2008 Citroen C4 engine
[x] Cancel search: enginePage 64 of 257
63
IV
A C C E S S
If you decide to drive with the doors locked, remem-ber that in the event of an accident this renders a c c e s s m o r e d i f fi c u l t f o r t h e emergency services.
Locking the doors from the inside
With the doors closed, press button B once to operate the electric central locking and unlocking.
The doors can still be opened from inside.
The central locking will not operate if a door is open, or not properly closed.
The lamp on the control B can signal any of 3 statuses:
- I t fl a s h e s i f t h e d o o r s a r e o p e n when the vehicle is stationary, engine stopped.
- It lights up if the doors are locked and the ignition is switched on.
- It goes out if the doors are not locked.
DOORSNote: Control B is inactive if the vehicle has been locked with the remote control or with the key.
Personal security
When the vehicle is started, the system automatically locks the doors and tailgate as soon as you reach a speed of approx. 10 km/h (6 mph).
Note: If a door is opened, this door will automatically relock as soon as the vehicle reaches approx. 6 mph.
Activation/Deactivation of the function
After switching on the ignition, give a long press on the central unlocking button until a message is displayed.
This allows from the front, deactivation of the opening of the rear doors and the use of the rear windows.
It is activated by means of a press on control A located on the electric windows control panel. The warning lamp in the instrument panel lights up for approx. 10 seconds.
Each time the ignition is switched on, the warning lamp comes on for approx. 10 seconds.
Opening of the doors from the outside and operation of the rear electric windows remain possible from the front of the vehicle.
Electric child safety
Page 105 of 257
98
IX
D R I V I N G
Manual gearbox
- Ensure that the gear lever is in the neutral position.
- D o n o t t o u c h t h e a c c e l e r a t o r .
- I n t h e c a s e o f d i e s e l e n g i n e vehicles: turn the key to the drive p o s i t i o n . W a i t f o r t h e p r e - h e a t e r warning lamp to go off, if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine starts (but not for more than ten seconds).
- I n t e m p e r a t u r e s l o w e r t h a n 0 ° C , apply the clutch during the action on the starter in order to aid starting. Then release the clutch slowly.
DO NOT RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
Automatic gearbox
- C h e c k t h a t y o u a r e i n p o s i t i o n P or N.
- D o n o t t o u c h t h e a c c e l e r a t o r .
- F o r D i e s e l e n g i n e s : t u r n t h e k e y t o position M . W a i t f o r t h e p r e - h e a t e r warning lamp to go off if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine turns over (not for longer than ten seconds).
Advice
Vehicles equipped with a Turbo:
Turbo equipped engines MUST be allowed to return to idle for several seconds before switching off the ignition. Failure to do so could cause serious damage to the turbo unit.
Flicking the throttle pedal as the ignition is turned off can lead to severe damage to the turbo unit.
(6 speed) Electronic Gearbox System
- C h e c k t h a t y o u a r e i n p o s i t i o n N.
- F u l l y d e p r e s s t h e b r a k e p e d a l .
- D o n o t t o u c h t h e a c c e l e r a t o r .
- F o r D i e s e l e n g i n e s : t u r n t h e k e y t o position M . W a i t f o r t h e p r e - h e a t e r warning lamp to go off if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine turns over (not for longer than ten seconds).
Note: If the vehicle has been stationary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
STARTING
Page 106 of 257
98
IX
D R I V I N G
Manual gearbox
- Ensure that the gear lever is in the neutral position.
- D o n o t t o u c h t h e a c c e l e r a t o r .
- I n t h e c a s e o f d i e s e l e n g i n e vehicles: turn the key to the drive p o s i t i o n . W a i t f o r t h e p r e - h e a t e r warning lamp to go off, if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine starts (but not for more than ten seconds).
- I n t e m p e r a t u r e s l o w e r t h a n 0 ° C , apply the clutch during the action on the starter in order to aid starting. Then release the clutch slowly.
DO NOT RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
Automatic gearbox
- C h e c k t h a t y o u a r e i n p o s i t i o n P or N.
- D o n o t t o u c h t h e a c c e l e r a t o r .
- F o r D i e s e l e n g i n e s : t u r n t h e k e y t o position M . W a i t f o r t h e p r e - h e a t e r warning lamp to go off if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine turns over (not for longer than ten seconds).
Advice
Vehicles equipped with a Turbo:
Turbo equipped engines MUST be allowed to return to idle for several seconds before switching off the ignition. Failure to do so could cause serious damage to the turbo unit.
Flicking the throttle pedal as the ignition is turned off can lead to severe damage to the turbo unit.
(6 speed) Electronic Gearbox System
- C h e c k t h a t y o u a r e i n p o s i t i o n N.
- F u l l y d e p r e s s t h e b r a k e p e d a l .
- D o n o t t o u c h t h e a c c e l e r a t o r .
- F o r D i e s e l e n g i n e s : t u r n t h e k e y t o position M . W a i t f o r t h e p r e - h e a t e r warning lamp to go off if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine turns over (not for longer than ten seconds).
Note: If the vehicle has been stationary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
STARTING
Page 108 of 257
98
IX
D R I V I N G
Manual gearbox
- Ensure that the gear lever is in the neutral position.
- D o n o t t o u c h t h e a c c e l e r a t o r .
- I n t h e c a s e o f d i e s e l e n g i n e vehicles: turn the key to the drive p o s i t i o n . W a i t f o r t h e p r e - h e a t e r warning lamp to go off, if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine starts (but not for more than ten seconds).
- I n t e m p e r a t u r e s l o w e r t h a n 0 ° C , apply the clutch during the action on the starter in order to aid starting. Then release the clutch slowly.
DO NOT RUN THE ENGINE IN A SPACE THAT IS ENCLOSED OR INSUFFICIENTLY VENTILATED.
Automatic gearbox
- C h e c k t h a t y o u a r e i n p o s i t i o n P or N.
- D o n o t t o u c h t h e a c c e l e r a t o r .
- F o r D i e s e l e n g i n e s : t u r n t h e k e y t o position M . W a i t f o r t h e p r e - h e a t e r warning lamp to go off if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine turns over (not for longer than ten seconds).
Advice
Vehicles equipped with a Turbo:
Turbo equipped engines MUST be allowed to return to idle for several seconds before switching off the ignition. Failure to do so could cause serious damage to the turbo unit.
Flicking the throttle pedal as the ignition is turned off can lead to severe damage to the turbo unit.
(6 speed) Electronic Gearbox System
- C h e c k t h a t y o u a r e i n p o s i t i o n N.
- F u l l y d e p r e s s t h e b r a k e p e d a l .
- D o n o t t o u c h t h e a c c e l e r a t o r .
- F o r D i e s e l e n g i n e s : t u r n t h e k e y t o position M . W a i t f o r t h e p r e - h e a t e r warning lamp to go off if it is on.
- A c t i o n t h e s t a r t e r b y t u r n i n g t h e key until the engine turns over (not for longer than ten seconds).
Note: If the vehicle has been stationary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
STARTING
Page 111 of 257
1 0 1
IX
D R I V I N G
Neutral
If the vehicle is moving, do not select this position, even momentarily.
Reverse gear
Only engage reverse gear when the vehicle is stationary.
If the vehicle is moving at a very low speed, if reverse gear is requested (position R) this will be taken into account only when the vehicle comes to a halt.
The "foot on brake" warning lamp m a y fl a s h i n t h e i n s t r u m e n t p a n e l to remind you to brake.
If the vehicle is moving at a high speed, if reverse gear is requested the warning lamp "N" w i l l fl a s h a n d your vehicle will go automatically i n t o n e u t r a l . T o r e - e n g a g e a g e a r , you have only to return the gear lever to position A or M.
A sound signal indicates when reverse gear is engaged.
If parking assistance is deactivated, the sound signal for reverse gear engaged is absent.
The engine can only be started if the brake pedal is pressed and the gear lever is in position N.
The warning lamp "foot on b r a k e " fl a s h e s o n t h e d i s p l a y .
With the engine running, before accelerating away check the position engaged by looking at the lever grille or the rev counter : R, A or M.
If you are stationary with the engine running, take care to leave your gear selector in position N.
Sport option
Activation
Press on button S, situated on the lever grille.
The warning lamp "S" displays on the rev counter.
This option can be activated either in automatic mode or in manual mode.
Deactivation
Press again again on button S on the lever grille.
The warning lamp "S" disappears on the rev counter.
Note: the Sport option is deactivated whenever you switch off the ignition.
Automatic mode
Manual mode
- P u s h t h e l e v e r t o c h a n g e t o a higher gear.
- P u l l t h e l e v e r t o c h a n g e t o a l o w e r gear.
Page 112 of 257
1 0 2
IX
D R I V I N G
Starting the vehicle
- T o s t a r t t h e e n g i n e , t h e g e a r l e v e r has to be in position N.
- F u l l y d e p r e s s t h e b r a k e p e d a l .
- A c t i o n t h e s t a r t e r .
- W i t h t h e e n g i n e r u n n i n g , d e p e n d i n g on your preference place the lever on R, A or M.
- C h e c k t h e p o s i t i o n e n g a g e d o n t h e rev counter.
- R e l e a s e t h e h a n d b r a k e .
- R e l e a s e t h e b r a k e p e d a l a n d accelerate.
If the lever is not in position N, the warning lamp "N" fl a s h e s o n t h e r e v counter.
If the brake pedal is not pressed down, the warning lamp "Foot on brake" fl a s h e s i n t h e i n s t r u m e n t panel.
In both cases, the engine does not start; recommence the above procedure.
Note: If the vehicle has been stationary for a long time, or if you have pressed the brake pedal a number of times while stationary, it will be necessary to press the brake pedal hard down in order to authorise the engine to start.
Stopping the engine
Before switching the engine off, you can choose:
- t o l e a v e t h e v e h i c l e i n n e u t r a l ; f o r that, place the lever in position N,
- t o l e a v e t h e v e h i c l e w i t h a g e a r engaged (R, A or M); for that, place the lever in the position chosen. In this case, the vehicle cannot be moved.
In all cases, it is essential to apply the handbrake.
Before undertaking any operation in the engine compartment, make absolutely sure that the gearbox is in neutral and that the handbrake is on.
Do not hold the vehicle stationary using only the accelerator.
If you are stopped on an incline, use the handbrake to hold the vehicle.
Acceleration
To obtain optimum acceleration (for example to overtake another vehicle), you have only to press the pedal hard down to go beyond the e n d - o f - t r a v e l s w i t c h .
Page 114 of 257
IX
D R I V I N G
Manual mode
Position the gear lever in position M, then:
- p u s h t h e l e v e r t o e n g a g e a h i g h e r gear,
- p u l l t h e l e v e r t o c h a n g e d o w n .
Manual mode with controls behind the steering wheel
Place the gear lever in position M, and then the controls at the steering wheel will give you access to the six gears in forward drive.
To change gear:
- P r e s s b e h i n d t h e c o n t r o l "+" at the steering wheel to engage a higher gear.
- P r e s s b e h i n d t h e c o n t r o l "-" at the steering wheel to change down.
Observations:
When the vehicle is braking or reducing speed, the gearbox changes down automatically to a suitable gear.
In manual mode, it is not necessary to release the accelerator during changes of gear.
C h a n g e s o f g e a r a r e a c c e p t e d o n l y if consistent with engine speed.
Under heavy accelera-tion, a higher gear will only be engaged when the driver actions the gear lever or the controls at the steering wheel.
Note: These controls at the steering do not permit you to select neutral or reverse gear.
Page 118 of 257
1 0 7
IX
D R I V I N G
Drive
The gearbox always selects the gear best adapted to the following parameters:
- s t y l e o f d r i v i n g ,
- r o u t e p r o fi l e ,
- v e h i c l e l o a d .
In this way the gearbox operates in autoadaptive mode, without the need for your intervention.
For certain manoeuvres (for example overtaking), it is possible to ob tain maximum acceleration by pressing hard down on the accelerator pedal, which may trigger automatic changedown to a lower gear.
Note
During braking, the gearbox may kick down automatically in order to offer an effective engine brake.
If you rapidly lift your foot off the accelerator, the gearbox will guard your safety by not changing up again.
Sequential forward drive
Selector position for manual gear changing.
- S e l e c t o r a t M.
- P u s h t h e s e l e c t o r t o w a r d s t h e s i g n "+" to change up a gear.
- P u l l t h e s e l e c t o r t o w a r d s t h e s i g n "-" to change down a gear.
Note: Passage from one gear to another is only possible when vehicle speed and engine speed permit.
The Sport and Snow programmes are not operative in sequential mode.
The change from position D (drive in automatic mode) to position M (drive in sequential mode) or vice versa may be effected at any time.