2007 YAMAHA YBR125 oil type

ALWAYS USE ONLY THE RECOMMENDED GRADE OF ENGINE OIL
1 . Engine oil drain plugc. Remove the drain plug and drain
the oil.
d. Reinstall the drain plug and
tighten it to the specified
torque.Tightening torque:
Drain plug:
14.5 It-lb (2.0 m-kg)
e. Fill engine with oil and install
the dipstick.
Recommended oil:
YAMALUBE 4-stroke motor oil
(20W40 type SG).
Oil quantity:
Total amount:
1.2 L
Periodic oil change:
1.0 L
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
f. Start the engine and warm up
for a few minutes. While
warming up, check for oil leak-
age. If oil leakage is found, stop
the engine immediately and
check for the cause.

1. Air filter case cover
2. Screw(3 Nos)Air filterThe air filter should be cleaned at
the specified intervals. It should be
cleaned more frequently when riding
in unusually wet or dusty areas.
1. Remove panel B. (See page 6-5for removal and installation
procedures.)
2. Remove the air filter case fitting screws and the air filter case
cover.
1. Air filter element
2. Lockable SpringWire
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
3. Remove the air filter from thecase.
4. Unlock the spring wire.
1. Air filter element
2. Frame6. Apply recommended oil to the entire surface of the each element
and squeeze out the excess oil.
They should be wet but not
dripping.
Recommended oil:
20W40 Type SG
2 1
2
1 2
2
1

Drive chain lubricationThe chain consists of many parts
which work with each other. If the
chain is not maintained properly, it
will wear out quickly. Therefore, the
chain must be serviced regularly.
This service is especially necessary
when riding in dusty areas.
1. The drive chain should be
lubricated every 5,000 km.
2. To clean the chain thoroughly,
remove it from the Motorcycle,
dip it in solvent, and clean out as
much dirt as possible. Then, take
the chain out of the solvent to dry
it, and then dip the chain in oil of
20W40. Remove the chain and
hang it on a peg for a while till the
excess oil drips down completely.
Then using a clean cloth wipe the
chain.
Cable inspection and
lubricationDamage to the outer housing of
cables may lead to internal rusting
and interfere with the cable
movement. Replace damaged
cables as soon as possible to
prevent unsafe conditions.
Lubricate the cables with anti-
corrosive oil and cable ends. If a
cable does not operate smoothly,
ask a YAMAHA dealer to replace it.
Recommended lubricant:
20W40 Type SG
Throttle cable and grip
lubricationThe throttle twist grip assembly
should be greased at the time that
the cable is lubricated, since the
grip must be removed to get at the
end of the throttle cable. After
removing the screws, hold the end
of the cable up in the air and put in
several drops of lubricant. With the
throttle grip disassembled, coat the
metal surface of the grip assembly
with a suitable all purpose grease.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
WARNING

8. Clean the seat with a vinyl
upholstery cleaner to keep the
cover pliable and glossy.
9. Automotive-type wax may be
applied to all painted and chrome-
plated surfaces. Avoid
combination cleaner waxes. Many
contain abrasive which may mar
the paint or protective finish. When
finished, start the engine and let it
idle for several minutes.
B. STORAGELong term storage (60 days or more)
of your Motorcycle will require some
preventive procedures to guard
against deterioration. After thor-
oughly cleaning the Motorcycle,
prepare for storage as follows:
1. Drain the fuel tank, fuel lines, and
carburetor float bowl.
2. Remove the empty fuel tank, pour
a cup of SAE 10W30 or 20W40
motor oil in the tank, shake the
tank to coat the inner surfaces
thoroughly and drain off the
excess oil. Reinstall the tank.
3. Remove the spark plug, pour
about one tablespoon of SAE
10W30 or 20W40 motor oil in the
spark plug hole and reinstall the
spark plug. Kick the engine over
several times (with the ignition off)
to coat the cylinder wall with oil.
4. Remove the drive chain.
Thoroughly clean the chain withsolvent and lubricate it. Reinstall
the chain or store it in a plastic bag
(tied to frame for safe-keeping).
5. Lubricate all control cables.
6. Block up the frame to raise both
wheels off the ground.
7. Tie a plastic bag over the
exhaust pipe outlet to prevent
moisture from entering.
8. If storing in a humid or salt-air
atmosphere, coat all exposed
metal surfaces with a light film of
oil. Do not apply oil to any rubber
parts or the seat cover.
9. Remove the battery and charge it.
Store it in a dry place and
recharge it once a month. Do not
store the battery in an excessively
warm or cold place (less than 0ºC
or more than Ambient).
Make any necessary repairs before
storing the Motorcycle.
CLEANING AND STORAGE
7-2
NOTE :

SPECIFICATIONS
8-1
SpecificationsModel LIBERO (5TS8)
Dimensions
Kerb weight :(With Engine Oil &
90% Fuel in Tank)- 119Kg.
Engine ::
Overall length 2,000 mm
Overall width 730 mm
Overall height 1,050 mm
Seat height (Upto Rider) 800 mm
(Upto Pillion Rider) 850 mm
Wheelbase 1,290 mm
Ground clearance 173 mm
Minimum turning radius 2,000 mm
Engine type
Cylinder arrangement
Displacement
Bore x Stroke 49X56
Compression ratio 9 : 1
Starting system
Lubrication system
Maximum power 7.6
Maximum torque 0.80Air cooled 4-stroke,SOHC
Forward inclined single
cylinder
106 cm
mm
Kick starter
Wet sump
PS(5.59 KW) @ 7500
Kgm. @ 6000
3
RPM
RPM
EngineOil:
Capacity
Air filter:
Fuel :
Carburettor:Type:
:
Periodic oil change 1.0
Total amount
Type G
Fuel tank capacity
Reserve amount
Type Variable Venturi Type
Manufacturer M/S Keihin Fie PrivateBe sure to use motor oils that do not contain
antifriction modifiers. Passenger car motor oils (often
labelled Energy conserving) contain anti-friction
additives which will cause clutch and/or starter clutch
slippage, resulting in reduced component life and
poor engine performance.
YAMALUBE 4-Stroke motor
oil (20W40 type SG)
L
1.2 L (First fill/Overhaul)
Wet type element
asoline (Petrol)
13.0 Litres
1.7Litres
Limited India.
CAUTION :

SPECIFICATIONS
8-3
Wheels:
Brakes:
Suspension :
Shock absorberType:
Size:
Front :
Type Drum brake
Operation Right Hand lever
Front Telescopic fork
Rear
:
Front Coil spring/ oil damper
RearFront Spoke wheel
Rear Spoke wheel
Front 1.60 X 18
Rear 1.60 X 18
Rear :
Type Drum brake
Operation Right foot operation
Swing arm
Coil spring/ oil damperWheel travel:
Electrical:
Bulb voltage ,Wattage x Quantity:
Fuse:Front 120 mm
Rear: 90 mm
Ignition system: CDI (Digitally Timing
Generator system:
Type
Standard output 12V
Battery:
Type
Voltage, capacity
Headlight
Tail / Brake light
Front flasher light
Rear flasher light
Meter light
Neutral indicator light
High beam indicator light
Turn indicator light
Tuning Fork Logo 12V 3.4Wx1
MainAdvanced)
Flywheel magneto
Lead acid
12V 2.5AH
(Halogen-HS1) 12V 35W/ 35W x 1
12V 5W/21W x 1
12V10Wx2
12V10Wx2
12V3.4Wx2
12V3.4Wx1
12V3.4Wx1
12V1.7Wx2
1OA

15. Location of Storage and Tool Kit compartments and their use.
16. Procedure of opening and closing of L. H. Side Panel.
17. Battery Maintenance : Checking of electrolyte level (To add only distilled water if required &
to maintain its Specified Level)
18. Correct Drive Chain Slackness (20 ~30 mm).
19. Correct type of Spark Plug and Spark Plug gap.
20. Engine Oil (in Gear Box), level checking and explaining the importance of replacing the Engine
Oil after every 2000 KMS Always use YAMALUBE 4T OIL SG Grade.
21. TFF oil to be replaced after every 10000 Kms.
22. Running- In Period/ Preventive Maintenance Schedule Instructions
23. Information of emission and safety norms (AIS + CATCON).
24. Importance and schedule of Free Services
25. Warranty Terms and Conditions.
INSTALLATION
IMPORTANT CAUTION
10-6
EXPLAINED BYSIGNATURE: _____________ NAME:
CUSTOMER’S SIGN
MAIN SELLING DLR’S STAMP, SIGNATURE
service2.pmd11/3/2006, 8:50 PM 6