2008 GEELY FC ABS

Brake--Speed sensor of rear wheels153(c) Use special tool and press to assemble speed sensor of
rear wheels to rear shaft hub.
Note:zDo not use hammer knock directly in speed sensor
of rear wheels.zInsure no sundries are attached on the supervising
part of speed sensor of rear wheelszPress speed sensor of rear wheels straightly and
slowly.8. Assemble left rear shaft hub and bearing assembly
(referring to page 129).
9. Assemble brake disk.
10. Assemble left rear brake branch pump.
11. Assemble wiring harness of speed sensor of rear
wheels.
12. Assemble rear wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m13. Check and adjust wheel alignment.
14. Check the signal of ABS speed sensor.Special
tool

Circuitry--Power supply
1. ST startup system
2. HEAD MAIN light system
3. spare
4. ECU instrument travel
computer (Aldine)
5. horn
6. turn light, alarm light
7. charging system
8. air condition system
9. electric injection system
10. audio system, air condition,
instrument, room light, trunk
light, door light
11. AM2 startup system
12. spare safety
13. spare safety
14. spare safety
15. spare safety
16. electric chair (Aldine)
17. electric fan
18. ABS system
19. ABS system20. left distance headlight
21. right distantce headlight
22. left low beams
23. right low beams
 314 

Circuitry--Power supply
24. spare
25. OBD discharge test system
26. rear fog light
27. Anti-burglary
28. DOOR center control, light con-
trol system
29. Defrost load
30. spare
31. spare
32. eletric injection system, safety
airbag system, anti-burglary
system, instrument system
33. spare
34. spare
35. spare
36. front fog light
37. AMI ignition system
38. TAILposition light, number platelight
39. brake light
40. electric sunroof
41. instrument system, air condition
system, defrost system, Re-
verse Radar, rear light, turn light.
42. CIG air condition system, audio
system, electric rear view mirror,
cigarette lighter
43. washer
44. spare
45. wiper
46. spare
47. center control, light control
system, anti-burglary system,
ABS system
48. air condition system
49. rear defrost system
50. electric glass operator
 315 

Panel/combination instrument--combination instrument
Panel / combination instrument
combination instrument
Trouble table
Lightening:
Phenomenon
All lights fail
Only one light failsPossible parts of trouble
1. combination instrument assembly
2. joint or harness
1. combination instrument assemblyReference pages
-
-
-
Indicator light:
Phenomenon
Trouble light fails
Charge light fails
Brake system light fails
ABS light fails
SRS lights fails
Door light fails
low fuel level light fails
low Oil pressure light failsPossible parts of trouble
1. harness or joint
2. engine ECU
3. combination instrument assembly
1. harness or joint
2. engine ECU
3. combination instrument assembly
1. harness or joint
2. ABS ECU
3. combination instrument assembly
1. harness or joint
2. ABS ECU
3. combination instrument assembly
1. harness or joint
2. airbag sensor assembly
3. combination instrument assembly
1. harness or joint
2. door control switch
3. combination instrument assembly
1. harness or joint
2. fuel level light switch
3. combination instrument assembly
1. combination instrument assembly
2. oil pressure light switch
3. harness or jointReference pages
-
-
-
-
-
-
-
-
335
-
-
335
-
-
-
-
-
-
-
335
335
-
335
335
 334 

Panel/combination instrument-combination instrument
13. Check the switch of indicating light of brake liquid level.
(1) Disassemble the cover and filter screen of liquid storage tank of brake main pump.
(2) Disassemble the joint.
(3) Check the conduction between switch side joints.
Float (switch is OFF): not conduction
(4) Use siphon and other tools to absorb brake liquid in storage tank.
(5) Check the conduction between switch side joint terminals.
Sink (switch is ON): conduction
(6) Pour brake liquid into storage tank.
Inspection
1. Check the switch of indicating light of brake liquid level.
Check the conduction between switch side joint terminals.
Float ((switch is OFF): not conduction
Sink (switch is ON): conduction
2. Check parking brake switch.
Check the conduction between switch side joint terminals.
When switch pin is released: conduction
When switch pin is pressed: not conduction
 339 

Anti-locking brake system ABS Brake distribution EBDElectrical schematic diagram--Anti-locking brake system ABS Brake distribution EBD 397