2008 GEELY FC airbag

Air conditioner--Air conditioner central heating core assembly
3. Disconnect refrigerant No.1 low pressure hose.
Note:
after disassembling the pipeline, it is necessary to cover
the joint to prevent humidity or dust from entering in
system.
4. Disconnect refrigerant liquid pipe A.
Hint:disconnect liquid pipe A with the method being
same as No.1.
5. Disconnect water outlet hose of heating.
(a) Slide out fixed clamp and disassemble water outlet hose
of heating.
6. Disconnect water intake hose of heating.
Slide out fixed clamp and disassemble water intake hose of
heating.
7. Disassemble cathode wire of battery.
8. Make front wheels face the front.
9. Disassemble safety airbag assembly at the side of
driver.
10. Disassemble steering wheel.
11. Disassemble combination instrument cover
[68000077].
12. Disassemble combination instrument assembly
[68000081].
13. Disassemble ventilation orifice assembly at the left
side of panel [68010010].
14. Disassemble ventilation orifice assembly at the right
side of panel [68010011].
Air conditioner central heating core assembly
Overhaul
1. Disassemble radiator cover.
2. Reclaim HFC-134a(R134a)
 227 
low pressure
hose
liquid pipe A

15. Disassemble central ventilation orifice assembly of panel [68010012].
16. Disassemble right storage box assembly of lower panel [68010008].
17. Disassemble inner trim board assembly of right front column [68010017].
18. Disassemble inner trim board assembly of left front column [68010014].
19. Disconnect the joint of safety airbag assembly at the side of passenger.
20. Disassemble upper panel assembly [6801004].
21. Disassemble upper/lower trim board of steering pipe [64000128/64000129].
22. Disassemble left combination switch assembly [67000078].
23. Disassemble right combination switch assembly [67000079].
24. Disassemble air spring assembly of right storage box [68000082].
25. Disassemble decoration panel assembly of shift organization [68000076].
26. Disassemble air conditioner control panel assembly [67000148].
27. Disassemble the assemble bracket of CD machine.
28. Disassemble ventilation pipe assembly of evaporator [67000149].
29. Disassemble air conditioner control assembly.
30. Disassemble parking brake lever hole cover.
31. Disassemble auxiliary panel assembly.
32. Disassemble step trim board of right front door [68010021].
33. Disassemble step trim board of left front door [68010020].
34. Disassemble lower inner trim board of right defender [68010016].
35. Disassemble lower inner trim board of left defender [68010015].
36. Disassemble central linking board of lower panel [68010006].
37. Disassemble lower panel assembly [68010005].
38. Disconnect steering column assembly [64000122].
(a) Disassemble three bolts.
(b) Disassemble steering column from panel framework body.
Air conditioner--Air conditioner central heating core assembly
 228 

Supplemental restraint system--Note
Note:
zWhen making repair, please make malfunction diagnosis by the flash light and malfunction diagnosing device
according with the method regulated in this operation manual at first, at the same time, it is necessary to check
whether there is any malfunction code before disassembling battery wire.
zForbid disassembling or repairing at any non-appointment repair station
zDo not assemble any safety lever or bumper at the front of automobile, this will influence the performance of this
airbag.
zPeople for repairing, disassembling and assembling should be trained specially.
zWhen disassembling steering wheel assembly, it is necessary to make steering wheel right, only this could disas-
semble steering wheel assembly and make helix cable locate correct position, or it will damage helix cable assembly.
zECU matches with the technical parameter of electric system, forbid using the SRS parts of other automobiles, at
the same time, it is necessary to use new product to replace any part.
zWhen repairing automobile (especially electric welding), it is necessary to close key switch, and it is best to cut off
the anode of battery.
zAfter unfolding airbag, safety airbag assembly and helix cable assembly should be changed completely.
zWhen disassembling or carrying airbag assembly, trim cover should face the upside; safety airbag assembly
could not superpose directly to avoid make wrong explosion and make any accident.
zThe inner malfunction of controller (ECU) could not repair, if it happens any malfunction, change it.
zSafety airbag assembly should be stored in the environment whose temperature is lower than 40C, relative humid-
ity is lower than 75% and is apart from electromagnetic interruption.
zForbid disassembling the airbag assembly and gas generator in it.
zForbid connect AC or DC with over 20V with ECU to avoid damage.
Supplemental restraint system
Note
Warning:
zThis product is the SRS (supplemental restraint system) equipped by JILI “YUANJIN vision” type automobile, when
the automobile frontal face is impacted heavily, this product could reduce the possible hurt for driver and passen-
ger at the front seat, but this product could not replace the safety belt. For SRS is supplemental restraint safety
system, the driver should tie safety belt. This product is single-point electronic dual-airbag system whose charac-
teristic is that all sensors and control circuits are assembled in control box and gas maker is protechny. At the
same time, this product accords with the enterprise standard “Automobile safety airbag equipment” (Q/JL001—
2001) to product.
zIn repairing process, if it does not accord with correct operation sequence to operate, SRS might happen the
accidental explosion to make heavy accident. If repair does not accord with correct procedure, even if repair does
not incur accident, SRS might disable when automobile happens accident, for example, it could not explode by
the requirement. So, when making repair (including disassembling, assembling, checking or changing any part),
it is necessary to operate by correct sequence regulated by repair manual.
zIt is necessary to confirm following works before repairing: 1. Put the ignition switch at “OFF” state. 2. Disconnect
the cathode connection of battery, and make repair after waiting for 60s. In addition, disassembled cathode
should be twisted by insulating tape to insulate. (Capacitor in ECU could keep some electric power after battery
is cut off to unfold safety airbag in some time. So, when making maintenance, if it does not wait for some time
before operating, it might incur heavy hurt accident for wrong expansion of safety airbag.)
zDo not put the parts of SRS directly under the insulation of hot air or flame.
 239 

Supplemental restraint system--Note
Special tools and measurers which any safety airbag repairing position should have:
Changeable subassembly which safety airbag repairing position should have:
a. Safety airbag assembly at the side of driver;
b. Safety airbag assembly at the side of passanger;
c. Helix cable assembly.
d. ECU assembly;
e. Steering wheel.
I. Safety airbag joint
No. ItemApplicable
(1) Terminal dual-locking organization
(2) Airbag anti-explosive organizationJoint 3, 4, 7, 8
(3) Checking organization of electric circuit connection
(4) Inadequacy connection protection organization Joint 4
(5) Joint dual-locking organization Joint 2
(6) Joint dual-locking organizationJoint 6, 7, 10
Safety airbag at the
side of passengerSafety airbag at
the side of driver
Helix
cable
Airbag controller
1. All safety airbag joints should be yellow to be easy to distinguish the joints on other automobile parts,
this could guarantee the safety performance and reliability of safety airbag joint, each kind of joint has
special function and design.
 240 
Number
a
b
c
d
eFunction
Disassemble airbag subassembly on steering wheel
Assemble and disassemble big nut on steering column
Assemble and disassemble ECU and safety airbag assembly
at the side of passenger on automobile body.
Used for electric measurement on wiring harness
Used for resistance measurement of electric ignition device
of airbag subassembly. Name and type of tool
5S hexagon wrench
Socket wrench 18S
14S socket wrench
Numeric multi-meter DT 992 type
Electric detonator tester
QJ992 type
Short
wiring
harness

(3) Joint dual-locking organization:
The joint equipping with this organization (male joint and female joint) is locked by dual-locking device
to increase the reliability of connection.
If one time lock is not firm, convex block will interrupt and stop the locking of twice lock. (1) Terminal dual-locking organization:
Each joint should be dual-locking organization and combines
with joint body and locking block. This design is caused by
the reason that dual-locking device (locking block and fixed
sheet) could fix the terminal to prevent it from releasing.
(2) Airbag anti-explosive organization
Each joint has a short circuit sheet, when the joint is
disassembled, short circuit sheet will connect the terminal
of device power supply with that terminal of igniter.
Mother
jointFather
joint Supplemental restraint system--Note
 241 
Body
Body
Body When connecting the joint
When disconnecting the joint
Short circuit spring sheet
Short circuit spring sheet
Terminal
Detonator
Short circuit spring sheetShort circuit spring sheet ON
Detonator
Closed circuitContact with father terminal
Joint
locklock Twice lock
Convex block
One time lock
One time lock is not firm
(twice lock is stopped)Twice lock is firm
(Twice lock could lock)Dual-lock could lock
completelyLocking block

(4) Joint locking organization:
Lock the locking clasp of joint to fasten the connection of joint.
2. When the automobile front face is impacted, and generated force is bigger than the standard pre-set,
airbag will work automatically. The sensor in safety airbag controller will feel the impact, at the same
time, it will judge the generation of impact by inner arithmetic to make ignition electric current. Electric
current will flow in gas generator to make explosive function, then two gas generators in airbag at the
side of driver and passenger will make gas to increase quickly inner pressure of airbag and rush out
the trim cover of steering wheel and instrument panel. After airbag charging is closed, the gas ejects
from the gas outlet at the side or at the back of airbag.
II. Disassemble the connecting joint of lower helix cable and wiring harness of steer-
ing wheel.
1. Put your finger on sliding block.
2. Move the sliding block to release the clasp.
3. Pull out the male joint.
Liking that shown in figure: some joints of wiring harness use the female joints in the right part of figure,
some designs of helix cable is similar with the joints in the left part.
III.Connect the connecting joint of lower helix cable and wiring harness of steering wheel.
1. Liking that shown in figure, align locking part of male joint and sliding block of female joint in same
direction to avoid mutual friction.
Supplemental restraint system--Note
 242 
Sliding block
Sliding block
Disconnect completely

IV. Assemble ECU joint
Figure 1 Figure 2 Figure 3
1. Press down limit switch in figure 1.
2. Dial white switch along the black line in figure 2, dial it to bottom liking that shown in figure3.
Hint: you will hear the assembling sound that shows it is put to position when white switch is
put into position.
V. Connect airbag wiring harness and short wiring harness at the side of passenger.
2. Confirm inserting it until locking, after assemble, pull it to check whether it is locked (when locking,
confirm exterior joint returns to former position, at the same time, assembling sound could hear).
Hint:
zWhen moving the sliding block, do not contact it.
zPay attention to do not distort the release board, if release board is distorted, it is neces-
sary to change it with new helix cable.
Figure 3 Figure 4
1. Insert the connector in figure 3 in the part in figure, after assemble it into its position, you will hear hint
sound.
Supplemental restraint system--Note
 243 
Sliding blockSliding block
Limit switch

2. Inspection for indicating light of safety airbag
(1) When set the ignition switch at ON position, confirm whether the indicating light illuminates.
(2) After illuminating for five seconds, confirm whether indicating light extinguishes forever.
(3) If starting ignition switch for five seconds, indicating light does not extinguish (flash or illuminate for long
time), confirm the position of system malfunction with special diagnostic tool according to the flash
situation of indicating light.
3. System diagnosis
Safety airbag controller (KD4.1) will implement a series of cycle diagnostic testing to check whether the
function of airbag system has been prepared completely. This test will prevent restraint system from
exploding wrongly and insure the necessary explosion in impact. If finding any malfunction, safety airbag
controller (KD4.1) will store a applicable malfunction code and turn on indicating light to indicate a mal-
function state to be easy to maintain.
4. Malfunction judgment
(1) Malfunction category
System malfunction could be divided into three categories: power supply malfunction, subassembly
assembling malfunction and ECU inner malfunction.
a. Power supply malfunction
Normal working voltage of ECU is 9-18 V, related working voltage is 12 V. When automobile key is
turned to ACC gear, ECU connects power and begins to self-check, indicating light extinguishes
after illuminating for five seconds, this shows there is not any malfunction in ECU and exterior
subassembly, they could work normally. When automobile power voltage is less than 9V or higher
than 18V, ECU will self-check again. If self-checking could pass, ECU works normally, and indicat-
ing light extinguishes; if self-checking could not pass, it is necessary to self-check again, this self-
checking could be made six times, if indicating light illuminates all the time after six times, there is
some malfunction in power supply.
b. Assembling malfunction of airbag subassembly
Assembling malfunction of airbag subassembly is that malfunction which only needs to change or
repair airbag subassembly without needing to change ECU, including the situation that airbag
subassembly is not connected completely. If happening this malfunction when connecting power
supply, indicating light will flash N times at first, then it will illuminate all the time until malfunction is
removed. If happening impact in malfunction term, ECU could explode the channel of good part
and record every malfunction when exploding.
c. Inner malfunction of controller
Inner malfunction is the malfunction happening in ECU body, when happening this malfunction,
ECU could not explode airbag, and will record the impacting acceleration.
Note: common repairer could not repair this inner malfunction, if happening this malfunction,
it is necessary to change ECU.
(2) Malfunction state display
Malfunction treatment
1. Basic procedure of malfunction diagnosis
zAfter assembling new electronic control unit of safety airbag system, indicating light of safety airbag
system will extinguish forever after flashing for 5 seconds when ignition switch is at state of ON, this
shows airbag system works normally. At this time, the system does not need to repair, it is necessary
to make system diagnosis and repair when showing any situation except this.
zIf indicating light of safety airbag system does not illuminate when ignition switch is at the state of ON,
check the related circuits of indicating light, then operate it to make it enter working state.
Supplemental restraint system--Malfunction treatment
 244 
Warning light illuminate Scanning ECU by connecting Find the malfunction Deal with Clean the code
and does not extinguish diagnostic instrument malfunction