2008 GEELY FC parking brake

15. Assemble parking brake exterior shoe assembly
(LH).
Use special tool to assemble parking brake shoe with parking
shoe, localizing spring and pin.
16. Assemble parking brake shoe adjustor.
(a) Spread high temperature lubricating grease on adjusting
bolt.
(b) Assemble parking brake shoe adjustor.
(c) Use needle-nosed pliers to assemble return spring.
17. Assemble support lever of parking brake shoe (LH).
(a) Spread high temperature lubricating grease on contacting
surface between shoe support lever and tension spring.
(b) Assemble support lever of parking brake shoe.
(c) Use needle-nosed pliers to assemble upper two tension
springs.
Parking brake--Parking brake assembly
Special
tool
 163 

18. Check the assembly of parking brake system.
Check every part after assembly.
Note: do not attach oil dirt or lubricating grease on contacting surface between shoe friction
sheet and brake drum.
Parking brake--Parking brake assembly
19. Assemble the brake
20. Adjust the clearance of parking brake shoe.
(a) Lock screw cap of shaft hub temporarily.
(b) Disassemble hole plug, then use screw driver to turn the
adjustor until brake drum is locked by shoe.
(c) Return the adjustor for 8 gears.
(d) Check whether shoe has lag.
(e) Assemble hole plug.
21. Assemble rear disk type brake branch pump assem-
bly (LH).
22. Assemble rear wheels.
Torque: 103
± ±± ±
± 10N
⋅ ⋅⋅ ⋅
⋅m
23. Check the travel of parking brake drag lever.
24. Adjust the travel of parking brake drag lever.
Left
Right
Front
Front
Increase the
clearance
Decrease the
clearance
 164 

15. Disassemble central ventilation orifice assembly of panel [68010012].
16. Disassemble right storage box assembly of lower panel [68010008].
17. Disassemble inner trim board assembly of right front column [68010017].
18. Disassemble inner trim board assembly of left front column [68010014].
19. Disconnect the joint of safety airbag assembly at the side of passenger.
20. Disassemble upper panel assembly [6801004].
21. Disassemble upper/lower trim board of steering pipe [64000128/64000129].
22. Disassemble left combination switch assembly [67000078].
23. Disassemble right combination switch assembly [67000079].
24. Disassemble air spring assembly of right storage box [68000082].
25. Disassemble decoration panel assembly of shift organization [68000076].
26. Disassemble air conditioner control panel assembly [67000148].
27. Disassemble the assemble bracket of CD machine.
28. Disassemble ventilation pipe assembly of evaporator [67000149].
29. Disassemble air conditioner control assembly.
30. Disassemble parking brake lever hole cover.
31. Disassemble auxiliary panel assembly.
32. Disassemble step trim board of right front door [68010021].
33. Disassemble step trim board of left front door [68010020].
34. Disassemble lower inner trim board of right defender [68010016].
35. Disassemble lower inner trim board of left defender [68010015].
36. Disassemble central linking board of lower panel [68010006].
37. Disassemble lower panel assembly [68010005].
38. Disconnect steering column assembly [64000122].
(a) Disassemble three bolts.
(b) Disassemble steering column from panel framework body.
Air conditioner--Air conditioner central heating core assembly
 228 

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338 

Panel/combination instrument-combination instrument
13. Check the switch of indicating light of brake liquid level.
(1) Disassemble the cover and filter screen of liquid storage tank of brake main pump.
(2) Disassemble the joint.
(3) Check the conduction between switch side joints.
Float (switch is OFF): not conduction
(4) Use siphon and other tools to absorb brake liquid in storage tank.
(5) Check the conduction between switch side joint terminals.
Sink (switch is ON): conduction
(6) Pour brake liquid into storage tank.
Inspection
1. Check the switch of indicating light of brake liquid level.
Check the conduction between switch side joint terminals.
Float ((switch is OFF): not conduction
Sink (switch is ON): conduction
2. Check parking brake switch.
Check the conduction between switch side joint terminals.
When switch pin is released: conduction
When switch pin is pressed: not conduction
 339 

Panel/combination instrument-- panel
L
4 Fixing
clasp
3 Fixing
clasp
Fixing
clamp
25. Disassemble parking brake hole cover.
Use screw driver to unclench four fixing clamps, then disas-
semble parking brake hole cover.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
26. Disassemble auxiliary panel assembly [68010002]
(a) Disassemble two L bolts, two C bolts and auxiliary panel
assembly.
27. Disassemble right front door pedal trim board
[68010021]
Use screw driver to unclench three fixing clamps, then disas-
semble right front door pedal trim board.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
28. Disassemble left front door pedal trim board
[68010020]
29. Disassemble lower inner trim board of right de-
fender [68010016]
(a) Disassemble plastic nuts of lower inner trim board of right
defender.
(b) Unclench fixing clamp, then disassemble lower inner trim
board of right defender liking that shown in figure.
30. Disassemble lower inner trim board of left defender
[68010015]
31. Disassemble connecting board at the middle of
panel [68010006]
(a) Use screw driver to unclench four fixing clamps, then open
the connecting board at the middle of panel.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble connecting board at the middle of panel.
 344