2008 DODGE SPRINTER tow

117 Controls in detailSeats
3
The driver’s and passenger’s seat can be
rotated by 180° to be opposite of the di-
rection of travel.The seats engage in the direction of trav-
el or opposite the direction of travel as
well as at 50° pointing towards the exit.Fold the handbrake lever down as far as
it will go. You could otherwise damage
the handbrake or the handbrake lever.
\1
Make sure the handbrake is applied
and the handbrake lever is folded
down as far as it will go
(\2
page 191).
\1
Set the steering wheel so that there
is sufficient clearance for turning and
adjusting the driver’s seat
(\2
page 127).
Warning
G
The driver’s and passenger’s seat must be
adjusted and properly engaged in the di-
rection of travel for driving. Otherwise you
will not be able to operate the vehicle
safely.
The restraint systems in your vehicle will
only function as intended when the dri-
ver’s and passenger’s seat are engaged in
the direction of travel.
!
CAUTION
When rotating the seats, make sure
there is sufficient space. If neces-
sary, move the seat fore or aft to
avoid colliding with adjacent add-on
parts.
\4
Fold the handbrake lever down
as far as it will go. You could
otherwise damage the handbra-
ke or the handbrake lever.
iMove the passenger’s seat forward
as far as it will go before rotating it
(\2
page 114).
nf_BA.book Page 117 Friday, January 25, 2008 3:53 PM

120 Controls in detailSeats
3
\1
Pull the seat cushion towards the
front slightly and out of rear
anchorage
2
.
\1
Fold the seat cushion up by the rear
edge.
Positioning the seat cushion
\1
Fold the seat cushion back.
\1
Slide the seat cushion under the
backrest and into rear
anchorage
2
.
\1
Fold the seat cushion down.
\1
Press the front of the seat cushion
down until it engages in front
anchorage
1
.
1To fold up the armrest
2To unlock the armrest
3To move the armrest to the desired posi-
tion
iYou can store various articles in the
space under the twin passenger’s
seat.
Armrests*
nf_BA.book Page 120 Friday, January 25, 2008 3:53 PM

184 Controls in detailDriving and parking
3
You will find information on:\4
regular checks (
\2
page 312)
\4
driving in winter (
\2
page 406)
\4
driving when towing a trailer
(\2
page 303)
\4
and other driving tips
in the “Operation” section
(
\2
page 301).
\1
Before starting the engine, make
sure that all vehicle occupants are
wearing their seat belt correctly
(\2
page 39) and the handbrake
(
\2
page 191) is applied.
Starting the engineWarning
G
Never run the engine in an enclosed
space. The exhaust fumes contain poi-
sonous carbon monoxide. Breathing in
exhaust fumes constitutes a health haz-
ard and can lead to loss of consciousness
and death.
Warning
G
A seat belt that is worn incorrectly or not
at all, or that is not correctly engaged in
the seat belt buckle, cannot perform its
intended protective function. In certain
circumstances, you could then be seri-
ously or even fatally injured. Make sure,
therefore, that all occupants – in particu-
lar, expectant mothers – wear their seat
belt correctly at all times.
nf_BA.book Page 184 Friday, January 25, 2008 3:53 PM

188 Controls in detailDriving and parking
3
Do not accelerate to prevent your vehi-
cle from rolling backwards on an uphill
gradient. Instead, you should either use
the handbrake or depress the brake ped-
al. This prevents excessive wear on the
clutch.
Select a lower gear (shift range
3, 2 or
1)
(
\2
page 204) in good time on long and
steep downhill gradients, especially if
towing a trailer. This prevents the brakes
from overheating and wearing too rapidly.
It is best not to stop the vehicle immedi-
ately after the brakes have been subject-
ed to an extreme load; continue driving
for a short time instead. The brakes are
cooled down more quickly in the airflow.The first time the brakes are applied af-
ter a long period of driving in heavy rain
without braking, it is possible that:
\4
there will be a delayed braking
response
\4
you will need to depress the brake
pedal more firmly
You should therefore maintain a greater
distance from the vehicle in front.
BrakingWarning
G
There is no power assistance for the ser-
vice brake when the engine is not running.
You will need to use significantly more
force to brake and could therefore lose
control of the vehicle and cause an acci-
dent.
Never switch off the engine while driving.
Warning
G
Make sure that other road users are not
put at risk by your braking.
nf_BA.book Page 188 Friday, January 25, 2008 3:53 PM

193 Controls in detail
Driving and parking
3
Stopping the engine\1
Apply handbrake (
\2
page 191).
\1
Move selector lever to
P.
\1
Turn key to position
0 (\2
page 111)
in the ignition lock and remove it.
The immobilizer is activated.
\1
Secure the vehicle at the front axle if
unloaded and at the rear axle if load-
ed, e.g. using a chock (
\2
page 521).
Warning
G
The wheels on the rear axle could lock if
the handbrake lever is applied too abrupt-
ly. The vehicle could then start to skid.
Make sure that you apply the handbrake
lever carefully to ensure that braking ap-
plication is moderated.
!
CAUTION
If the coolant temperature is raised,
e.g. following driving in mountainous
terrain, run the engine at idling speed
for a further 1 or 2 minutes before
you switch off the engine. This allows
the coolant temperature to return to
normal again.
iWhen parking on steep uphill or
downhill gradients, turn the front
wheels towards the curb.
iYou can only remove the key from
the ignition lock when the selector le-
ver is in position
P.
nf_BA.book Page 193 Friday, January 25, 2008 3:53 PM

196 Controls in detailDriving and parking
3
\4
causes and consequences of tire
wear
\4
measures to be taken in the event of
tire damage
\4
tire types for certain regions, areas
of operation or conditions of vehicle
use
\4
interchangeability of tires, etc.
Modifications to the brake system or
wheels are not permissible, nor is the
use of spacer plates or brake dust
shields. Any such modifications will in-
validate the vehicle’s general operating
permit.Treadwear indicators (TWI) are required
by law. These indicators are located in
six places on the tread circumference
and become visible at a tread depth of
approximately 1/16 in (1.6 mm), at
which point the tire is considered worn
and should be replaced.
The Treadwear Indicator appears as a
solid band across the tread.
Warning
G
If you feel a sudden significant vibration
or ride disturbance, or you suspect that
possible damage to your vehicle has oc-
curred, you should turn on the hazard
warning flashers, carefully slow down,
and drive with caution to an area which is
a safe distance from the road.
Inspect the tires and the vehicle undercar-
riage for possible damage. If the vehicle
or tires appear unsafe, have the vehicle
towed to the nearest authorized Sprinter
Dealer or tire dealer for repairs.
nf_BA.book Page 196 Friday, January 25, 2008 3:53 PM

201 Controls in detail
Automatic transmission
3
\3 Automatic transmissionP Parking position (selector lever lock)R Reverse gearN NeutralD Drive positionThe automatic transmission adapts to
your individual driving style by continu-
ously adjusting its shift points. These
shift point adjustments take into ac-
count the current operating and driving
conditions.
If the operating or driving conditions
change, the automatic transmission re-
acts by adjusting the gearshift program.The individual gears are selected auto-
matically. The gear selected depends
on:
\4
the selector lever position in shift
ranges
D, 4, 3, 2 and
1 (\2
page 204)
\4
the position of the accelerator pedal
(\2
page 205)
\4
the road speed
\4
resistance (load, uphill gradient,
trailer towing)
Gearshift pattern
Gearshift procedure
nf_BA.book Page 201 Friday, January 25, 2008 3:53 PM

202 Controls in detailAutomatic transmission
3
The selector lever position engaged or
the current shift range is shown in the
display. Display on vehicles with steer-
ing wheel buttons* (
\2
page 151) and on
vehicles without steering wheel buttons
(
\2
page 147).
When the selector lever is in position
D,
you can influence the gearshifts made
by the automatic transmission by:
\4
restricting the shift range
\4
changing gear yourself
Selector lever positionsì

Parking lock

Prevents the parked vehicle
from rolling away. Only move
the selector lever to
P when
the vehicle is stationary.
You can only remove the key
when the selector lever is in
position
P. The selector lever
is locked in position
P when
the key is removed.
í

Reverse gear

Only move the selector lever
to
R when the vehicle is sta-
tionary.
ë

NeutralNo power is transmitted from
the engine to the drive
wheels. Releasing the brakes
will allow you to move the ve-
hicle freely, e.g. by pushing or
towing.Do not move the selector le-
ver to
N while the vehicle is in
motion. The automatic trans-
mission could otherwise be
damaged.
nf_BA.book Page 202 Friday, January 25, 2008 3:53 PM