of driver airbag assembly in relation to steering wheel
a. Check and see if there is abnormal noise in the steering wheel, the action of the same is good, or the
clearance is normal.
b. Check the connecter of the wire harness for damage and the terminal for distortion.

5-69Notice
Work must be started 60s after the positive (+) and negative (-) terminal cables are detached from battery.
3) The airbag assembly shall be deployed according to the following procedures.
(1) Driver airbag assembly
a. Remove the knee bolster.
b. Remove the connector (yellow) that connecting the lower end of the clock spring with the wire harness
of the instrument panel (see the figure below).Notice
Remove the connector of the clock spring from the wire harness of the instrument, the connector will be
short circuited automatically, which can avoid the possible serious accident resulted from the deployment of
the diver airbag assembly due to static electricity.
c. Tie two 6m plus wire harnesses for deployment to the
adaptor wire harness of the airbag, and wrap the connecting points
with insulating tape for insulation.The other ends of the wire harness
for deployment are connected to each other (short circuited). Unex-
pected deployment resulted from static electricity shall be prevented.
d. From the yellow connector of the clock spring, lead the
airbag adapter wire harnesses out of the vehicle by means of the wire
harnesses for deployment (see the figure below).
e. To restrain the noise, close all the windows and doors and
put on the vehicle cover.Notice
The glass will likely break up if there is crack. Vehicle covers shall be put on.
f. Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect them with the two terminals of the battery removed from the
vehicle and deploy the airbag (see the figure below).Notice
Make sure there is no man inside or near the vehicle and then
carry out the operations.
After the driver airbag is deployed, the gas generator is of high
temperature. Keep it for 30 minutes until it gets cool for use.
If the driver airbag assembly cannot be deployed, discuss the
problem with the local Geely service station.Deployed
HarnessCovering the car g. The deployed driver airbag assembly shall be scrapped according to the scrapping procedures.
Deploy outside the vehicleNotice
Keep the airbag over 6m away from a obstacle or person and deploy the airbag in an open flat area.
Deployed the airbag outside the vehicle, avoid to do this job in the strong wind. In case of breeze, fire should
be against the wind.SRS (Supplemental Restraint System)-
SRS-General InformationDAB
Connector Horn
Connector