Page 247 of 419
Air conditioner--Condenser AssemblyCondenser AssemblyInspection on the automobile1. Check the Condenser Assembly.(a) If the radiating fins of condenser assembly are dirty, wipe it with water and blow it to dry with com-
pressed air.
Notice: Do not damage the radiating fin.
(b) If the radiating fin is curved, repair it with gad screw driver or pliers.2. Check whether the Condenser leaks.(a) Use leakage detector to check whether the Refrigerant leaks at the joint of the pipelines.
(b) If it leaks, check the fastening torque of joint part.Overhaul1. Disassemble the radiator cover assembly.
2. Recycle the HFC-134a(R134a)
3. Disassemble the Refrigerant liquid pipe A.(a) Disassemble the bolt from the condenser assembly and
disconnect the Refrigerant liquid pipe A.
(b) Disassemble the O-shape ring from the Refrigerant liquid
pipe.
Notice: The pipeline should be covered immediately
to prevent damp or dust from getting into the system.4. Disassemble the Refrigerant NO.1 high pressure
hose.(a) Disassemble the bolt and the Refrigerant NO.1 high pres-
sure hose from the condenser assembly.
(b) Disassemble the O-shape ring from the Refrigerant high
pressure hose.
Notice: The pipeline should be covered immediately
to prevent damp or dust from getting into the system.5. Disassemble the condenser assembly.(a) Disassemble those two bolts and the bracket on water tank. 236
Page 297 of 419
Light--Front fog light joint
Front combination light (LH)
Subassembly
Left front combination
light units
Front combination
light bulb
Front combination
light bulb
Front combination light
bulb joint Ultrasonic sensor joint Radiator cover
assembly
Front fog light
joint
Light
seat cap
Bulb joint
Bulb
Bulb
Front fog light joint
Front bumper
286
Page 298 of 419
Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure are the same on the left and right side.
zReferring to the drawing of front combination light on page 286.
1. Disassemble Radiator cover assembly (reference to page 380)
2. Disassemble left front tyre lining (reference to page 380)
3. Disassemble right front tyre lining (reference to page 380)
4. Disassemble front bumper (reference to page 380)
5. Disassemble left front combination light assembly [67000102]
(a) Disassemble three bolts
(b) Disassemble four joints
(c) Pull combination light ahead
(d) Disassemble two light seat cap and four bulbs.
Adjustments
1. Adjust front combination light focus only
(a) Parking car should accord to the following situations:
zFront combination light around does not be distorted or damaged.
zPark the car on flat road.
zTyre pressure limits to the regular number value
zThe driver is on driving seat and the car is ready to go(gasoline tank in full)
zThe car weaves fore-and-aft for many times.
(b) Inspect front combination light focus
(1) Prepare for thicker white paper
(2) Arise the paper plumb at the distance of 300cm from headlight.
(3) Make sure centerline of the car makes 90 degree angle with paper’s surface as following drawing.
(4) Draw a level line (H line) on the paper which headlight can irradiate.
(5) Draw a plumb line (V line) on the paper to across centerline of the car.
(6) Draw two level lines (V RH and V LH) in the area where two side lights can irradiate.
(7) Draw a level line(connect the middle signal of two low beam headlight) to the area where headlight
can irradiates.
Clues on: H RH and H LH lines are 0.57 lower than level line(H line)of light.
(8) Start the engine.
(9) Turn the front assembled switch to ON.
Pin
287
Page 390 of 419
Exterior/inner trim board--Front bumper
Exterior/inner trim board
Front bumper
Subassembly
Inner gasket of
right front wheel
Inner gasket of
left front wheel Fixing pedestal of
radar probe
Radar probe head
Radar probe head
Fixing pedestal of
radar probe head
Front fog light assemblyRadiator cover
assembly
Front bumper
Equipping with fog light
379
Page 391 of 419
Exterior/inner trim board--Front bumper
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of front bumper on page 379.
1. Disassemble radiator cover assembly [68000094]
(a) Disassemble the bolt and radiator cover assembly.
2. Disassemble inner gasket of left front wheel [68000225]
(a) Use disassembling tool for fixing clamp to disassemble two fixing clamps.
(b) Disassemble the screw and a part of inner gasket of left front wheel.
Hint: Disassemble the fixing clamp of screw and inner gasket of left front wheel in the scope of
front bumper which could be disassembled.
3. Disassemble inner gasket of right front wheel [68000228]
4. Disassemble front bumper [68000005]
(a) Disassemble four screws and two fixing clamps.
(b) Disassemble fixing clasp and front bumper.
(c) Equipping with fog light: disassemble two joints of fog light.
(d) Equipping with radar probe head: disassemble two radar probe heads (luxury type).
5. Disassemble reversing radar probe head assembly.
(a) Disassemble two fixing pedestals of radar probe head and two radar probe heads.
6. Disassemble left front fog light assembly [67000098]
(a) Disassemble fixing clasp and left front fog light assembly.
7. Disassemble right front fog light assembly [67000099]
380
