2008 GEELY CK fuse

252(3)Check the connection between ECU and instrument cluster
1Turn the ignition switch to LOCK.
2Disconnect the negative (-) terminal cable from the battery.
3Disconnect the connector of instrument cluster.
4Check if the related circuits of the warning light are connected or not.
Yes: continue with next step.
No: replace the wire harness, and then continue with step 5.
2. SRS warning light remains on.DIAGNOSTIC PROCEDURESTo begin the check, first use special diagnostic instruments and ECU to perform communication diagnosis
and find out the causes of the trouble. If the communication fails, continue with the following procedures:
(1) Check battery
1Check battery voltage.
2Is voltage higher than 9V?
Yes: continue with next step.
No: Insufficient battery supply. Check the charging/discharging system, and then continue with step (5).
(2) Check the continuity of the wire harness between ECU and instrument cluster
1Turn the ignition switch to LOCK.
2Disconnect negative (-) terminal cable from the battery.
3Open the guard plate of the central passage.
4Disconnect the connector of the instrument cluster.
5Connect the negative (-) terminal cable of the battery.
6Turn the ignition switch ON.
7Check whether the voltage of the connector terminal of the instrument is 12V (power supply and instrument
connecting wire).Trouble Che cking Sta tus P ossible Causez Insufficient battery supplyz ECU internal troublez SRS wa rning light trouble of instrument c luste rz Improper connection of ECU connectorz P oor c ontac t of instrume nt c luste r c onne c torz Ope n circ uit or poor c onta c t of ECU power supply fusez P oor c onne c tion of ECU connec tor te rmina lz P oor conta ct of the wire ha rne ss be twe en ECU
connec tor te rmina l a nd groundz Drive r or pa ssenge r side circ uit trouble of SRS SRS wa rning light
remains onSRS warning light
remains on

2543.Internal trouble
4. Power troubleDIAGNOSTIC PROCEDURES(1) Check battery
yIs the battery voltage measured higher than 9V?
Yes: continue with next step.
No: low battery voltage, check the charging/discharging system.
ySee Chapter I, Charging System-Battery Checking
(2) Check the wire harness between battery and fuse box
yRemove fuse box and turn the ignition switch ON, without loosening connector.
yMeasure and see if the electrical potential between two terminals of the fuse box is more than 9V.
Yes: continue with next step.
No: check the wire harness.DTC B1620 Internal trouble of SRS unitCAUTION
●
Condition for running the DTC is to inspec t the dia gnostic trouble code that
ma y not a ppe a r prior to this te st. P e rforming this te st ma y re sults in body injury orda ma ge d system due to misoperations. The re fore , prepa ra tions must be ma debefore checking.
●
Internal circuit trouble of SRS ECU
P ossible Ca use Interna l trouble of SRS unit
Operation
Replace the SRS unit, see SRS System, Removal & Installation of SRS Unit Che c king ConditionsDTC B1112 Low power source voltage of SRS ECU
CAUTION
Condition for running the DTC is to inspe ct the diagnostic trouble c ode that ma y not
a ppea r prior to this test. P e rforming this te st ma y re sults in body injury or da ma ge dsyste m due to misoperations. Therefore, prepa ra tions must be ma de beforechecking.
●
The e lec tric a l pote ntia l be twe e n pins 5 a nd 6 of the c onne c tor of SRS unit is
le s s t ha n 9V .
●
Low batte ry volta ge
Trouble in wire ha rne ss betwe e n ba tte ry and SRS ECU C he c king C ondit ions
P os s ible C a us e

255(3) Check the wire harness between the fuse box and the connector of the SRS unit
CAUTION
If it is not handled properly, the airbag assembly may be triggered and deployed, leading to serious injury to a
person. Therefore, prior to handling, read the service cautions carefully. See service cautions for SRS.
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Remove glove box (along with passenger airbag assembly)
6Loosen passenger airbag assembly connectors.
7Remove left trim plate.
8Loosen all the SRS unit connectors.
9Reconnect the negative (-) terminal cable of the battery and turn ignition switch ON, check whether the
electrical potential between pins 5 and 6 (ground) of the connector of SRS unit is higher than 9V.
Yes: continue with next step.
No: replace the wire harness.
VTurn the ignition switch to LOCK. 11 Loosen the negative (-) terminal cable from the battery and wait for over 1 minute. 12 Remove left trim plate. 13 Disconnect the adaptor connector of SRS unit. 14 Reconnect the battery negative (-) terminal cable and turn the ignition switch ON, check whether the
voltage between the corresponding pin of the connector and the pin (ground) is higher than 9V.
Yes: completion of trouble diagnosis.
No: replace the wire harness.
5. Driver side troubleDTC
B1 346
B1 347
B1 348
B1 349
CAUTION
● If it is not handled properly, the airbag assembly may be triggered and deployed,leading to s erious injury to a person. Therefore, prior to handling, read the service cautionscarefu lly .
See s erv ice cau t io n s fo r SRS
If there is driver airbag
● The resistance between terminals of the SRS unit connectors is out of range.
The wire harness of the driver airbag of SRS is short or open circuited.
● Driv er airb ag as s emb ly tro u ble.
● Clock spring internal trouble.
● Trouble of the connector of the circuit between clock spring and SRS ECU.
● The wire harness between clock spring and SRS ECU is open or short-circuited.
● In co rrect in s ert io n o f t h e co n n ect o r o f t h e d riv er airb ag g en erat o r o f SRS. Driver airbag trouble (high or low resistance, short circuit, ground, etc.)
Ch e c kin g Co n d it io n s
Pos s ib le caus e

276Section 2 ABS System CheckI. DTC Problem Inspection TableNote: If the Battery is excessively discharged, the motor will not be driven, therefore you must
check that the battery voltage is normal before performing the motor driving test. The vehicle
must be stationary during the test. 1 DTC 01276 Like ly Causes
[De s cription]
When the vehicle speed exceeds
20km/h, A BS EC U de te c ts tha t the motor c a n not
ope ra te normally and re c ord this D TC.
[Hint]
Whe n this proble m oc c urs, one of the
possible causes is that the wire harness between
the motor and the ECU is disconnected. Use the
sc a n me te r to pe rform the te st by a c tiva ting the
H CU func tion to drive the motor.z P ow e r supply is disc onnec ted or grounde dz Motor w ire ha rne ss is disc onnec te dz Motor is da ma ge dRemove the motor wire harness connector, connect
it to the Battery to see whether the motor operates?Check the fuse and ABS ECU connectorConnect the motor wire harness connectorTurn the
ignition switch to ONClear the DTC Use the scan
meter to Perform the HCU diagnosistor
Turn the ignition switch to ONDoes the fault reoccur?Refer to “Occasional Problem Service Key Point” Normal
Normal
NoAbn.
Abn.
Ye sReplace the HCU
Replace the fuse or wire harness
Replace the ECU

281 6 DTC 00668 Like ly Cause s[De s cription]When powe r supply termina l 30
doe s not supply the volta ge or the volta ge is too
high, this DTC is se t.z ABS system fuse is broken
z Ba tte ry Volta ge too low or high
z ABS wire ha rne ss connec tor is da mage d
z ABS ECU is damagedCheck the ABS system 50A fuseDisconnect the ABS wire harness from the
ECU, turn the ignition switch to ON, mea-
sure the voltage among the following termi-
nals of the ABS wire harness
Terminal 8 and 9 9.5-16.5V
Terminal 24 and 25 9.5 - 16.5V
Terminal 8 and 4 9.5 -16.5V Check the ABS wire harness connectorRetest. Abn. again?Check the Battery voltage Refer to "Occasional Problem
Service Key Points"Replace the ABS ECU
Abn.Abn.
Ok
Ok
Ok
Ye s NoReplace the fuse
Repair the connector Abn.

283II. Non-DTC Problem Inspection Table1 With ignition s witch ON (Engine Off),
the AB S warning lig ht do e s no t g o o nLike ly Caus e s[De s cription] ABS Wa rning Light doe s not go
on, the like ly c a use ma y be the ope n in the
warning light powe r supply c irc uit, burne d bulb
or dama ged wa rning light drive module .z Burned fuse
z A B S W a r ning L ight B ulb bur ne d
z Power supply circuit open
z ABS Wa rning Light Drive Module da mage dCheck the ABS warning light
fuse in the fuse blockRemove the ECU connector,
does the warning light goes on
with the ignition switch ON? Check whether the ABS
warning light is burnedCheck whether the warn-
ing light power supply cir-
cuit and ground circuit in the
wire harness is openCheck the connector of the
warning light power supply
circuit and ground circuit in
the wire harness Does the fault reoccur?Abn.
Replace
Repair the wire harnessNo
Ye s
Abn.
Abn. Ok
Ye s No
Ok
OkReplace
Repair the wire
harness
Repair the connectorCheck whether the wire in the
ABS wire harness connecting
the ABS warning light drive
module and the ECU is short
to ground Ye s Replace the warning light
drive module Ye sNoRefer to "Occa-
sional Problem
Service Key Points"

288 6 No DTC output
（can no t
communicate with the s can me te r
）Lik e ly Caus e s
[De s cription]
It ma y be the ABS ECU powe r
supply c ircuit or dia gnosis wire circ uit tha t c an
not communicate with the scan meterz Burned fuse
z Diagnosis wire broke n or connec tor disc onne c ted
z Damaged ABS ECU
z Scan meter faultyCan the scan meter commu-
nicate with the MK-20 ABS
ECU on other vehicles? ABS scan meter faulty, check it af-
ter repairing itReplaceCheck the power cable, ground wire
and diagnostic wire in the diagnos-
tic interface Check the diagnostic interface or wire harness No
Ye s
No
Ye s
ContinuityCheck ABS power supply
fuse OkReplace the ABS ECURepair the
diagnostic
interface or
harnessIs there any scan meterAbn.Remove the ABS ECU
connector, check whether
there is continuity between
terminal 7 in the ABS wire
harness and the terminal 8 in
the diagnostic interfaceAbn.NoNo

303Figure 6 A/C System Electrical Appliance DiagramIII. Protecting Device1. Low temperature protection
Evaporator temperature sensor, when the sensed temperature is lower than 3°C, the compressor clutch
is de-energized and stops operation.
2. High temperature protection
Water temperature sensor, when the sensed water temperature reaches 109°C, the compressor clutch is
de-energized and stops operation.
3. Low pressure protection
When pressure sensed by the pressure switch is lower than 0.25MPa, the compressor clutch is de-
energized and stops operation.
4. Voltage protection
When the pressure sensed by the pressure switch reaches 1.7MPa, radiator fan rotates.
5. High pressure protection
When the pressure sensed by the pressure switch reaches 2.6MPa, the compressor clutch is de-energized
and stops operation.
6. Normal pressure
When system pressure reaches 0.25MPa~2.4MPa, control the A/C idle speed. Color of wire:R-Red Bl-Blue Y-Yellow Lg-Light green Br-Brown B-Black P-Pink G-Green W-White Gr-Gray
1. Battery 2. Main Fuse Box 3. Alternator 4. Ignition Switch 5. Idle Rise Valve 6. Blower 7. Relay
8. Blower Regulating Resistance 9. Blower Switch 10. A/C Switch 11. A/C Low Pressure Switch
12. Compressor 13. Condensor Fan 14. Radiator Fan 15. A/C High Pressure Switch
16. Water Temperature Sensor 17. Evaporator Temperature Sensor 18. Electronic Wind Door Actuator Switch
19. Electronic Wind Door Actuator 20. Revolution Sensor 21. Engine ECU