2008 GEELY MK wheel

5-62 (22) There are problems in the configuration of the airbag ECU (DTC 93D6)
When using the scan tool to test the airbag ECU, the DTC is 93D6, indicating that there are problems in the
configuration of the airbag ECU.
Step Operation Yes No
1 When using the scan tool to test the airbag ECU, is the DTC 93D6? Go to step 2 other
2Go to step 3
3 Go to step 4 Go to step 1
4 The fault has been removed, use the scan tool to eliminate the DTC.Check whether the configuration of the airbag ECU is consistent with the
actual on-board configuration?
After the troubleshooting, switch on the power supply, observe the status
of the warning light. The warning light shall goes off after lighting up for
4 seconds (self-check). (23) The impact signal output interface of the airbag ECU is short to ground or the impact output circuit is
disconnected. (DTC 93D7)
When using the scan tool to test the airbag ECU, the DTC is 93D7, indicating that the impact signal output
interface of the airbag ECU is short to ground or the impact output circuit is disconnected.IV. Diagnosis of collided vehicle No matter airbag is unfolded or folded, inspection and maintenance of collided vehicle should be performed
according to the following sequence.
1. Check ECU diagnosis signal.
(1) Connect scanner diagnosis joint
(2) Use scanner to read out diagnosis result.
2. Repair sequence
(1) when airbag is unfolded.
The following components should be replaced with new parts
a. Airbag assembly on passenger side
b. ECU
c. Airbag assembly on driver side
d. Seat belt with pretensionerNote:
due to impact, when battery power is insufficient, scanner can not communicate with ECU, now check and
service instrument board wire harness or use external power supply.SRS (Supplemental Restraint System)-SRS-General Information (2 ) Check the following components, if there is any abnormity, replace with new parts
a. Clock spring.
b. Steering wheel, steering column, lower steering shaft assembly
(3 ) The installation status of driver airbag assembly in relation to steering wheel
a. Check and see if there is abnormal noise in the steering wheel, the action of the same is good, or the
clearance is normal.
b. Check the connecter of the wire harness for damage and the terminal for distortion.

6. Steering wheel, steering column and steering lower shaft component.
(1) Check the installation status of driver airbag assembly.
(2) Check the steering wheel for any abnormal noise and see if the clearance is normal.
7. Check the wire harness connector (instrument panel wire harness).
Check and see if the wire harness is securely installed, if the joint is damaged and if the terminal is distorted.V. Warning marks When using or maintaining an airbag, the warnings shall be indicated. When maintaining, proceed in
accordance with the description of mark. In addition, if the mark is damaged or stained, it shall be replaced.
(1) Steering wheel, see Fig. 1.
(2) Driver airbag assembly, see Fig. 2.
(3) Clock spring, see Fig. 3.
Fig. 1.Fig. 2.Warning markFig. 3.Warning
mark (4) ECU, see Fig. 4.
(5) Sunshade, see Fig. 5.VI. SRS electronic control unit (ECU)Removal and Installation
1. Operations prior to Removal
(1) Turn the ignition switch OFF.
(2) Remove negative (-) terminal cable of the battery. Put it in a proper position or wrap it up with insulating
tape.Fig. 4.Fig. 5.5-64SunshadeSRS (Supplemental Restraint System)-SRS-General Information

Notice
1. Work must be started 60s after the negative (-) terminal cable is detached from battery. The detached
negative (-) terminal cable shall be protected with insulating tape for insulation.
2. Never attempt to dismantle or repair an ECU. If there is any trouble, replace the ECU with a new one.
3. Prevent the ECU from shock or vibration. If pitting, crack or distortion is found, replace the ECU with a
new one.
4. Every time an airbag is deployed, the ECU shall be replaced with a new one.
5. When disassembling or maintaining the parts around ECU, attention must be given to avoid contacting the
ECU. 2. Removal procedures:
(1) Remove the miscellaneous box in the middle consoce.
(2) Remove the connectors to SRS ECU.
(3) Remove ECU.
3. Installation procedures:
(1) Install ECU.
(2) Install the connectors to SRS ECU.
(3) Install the miscellaneous box in the middle consoce.
(4) Connect negative (-) terminal cable of the battery.
4. Key points for Installation:
(1) Install ECU.Notice
If the ECU cannot be installed correctly, the airbag will not act normally.
5. Check
a. ECU case for pitting, crack and distortion
b. The connector for damage and distortion.Notice
If pitting, crack or distortion is found on an ECU, replace it with a new one.VII. Airbag assembly & clock spring1.Removal and Installation of driver airbag and clock spring
Operations prior to removal
(1)Take out the ignition key after the steering wheel and front
wheel are adjusted to straightforward direction.
(2)Remove negative (-) terminal cable from the battery.
Removal procedures of the driver airbag assembly:
(1) Unscrew the screws of the two sides, see fig.15-65SRS (Supplemental Restraint System)-SRS-General Information (2) Check after installation.
a. Turn the ignition switch ON.
b. The warning light goes on within 4s, and then goes out.
(3) If the light doesn't go out, check the trouble and eliminate it.
For other ECU inspections, see Troubleshooting.
fig.1

(2) Disconnect the connector of the wire harness.
(3) Remove the components of airbag assembly.
(4) Remove steering wheel.
Removal procedures of clock spring:
(1) Remove the driver airbag assembly (disconnect the connector).
(2) Remove steering wheel gently (see the precaution).
(3) Remove the steering column cover and disconnect the connector of wire harness in the lower end.
(4) Remove clock spring.
Installation procedures of the driver airbag assembly
(1) Pre-Check

1- Install steering wheel

2- Connect the wire harness

3- Install driver airbag assembly

4- Screw up the installation screws of the two sides
(2) Connection of the negative (-) terminal of the battery
(3) Check after installation.
Installation procedures of clock spring:
(1) Pre-Check

1- Connection and fixation of the clock spring and combination switch

2- the connector of wire harness in the lower end
3- the steering column cover
4-Thread the line at the upper end of the clock spring through hole on the body part of the steering wheel
5-Install the steering wheel
6-Connect wiring harness
7-Install the airbag assembly components
(2) Connect the negative (-) terminal cable of the battery
(3) Check after installation5-66Key points for installation
(1)Pre-Check
a. The new airbag or clock spring shall be checked before being installed.SRS (Supplemental Restraint System)-SRS-General InformationNotice
Use scanner to do adiagnossis of airbag circnit, not to break down.
Keep the removed driver airbag assembly upside down in a clean and dry place.Notice
Keep the removed clock sprint in a clean and dry place.fig.2Installation nutRemoval of steering wheel (see the figure 2)
(1) Remove the installation screws from the middle and remove
the steering wheel.(Disconnect the horn connector)

5-67Notice
When connecting or disconnecting the turn the ignition switch OFF first.
d. Turn the ignition switch ON.
e. Read the diagnostic circuit and see if the other locations than the troubled area of the airbag are normal.
f. Turn the ignition switch OFF.
g. Remove the negative (-) terminal cable from the battery, and protect it with insulating tape for insulation.Notice
Work must be started 60s after the negative (-) terminal cable is disconnected from battery.
(2) Installation of clock spring
Screw up the clock spring clockwise to the end, rotate it counter-
clockwise by 2.5 turns, and align it with the mark (see the figure 3).Notice
If the center of the clock spring cannot be aligned, the steering
wheel will not turn midway, or cause bad performance to the clock
spring circuit, consequently hamper the normal action of the airbag.
(3) Installation of the components of the steering wheel and airbag assembly
a. When the center of the clock spring is aligned, install the components of the steering wheel and airbag
assembly.
b. After being installed, rotate the left and right sides of the steering wheel to position, and make sure there
is no abnormality.
(4) Check after installation
a. Slightly rotate the steering wheel left and right, make sure that there is no abnormality or noise. (Driver
airbag module, clock spring)
b. Turn the ignition switch ON.
c. The warning light goes on within 4s, and then goes out.figure 3SRS (Supplemental Restraint System)-
SRS-General Information b. Connect negative (-) terminal cable of the battery.
c. Connect the diagnostic connector (16 pins).Notice
In case of scrapping an airbag, it shall be noted that the airbag shall be deployed according to the specified
procedures before being scrapped.SRS Air Bag
Warning LightNotice
When installing the components of the steering wheel and
airbag assembly, attention should be given to protect the wire
harness of the clock spring from seizure.
d. The trouble shall be eliminated if the warning light remains on when the ignition switch is turned on or
after it goes out after 4s.

1) Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery from
the vehicle.Notice
Work must be started 60s after removal of the battery.Notice
When the connector is not connected, the terminals of the driver airbag assembly will be short circuited
automatically, preventing the airbag from being deployed unexpectedly. If the airbag is deployed unexpectedly,
the deployed surface should face up. It should be kept on a flat surface without any other items on it. 2) The airbag assembly shall be deployed according to the following procedures.
Driver airbag assembly
a. Remove the driver airbag assembly from the vehicle.
b. Prepare two 6m plus wire harnesses for deployment, connect
the other two ends to avoid unexpected deployment in case
of static electricity (see the figure below).Notice
The above-mentioned procedures can prevent the unexpected deployment due to static electricity and shall
therefore be performed strictly.Deployed Harness
Short Circuit Point
More than 6mInsulation tapeDeployment
wire harness
Short circuit
locationDriverÕs airbag
moduleAirbag assembly
Deployed
harness c. Touch the body of the vehicle with hands for static electricity elimination.
d. Cut off the wire harnesses of the driver airbag assembly and
connect them with the two wire harnesses for deployment,
and make sure to wrap up the connecting location with
insulating tape for insulation (see the figure on the right).
f. Pass the deployment wire harness of the driver airbag
assembly through an old tire with rim, and fix upwards the
driver airbag assembly by means of the wire connected to
the bolts, etc (see the figure on the right). e. Install the unused bolts to the inside bolt of the driver airbag assembly,and tie a thick metal wire securing
the wheel rim.5-70SRS (Supplemental Restraint System)-
SRS-General Information

Step Action of operator Screen displayResult in normal conditionPump motor works
Wheel lockup
Wheel lockup
Wheels may rotate freely,
pedal rebounds, work noise
of pump motor may be heard
Wheels may rotate freely
Wheel lockup, pedal auto-
matically goes down slightlyHydraulic control unit diagnosis -- hydraulic pump testLeft front wheel -- step down brake pedal
Left front wheel -- normally open valve opens,
normally closed valve is closed, wheel lockup?
Left front wheel -- normally open valve is closed,
normally closed valve is closed, wheel lockup?
Left front wheel _ _ normally open valve is closed,
normally closed valve opens, wheels may rotate
freelyLeft front wheel _ _ normally open valve is closed,
normally closed valve is closed, wheels may rotate freelyLeft front wheel -- normally open valve opens,
normally closed valve is closed, wheel lockup?
Release brake pedal 01
02
03
04
05
06
07
08Step down brake
pedal and hold
* Perform testing of the above steps 2-8 for each wheel. Sequence is as follows: left front right front left
rear right back.
* If result of one of the above steps is different from the result in normal condition, it shows that corresponding
actuator fails to work normally, please check corresponding actuator.
* Here as long as "return " position appears on the screen, it may finish the testing via "ESC " key and returns
to function menu.VI. Troubleshooting quick index tableMK-60 ABS system - ABS Diagnosis5-100Diagnostic
codeFault description Diagnosis contentCheck
list No.Reference
page
65535
01276
00283
00285
00290
00287
01044
00668
01130Electronic control unit
ABS hydraulic pump
Left front wheel sensor
Right front wheel sensor
Left rear wheel sensor
Right rear wheel sensor
ABS coding error
Supply terminal 30
ABS works abnormallyDamaged
Motor cannot work
Electric and mechanical failure
Signal lacks of conformity5-103
5-104
5-106
5-106
5-107
5-107
5-108 1
2, 3, 4
5
6
7

Whether sensor is installed
correctlyYes
Install it correctlyCheck sensor output volt-
age at ABS ECU 25 chip
socketAbnormal
ReplaceCheck each wheel
speed sensorAbnormalReplace ABS ECUNormal
Replace or
repairCheck wheel bearing
clearanceAbnormalCheck wiring harnessbetween sensor andABS ECUNormalMK-60 ABS system -ABS System Check5-104Fault code is 00283, 00285, 00290, 00287 2
[Description ] when open circuit cannot be detected, there is no signal output
even if vehicle speed reaches above 20 km/h, this fault code
will appear.
[Prompt ] It is probably because that sensor is not mounted, sensor coil or
wiring harness is shorted, air gap between sensor and gear ring is
too large or gear ring is damaged.Possible cause

Sensor is not mounted

Sensor coil or wiring har-
ness is shorted

Air gap between sensor
and gear ring is too large

Gear ring is not mounted

ABS ECU fails
ReplaceCheck the pulse ringAbnormalNormal