-Emergency situations PW--------=----=---------------
4. Connect clamp on opposite end of negative cable to the
negative(-) terminal© of the discharged vehicle battery
@.
- Check that all screw plugs on the battery cells are
screwed in firmly. If not, tighten plugs prior to
connecting clamp on negative battery terminal.
Starting the engine
-Start the engine of the vehicle with the booster battery.
Run the engine at a moderate speed.
- Start engine with discharged vehicle battery in the usual
manner .
- If the engine fails to start: do not keep the starter
cranking for longer than 10 seconds. Wait for about 30
seconds and then try again.
- With engine running, remove jumper cables from both
vehicles in exact
reverse order.
The battery is vented to the outside to prevent gases from entering
the vehicle interior.
Make sure that the jumper clamps are well connected with their
metal parts in full contact with the battery terminals .
& WARNING
To avoid serious personal injury and damage to the vehicle, heed
all warnings and instructions of the jumper cable manufacturer. If
in doubt, call for road service.
• Jumper cables must be long enough so that the vehicles do not
touch.
• When connecting jumper cables, make sure that they cannot
get caught in any moving parts in the engine compartment.
& WARNING (continued)
• Before you check anything in the engine compartment, always
read and heed all
WARNINGS:::::, page 265, "Engine compartment".
0 Note
Improperly connected jumper cables can damage or destroy the
generator .
• Always connect POSITIVE (+l to POSITIVE(+), and NEGATIVE (-l to
NEGATIVE (- l terminal.
• Check that all screw plugs on the battery cells are screwed in
firmly. If not, tighten plugs prior to connecting clamp on negative
battery terminal.
• Please note that the procedure for connecting a jumper cable as
described above applies specifically to the case of your vehicle
being jump started. When you are giving a jump start to another
vehicle, do not connect the minus 1-1 cable to the minus (-1 terminal
on the discharged battery @::::, page 331, fig. 234. Instead, securely
connect the minus (-l cable to either a massive metal component
that is firmly bolted to the engine block or to the engine block itself .
If the battery that is being charged does not vent to the outside,
escaping battery gas could ignite and explode! •
Emergency towing with commercial
tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by commercial tow truck
operators who know how to operate their equipment safely.
• Never tow your Audi, towing will cause damage to the engine
and transmission. .,_
Emergency situations -
----------------=-=---
Rear hook up
These s te p s app ly fo r w in chi ng the vehi cle on to a car
c arr ier w ith the re a r f ir st.
- Have the vehic le ali gne d cent ered wi th the ca r carr ier
r a mp.
- Attach the win ch hook to t he
rear to wline eye
=> pa ge 334, fig. 237 .
- On ce th e ca r is po sit io ned on t he car ca rrie r, ha ve safety
c hain (s ) a ttach ed t o the
fron t towline eye => pag e 333an d
ti ghte ned .
[ i] Tips
Chec k carefu lly to ma ke sure the veh icle is hoo ked up securel y
b ef ore mov ing the ca r up the ca r ca rrier r amp. •
Lifting the vehicle
Important safety precautions
Be aware of the following hazards before l ift ing the vehic le w ith a
w ork sho p ho is t or f lo or jack :
• The vehicle should never be lifted or jacked up from underneath
the engine oil pan, the transmission housing , the front or rear axle
or the body side members . This could lead to serious damage.
• Use lifting equipment with padded contact surfaces to avoid
damage to the underbody or chassis frame.
• Alternatively, cover the contact surfaces on workshop hoist or
floor ja ck with rubber pads before lifting.
• Before driving over a workshop hoist , check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist. •
Before driving over a workshop hoist , ensure that there is suffi
cient clearance between the hoist and low parts of the vehicle .
& WARNING
To reduce the risk of serious injury and vehicle damage:
• Always lift the vehicle only at the special workshop hoist and
floor jack lift points illustrated
=> fig . 239 and => fig . 240 .
• Failure to lift the vehicle at these points could cause the vehicle
to tilt or fall from a lift if there is a change in vehicle weight distri
bution and balance . This might happen, for example, when heavy
components such as the engine block or transmission are
removed .
• When removing such heavy components, anchor vehicle to
hoist or add corresponding weights to maintain the center of
gravity . Otherwise , the vehicle might tilt or slip off the hoist ,
causing serious personal injury .
•
Do-it -yourself service
ffl,...__G_ e_ n_ e_r_a _ l_ i
_ n_ f_ o_ rm_ a
_ t_io _ n _______________________________________________ _
General information
Explanation of technical data
Some of the technical data listed in this manual require
further explanation.
The technical da ta for your vehicle are listed in the charts starting
on => page 343. This chapter p rovides general information, notes
and restrictions which apply to these data. •
Vehicle identification
The key data ore given on the vehicle identification
number (VIN) plate and the vehicle data sticker.
Fig . 241 Vehicle Identi
fication Number (VIN)
plate: location on
driver's side dash
panel Fig
. 242 The vehicle
identification label
-
inside the luggage
compartment
The Vehicle Identification Number (VIN}
is located on the driver's side so that it is visible from the outside
through the windshield -
see:::::, fig. 241.
The vehicle identification label
is located in the luggage compartment in the spare wheel well.
The
label => fig. 242 shows the following vehicle data:
G) Production control no.
0 Vehicle identification no .
© Type code number
© Type designation/engine output in Kilowatts
© Engine and transmission code letter
© Pain t no./lnt erior
0 Optional equipment no.'s
Vehicle data 2 to 7 are also found in your Maintenance
& Warranty
booklet .
..,.
_____________________________________________________ D_a_ t_ a _ ___.11111
Data
Ap plies to vehicles : w ith 2 .0 lite r 4-cyl. engine
200 hp, 2.0 liter 4-cyl. turbo engine
En gin e da ta
Maximum output SAE net
Maximum torque SAE net
No . of cy linders
Displacement
Stroke Bore
Compression rat io
Fuel
Dim ensio ns
Length (with licence plate bracket)
Width (across mirrors)
Height (unloaded, incl. roof rails)
T urning circle diameter (curb to curb,
approx.!
Ca pac itie s
F u el t ank
-Total capacity
- Reserve (of total capacity) approx.
Wind shield and headlight * w as her fluid contain er
Engine oil
approx. fi lter change
Controls and equip
ment Safety first
hp@ rpm
lb-ft@ rpm
C ID (cm
3l
in (mm)
in (mm)
200 @ 51 00 -6000
207
@ 1950 -5000
4
121 (1984)
3.65 (92.8) 3.25 (82.5) 10.5: 1
Pr emium unle aded (91 AKI) Recommended for maximum engine performance. Fur
ther
details=> page 267, "Gasoline"
in (mm)
in (mm)
i n ( mm)
ft. (ml
gal/litres
ga l/litres
quarts/I it res
quarts/I it res
180 (4586)
76.3 (1937)
57 .2 (1453)
36.4 (11.1
l
front-wheel drive
18.5 / 70.0
2.1 / 8.0
5.1 / 4.8
4.5 / 4.5
quattro
16.6 / 63.0
•
Vehicle operation Vehicle care Do-it-yourself service Technical data
llffl __ D_ a_ ta ______________________________________________________ _
Applies to vehi cles: with 3 .2 liter 6-c yl. engine
255 hp, 3.2 liter 6-cyl. engine
En gin e data
Maximum output SAE net
Maximum torque SAE net
No. of cylinders
Disp lacement
Stroke
Bore
Compress ion ratio
Fuel
Dim ension s
Length (with licence plate bracket)
Width (across mirrors) Height (un loaded, incl. roof rails)
Turning circle diameter (curb to curb, approx .)
Ca pac ities
Fuel tan k
-Total capacity
-Reserve (of total capacity) approx.
Windshield and headlight* wa sher fluid container
Engine oil
approx. fi lter change hp@rpm
lb-ft@ rpm
CID (cm
3l
in (mm)
in (mm) 255@ 6500
243 @3250
6
190 (3123)
3 .65 (92 .8)
3 .33 (84 .5)
10.1 : 1
P remium unle aded (91 AKI) Recommended for maximum engine performance . Fur
t her
details~ page 267, "Gasoline"
in (mm)
in (mm)
in (mm)
ft . (ml
gal/litres
gal/litres
quarts/litres
quarts/litres 1
80 (4586)
76.3 (1937)
57.2 ( 1453)
36 .4 ( 11 .1 l
front -wheel drive
18.5 / 70 .0
2.1 / 8 .0
5 .1 / 4.8
8 .1 / 8 .1 quattro
16.6 / 63 .0
•
lffl __ C_ o_n_ s_ u_m _ e_ r_ ln_ f_
o _r _m _ a_ t_ i_o _n ______________________________________________ _
For additional road safety information, please visit the Road Safety
website at:
http://www.tc.gc.ca/roadsafety/menu.htm
•
Operating your vehicle outside the U.S.A. or Canada
Government regu lations in the United States and Canada require
that automob iles meet specif ic em ission regulations and safety
standards. Therefore, vehic les bui lt for the U.S.A . and Canada differ
from veh icles sold in ot her countries.
I f you p lan to take your vehic le outside the continental limits of the
Un ited States or Canada, there is the possib ility tha t
• unleaded fue ls for vehicles with cata lytic converter may not be
avai lable;
• fuel may have a considerably lower octane rating. Improper fuel
may cause engine damage;
• service may be inadequate due to lack of proper service faci lities,
t ools or test ing equ ipment;
• replacement parts may not be readily avai lable .
• Navigation syste ms for vehicles bu ilt for the U.S.A . and Canada
wi ll not necessarily work in Europe, and may not work in other coun
tries outside of Nort h America .
0 Note
Audi cann ot be responsible fo r mechan ical damage t hat cou ld
result from inadequate fuel, service or parts avai lab ility. •
Audi Service Repair Manuals and
Literature
Audi Official Factory Service Manuals are published as soon as
possible after model introduction Serv ice manuals are available
from :
Audi Technical Literature Ordering Center Ca ll tol l-free:
Tel. : 1 (800) 544-8021
(from 8:00 AM to 8:00 PM, EST, Monday through Friday)
or access their website www.audi .ddsltd .com on the Internet to
order repair manua ls and ot her Audi literature. •
Maintenance
General
Your vehicle has been des igne d to help keep main tenance requ ire
ments to a minimum. However, a certain amount of regu lar mainte
n ance is st ill necessary to assu re y ou r veh ic le's safety, ec onomy and
reliabi lity. For detai led vehic le maintenance consu lt your Mainte
nance
& Warran ty booklet.
Under difficult operating condition s, for example at extreme ly low
outside temperatures, in very dusty regions, when towing a trailer
very frequently, etc ., some service work sho uld be perfo rme d
between the intervals specified. This applies particu lar ly to :
• oil ch anges, and
• cleaning or replacing the air filter.
_______________________________________________ C
_ o_ n
_ s_u _ m_ e_ r_l_ n _f_o _ r_ m_ a_ t
_ i
_ o _ n
__ lllll
W For the sake of the environm ent
By regularly ma intain ing your vehicle, you help make sure that emis
sion standards are maintained, thus minimizing adve rse effects on
the e nv ironment. •
Important considerations for you and your
vehicle
T he increasing use of elec tronics, sophisticated fue l injection and
emission con trol systems, and t he gene rally increasing tec hn ical
complexity of today's automobiles, have steadily reduced the scope
of maintenance and repai rs which can be carried ou t by vehic le
owners.
Also , safety and environmental concerns p lace very strict
limits on the nature of repairs and adjustments to engine and trans
m iss ion parts whic h an owne r can perform.
Maintenance , adjustments and repairs usua lly require special tools ,
t es ting dev ices a nd othe r eq uipment availab le to s pec ial ly t rai ned
workshop personne l in order to assure proper performance , reli
abil ity and safe ty of the vehicle and its many sy stems .
Im proper maintena nce, adjustments and repairs can impa ir the
operation and reliability of your vehicle and even void your vehicle
wa rranty. T here fore, proof o f servic ing in acc orda nce with the main
tenance schedule may be a condition for upholding a possib le
warranty cla im made with in t he war ran ty per iod .
Above all, operationa l safety can be adversely affected, creating
unnecessary risks for you and your passengers.
I f in doubt about any servicing, have it do ne by your auth orized Audi
dea ler or any other properly equipped and qua lified workshop . We
str ongly u rge y ou to give yo ur auth orized Au di d ealer the oppo rtu
n ity to perform all scheduled maintenance and necessary repairs .
Yo ur dealer has the faci lit ies, origi nal par ts an d trained specia lis ts
to keep your vehic le running proper ly.
Controls and equip ment Safety first
Vehicle operation
Performing limited maintenan ce yourself
The following pages des cribe a li mi ted numbe r of proced ures wh ic h
can be performed on your vehicle with ordinary tools, should the
need a rise a nd trained pers onnel be unavaila ble. Before perfo rm ing
any of these procedures, a lways t horoughly read all o f the app li
cable text and carefu lly fo llow the instructions given. Always rigor
ously observe the
WARNINGS provided.
Before you check anything in the engine compartment , always read
and heed all
WARNINGS ~ & and~ & in "Wo rking i n th e engine
compartment" on
page 273.
& WARNING
• Serious personal injury may occur as a result of improperly
performed maintenance , adjustments or repairs .
• Always be e xtremely careful when working on the veh icle .
Always follow commonly accepted safety practice s and general
common sense . Never risk personal injury .
• Do not attempt any of the maintenance, checks or repairs
described on the following pages if you are not fully familiar with
the se or other procedures with respect to the vehicle , or are uncer
tain how to pro ceed .
• Do not do any work without the proper tools and equipment .
Have the necessary work done by your authorized Audi dealer or
another properly equipped and qualified work shop .
• The engine compartment of any motor vehicle is a potentially
hazardous area . Never reach into the area around or touch the
radiator fan . It is temperature controlled and can switch on
s uddenly -even when the engine is off and the ignition key has
been removed . The radiator fan swit ches on automat ically when
the coolant reaches a certain temperature and will continue to run
until the coolant temperature drops .
• Alway s remove the ignition key before anyone gets under the
vehi cle .
.,_
Vehicle care Do-it-yourself service Technical data
llffl _ __::C:::.::: o:.:.n.:.: s:::.::: u:.:.m .:.:.: e:.: r~ I n:..:.:. f.::
o :.:.r .:.m :.:.:: a:.: t:.:. i.::o :.:.n.:.... _____________________________________________ _
&, W ARNING (continued )
• Always support your vehicle with safety stands if it i s neces
sary to work underneath the vehicle. The jack supplied with the
vehicle is not adequate for this purpose and could collapse
causing serious personal injury .
• If you must work underneath the vehicle with the wheels on
the ground , always make sure the vehicle is on level ground , that
the wheels are always securely blocked and that the engine
cannot be started .
• Always make sure the transmission selector lever (automatic
transmission) is in
" P " (Park position) and the park brake is firmly
applied.
ffi For the sake of the environment
• Changing the engine settings wi ll adverse ly affect emission
l eve ls . T hi s is detri menta l to th e envi ro nm ent and increas es fu el
consumption .
• Always observ e env ironmenta l re gulations w hen disposing of
old e ngine oil, used brake f luid, dirty engine coo lant, spent batteries
or worn out tires .•
Additional accessories,
modifications and parts replacement
Additional accessories and parts
replacement
Alway s co nsult an autho rized Audi de aler before
pu rchasing acc essories .
Your vehicle incorporates t he latest safety d esig n f eatures ensuring
a high standa rd of active and pas sive safety . Th
is saf ety could be compromised by non -approved changes to the
v ehi cle . F or thi s re aso n, if par ts have to be re pla ced , pl ease obs erve
th e fo llow ing points when insta lling add itional acc essories :
A pproved Aud i accesso ries and gen uine Audi pa rts a re avai la bl e
fr om authori zed Aud i dea lers .
Th ese dealers also have the necessary faci lities, tools and tra ined
spec ia li sts to in sta ll th e parts an d acce ssor ies pr op erly .
& WARNING
Using the wrong spare parts or using non -approved accessories
can cause serious personal injury .
• Use only accessories expressly approved by Audi and genuine
Audi spare parts .
• These parts and accessories have been specially designed to
be used on your vehicle .
• Never install accessories such as telephone cradles or
beverage holders on airbag covers or within the airbag deploy
ment zones . Doing so will increase the risk of injury if airbags are
triggered in an accident!
• Before you check anything in the engine compartment , always
read and heed all WARNINGS
=> page 265.
0 Note
• I f item s ot her than ge nuin e Audi s pa re pa rts, add- on eq uipment
and accessory items are us ed or if r epair wor k is not performed
according to s pecified methods, thi s can re sult in severe damage to
your v ehicle's eng ine and body (suc h as c orros io n) a nd advers ely
affect yo ur vehic le 's wa rranty.
• Th e manufacturer cannot be held liable for damage w hich occurs
d ue t o fa ilur e to comply w it h these stipu lation s.•