2008 DODGE SPRINTER bulb

525 Practical hints
Changing bulbs
5
\3 Changing bulbsBulbs and lights are an important aspect
of vehicle safety. For this reason, make
sure that all bulbs are in working order at
all times.\4
Switch off the lights to avoid a short
circuit.
\4
Only touch new bulbs with a clean
lint-free cloth or something similar.
Do not work with wet or greasy fin-
gers.
\4
Only fit 12 V bulbs of the same type
as before and of the correct wattage.
\4
Have the headlamp setting checked
regularly.
\4
If the newly installed bulb does not
light up either, visit an authorized
Sprinter Dealer.
\4
Have the following LEDs and bulbs
changed at an authorized Sprinter
Dealer:\4
The additional turn signals in the
exterior mirrors
\4
The third brake lamp (cargo and
passenger vans only)*
\4
The bi-xenon headlamps*
\4
The foglamps*
Before changing bulbs
Warning
G
Bulbs and bulb holders can become very
hot. For this reason, allow the light to cool
down before changing the bulb.
Keep bulbs out of the reach of children.
Never use a bulb which has been dropped.
Such a bulb may explode and injure you.
H7 bulbs are pressurized and may ex-
plode when changed. You should there-
fore wear eye protection and gloves when
you are changing them.
nf_BA.book Page 525 Friday, January 25, 2008 3:53 PM

526 Practical hintsChanging bulbs
5

\1
Switch off the lighting.
\1
Open the hood (
\2
page 318).
Front bulbs
Bulb
Model
1
Additional turn sig-
nal
PY 16 W
2
Turn signal
PY 21 W
3
Halogen headlamp:
low-beam headlamp
H7 55 W
Bi-xenon headlamp*:
low-beam
headlamp / high-
beam headlamp
D1S-35 W
4
Halogen headlamp:
high-beam headlamp
H7 55 W
Cornering lamp*
(Canada only)
H7 55 W
5
Foglamp*
H11 55 W
Bulb
Model
6
Parking lamp/side
marker/standing
lamp (Canada only)
WY 5 W
Bulb
Model
nf_BA.book Page 526 Friday, January 25, 2008 3:53 PM

527 Practical hints
Changing bulbs
5
Bi-xenon headlamps* High-beam headlamps, low-beam
headlamps
1Catches
2Housing cover
Warning
G
Xenon bulbs carry a high voltage. You
could receive a serious or fatal electric
shock if you touch the electrical contacts
on the xenon bulbs. Do not remove hous-
ing cover 2 (\2page 527) if the head-
lamps are xenon headlamps.
Continued
Warning (Continued)
G
Do not change xenon bulbs yourself.
Instead, always have them changed at an
authorized Sprinter Dealer which has the
necessary specialist knowledge and tools
to carry out the work required.
The manufacturer recommends that you
use an authorized Sprinter Dealer for this
purpose. In particular, work relevant to
safety or on safety-related systems must
be carried out at an authorized Sprinter
Dealer.
nf_BA.book Page 527 Friday, January 25, 2008 3:53 PM

528 Practical hintsChanging bulbs
5
\1
Press catches
1
down.
\1
Swing housing cover
2
in the direc-
tion of the arrow and remove it.
3Low-beam headlamps
4Halogen high-beam headlamps/xenon
headlamp cornering lamp*
\1
Pull the connector off the bulb hold-
er.
\1
Unclip the retainer spring and re-
move the bulb.
\1
Insert the new bulb such that the
base locates in the recess of the bulb
holder.
\1
Clip on the retainer spring and plug
the connector onto the bulb.
\1
Insert housing cover
2
into lower
brackets.
\1
Swing housing cover
2
toward
headlamp casing.
\1
Pull first the inner and then the outer
catch
1
upward until it audibly en-
gages in place.
Turn signals1Bulb holder
nf_BA.book Page 528 Friday, January 25, 2008 3:53 PM

529 Practical hints
Changing bulbs
5
\1
Turn bulb holder
1
and the bulb
counterclockwise and remove the
holder.
\1
Press down on the bulb, turn it coun-
terclockwise and remove it from bulb
holder
1
.
\1
Press the new bulb into bulb
holder
1
and screw it in clockwise.
\1
Place bulb holder
1
into the lamp
and turn it clockwise.
Parking lamps/side marker 1Cap\1
Turn cap
1
counterclockwise and
remove it.
\1
Remove the bulb holder together
with the bulb.
\1
Pull the bulb out of the bulb holder.
\1
Press the new bulb into the bulb
holder.
\1
Insert the bulb holder with bulb into
the reflector.
\1
Replace cap
1
and turn it clockwise
to the stop.
nf_BA.book Page 529 Friday, January 25, 2008 3:53 PM

530 Practical hintsChanging bulbs
5
Panel van/crewbusExample illustration of chassisRear bulbs
N82.10-2529-31
Bulb
Model
1
Third brake lamp
LED
2
Brake lamp
P21W
3
Turn signal
PY 21 W
4
Tail lamp /
side marker/Stand-
ing lamp (Canada
only)
R5W
5
License plate lamp
W5W
6
Rear foglamp (driv-
er’s side)
P 21 W
7
Reverse lamp
P 21 W
nf_BA.book Page 530 Friday, January 25, 2008 3:53 PM

531 Practical hints
Changing bulbs
5
Changing the rear bulbs (van /crewbus)\1
Switch off the lighting.
Rear lamp units1Securing screws
\1
Undo screws
1
and remove the rear
lamp unit in the direction of the ar-
row.
\1
Remove the connector.
Bulb
Model
8
Perimeter lamp/side
marker
R5W
9
Turn signal
PY 21 W
a
Brake lamp
P21W
b
Reverse lamp
P21W
c
Rear foglamp
(driver’s side)
P 21 W
d
Tail lamp
R5W
e
License plate lamp
R5W
nf_BA.book Page 531 Friday, January 25, 2008 3:53 PM

532 Practical hintsChanging bulbs
5
2Retaining lugs
3Brake lamp
4Side marker, Standing lamp (Canada
only), tail lamp
5Reverse lamp
6Turn signal lamp
7Rear foglamp (driver’s side)\1
Release retaining lugs
2
and re-
move the bulb holder from the rear
lamp unit.
\1
Press down on the bulb, turn it coun-
terclockwise and remove it from the
holder.
\1
Press the new bulb into the bulb
holder and screw it in clockwise.
\1
Plug the connectors into the bulb
holder.
\1
Fit the rear lamp unit.
To do this, clip the bulb holder into
the three holes provided on the side
and tighten screws
1
.
nf_BA.book Page 532 Friday, January 25, 2008 3:53 PM