2008 GEELY MK bulb

Transmission ControlAutomatic Transmission Shift Mechanism4-8Component ViewAutomatic Shifter Panel
Dust-Proof Sliding Plate
Gear Range Display
Shift Lock Release Button
Cap
Bulb
Button Spring
Gear Range Indicator
Wire Harness
Shift Lock Unit
Solenoid
Shift Lock Control ArmShift Lever Sub-AssemblyControl Shaft Key Retaining
Cable Control
Arm Slot Pin Shift Lever SupportHandle Connecting RodShift Lever Button Shift Lever Knob Cover
Spring Automatic Shift Handle
Spring Inner Rod
Precoated Part -

Chapter 4 Light SystemSection 1 Light System IntroductionI. Composition Light system comprises external illumination and signal system and internal illumination system.
The function of the external illumination and signal system is to illuminate the road ahead and send signals
to other vehicles.
The internal illumination system provides internal illumination for driver and passengers.II. Precaution for service1. Precaution when repairing electrical equipments
Disconnect the battery ground cable.
2. Precaution when replacing a headlamp bulb
(1) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.
(2) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.
(3) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are
turned ON, its service life will be shortened.
(4) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.
They can explode if dropped to ground. The glass fragments will splash up.
(5) When replacing, make sure to use the bulbs with the same power, same model.
(6) After the bulb is installed, make the lamp holder tight.III. Bulb specificationsRemark: All bulbs are made by Philips Corp..Light System-
Light System Introduction5-26Name Specifications
Headlamp (High beam and Low beam) H1 12V 55W
Turn signal lamp PY21W 12V 21W
Position lamp W5W 12V 5W
Front fog lamp H3 12V 55W
Rear combination lamp (Turn signal lamp) PY21W 12V 21W
Rear combination lamp (Brake / Position lamp) P21/5W 12V 21/5W
Rear combination lamp (Rear fog lamp) P21W 12V 21W
Rear combination lamp (Back-up lamp) P21W 12V 21W
Interior lamp (dome lamp) R5W 12V 5W
Rear row reading lamp C5W 12V 5W
Side turn signal lamp W5W 12V 5W
High mounted stop lamp (incl. rear trunk lamp) W5W 12V 5W
License plate lamp W5W 12V 5W
Door courtesy lamp W5W 12V 5W

Symptom
Front fog lamp dose not light up with light control
switch HEADLAMP (Head lamp is normal).
Only one side front fog lamp dose not lightSuspected Area
1. Fog lamp fuse
2. Front fog lamp relay
3. Light switch assembly
4. Harness
1. Bulb
2. HarnessSection 2 Light System Malfunction InspectionSuspected Area
1. Bulb
2. LH or RH headlamp fuse
3. Harness
1. Lamp switch assembly
2. Harness
1. Bulb
2. LH or RH headlamp fuse
3. Harness
1. Lamp switch assembly
2. Harness
1. Lamp switch assembly
2. Harness
1. Bulb
2. Harness
1. Bulb
2. Harness
1. Fuse
2. Light control switch
3. Harness
1. Beam control switch
2. Harness2. Front fog lamp systemSymptom
"Low beam" dose not light (One side)
"Low beam" dose not light (All)
"High beam" dose not light (One side)
"High beam" dose not light (All)
Light dose not flash (Dimmer)
Headlamp is dim
Only one side tail lamp lights
Tail lamps on both sides do not light (Headlamp
is normal)
Tail lamps on both sides do not light (Headlamp
is abnormal)Light System -Light System Malfunction Inspection5-28I. Light system problem symptoms table: Description:
The table below can help you find the causes of malfunction. These figures show the most possible
malfunctions in order of priority. Inspect each part in the order given. If necessary, repair or replace these parts.
1. Headlamp and tail lamp

Symptom
Rear fog lamp dose not light up with light control
switch on FRONT FOG LAMP (Small lamp is
normal).
Rear fog lamp dose not light up with light control
switch on FRONT FOG LAMP (Small lamp is
abnormal).
Only one side rear fog lamp dose not lightSuspected Area
1. Bulb
2. Light switch assembly
3. Harness
1. Bulb
2. Tail lamp fuse
3. Harness
1. Bulb
2. Harness 3. Rear fog lamp system
Symptom
"Hazard" and "Turn" does not work
Hazard warning lamp does not work (Turn is
normal)
Hazard warning lamp is abnormal (Hazard is
abnormal)
Turn signal dose not light up in one direction
Only one bulb dose not light upSuspected Area
1. HAZARD Fuse
2. Central controller
3. Harness
1. Hazard warning switch
2. Harness
1. Turn signal switch
2. Harness
1. Turn signal switch
2. Harness
1. Bulb
2. Harness
Symptom
Brake lamps on both sides do not light up
Brake lamp remains always ON
Brake lamp dose not light (One side)
High mounted Brake lamp dose not light up
(Stop lamp is normal)4. Turn signal and hazard warning system
5. Brake lamp system
Suspected Area
1. Brake lamp fuse
2. Brake lamp switch
3. Harness
1. Brake lamp switch
2. Harness
1. Bulb
2. Harness
1. Bulb
2. HarnessLight System -Light System Malfunction Inspection5-29

Fault symptom
License light does not illuminate (taillight is
normal)Possible parts
1. Bulb
2. Wire harnessFault symptom
Trunk lamp does not illuminate (room lamp is
normal)Possible parts
1. Bulb
2. Trunk lamp switch
3. Wire harness Symptom
Back-up lamps on both sides do not light up
Back-up lamps on both sides remains always ON
Back-up lamp dose not light (One side)Suspected Area
1. Back-up lamp fuse
2. Back-up lamp switch assembly
3. Harness
1. Back-up lamp switch assembly
2. Harness
1. Bulb
2. Harness
Symptom
Interior lamp dose not light (All)
Room lamp dose not light up Rear row reading
lamp assembly is normal
One door is ajar, room lamp dose not light up on
DOOR, (It is normal on ON)
Central LH/RH room lamps do not light up
Rear row reading lamp is abnormal (Room lamp
assembly is normal)Suspected Area
1. ROOM Fuse
2. Harness
1. Bulb
2. Room lamp assembly
3. Harness
1. Door courtesy lamp switch
2. Central controller
3. Harness
1. Bulb
2. Switch
1. Bulb
2. Rear row reading lamp assembly
3. Harness 6. Back-up lamp system
7. Interior light system8. License light
9. Trunk lampLight System -Light System Malfunction Inspection5-30

Section 4 Front Fog Lamp ReplacementI. Removal1. Remove front bumper. (see bumper replacement)
2. Remove electrical connector.
3. Remove fixed bolt (as shown in the figure).
4. Remove front foglight assembly.II. Installation1. Install front foglight assembly.
2. Mount fixed bolt.
3. Mount electrical connector.
4. Mount front bumper.
5. Adjust vehicle state.
6. Adjust front foglight beam.III. Replacement of front head light bulb Remove dust shield by rotating anticlockwise
Pull out bulb plug
Press and loosen steel wire clip
Pull out lamp holder, take off bulb
Replace bulbLight System -Front Fog Lamp Replacement5-351-Turn light dust shield
2-Low beam dust shield
3-High beam, front position lamp dust shieldIII. Replacement of front foglight bulb1. Press and rotate anticlockwise, take off dust hood
2. Take out bulb
3. Replace bulbIV. Adjustment of front foglight beam1. Adjust tire pressure in standard value
2. Start up engine
3. Turn on foglight switch
4. Adjust foglight beam turn screw to adjust foglight beam in the vertical direction.
Description:
Turn screwdriver anticlockwise to make beam upward, or turn screwdriver clockwise to make it downward.

Section 6 High-mounted Stop light ReplacementDisconnect the connector.
Remove the High mounted stop lamp in direction 1 and 2. (as shown
above in the illustration)I. Removal1. Remove trunk weather strip and trim.
2. Remove 3 installation nuts (as shown in the figure).
3. Remove rear combination light electrical connector.
4. Pull out rear combination light assembly towards vehicle backside.II. Installation1. Mount rear combination light, mount 3 installation nuts.
2. Mount electrical connector.
3. Mount trunk trim.
4. Mount weatherstrip.III. Replacement of rear combination light bulb1. Take off seal ring
2. Turn lamp holder anticlockwise, take off lamp holder
3. Take off bulb, replace bulbSection 5 Rear Combination Lamp ReplacementRear
shelf
High-mount stoplightlamp
holderLight System -Rear Combination Lamp Replacement/High-mounted Stop light Replacement5-36

Lamp bodyaLamp
shade1. Use a screwdriver to slightly pry off lamp shade
2. Use a screwdriver to remove two screws (be careful
not to contact bulb)
3. Disconnect the connectorSection 7 Front Reading Lamp ReplacementSection 9 License Plate Lamp Replacement1. Use a screwdriver to slightly pry off rear reading light
2. Use a screwdriver to remove two screws (be careful not to
contact bulb)
3. Remove the connectorSection 8 Rear Reading Lamp Replacement1. Remove license light with a screwdriver from A & B point as
shown in the figure
2. Change bulbA BLight System -Front Reading Lamp Replacement/Rear Reading Lamp Replacement/License Plate Lamp Replacement5-37at position a (gap)