2007 YAMAHA RHINO 660 bulb

Cable inspection and lubrication ...... 8-103
Brake pedal and accelerator pedal
lubrication ....................................... 8-105
Rear knuckle upper and lower pivot
lubrication ....................................... 8-105
Steering shaft lubrication .................. 8-107
Wheel removal ................................. 8-107
Wheel installation ............................. 8-109
Battery .............................................. 8-111
Battery maintenance ........................ 8-115
Fuse replacement............................. 8-117
Replacing a headlight bulb ............... 8-123
Headlight beam adjustment.............. 8-129
Tail/brake light bulb replacement ..... 8-131
Troubleshooting................................ 8-137
Troubleshooting charts ..................... 8-139
CLEANING AND STORAGE ................... 9-1
A. Cleaning ........................................... 9-1
B. Storage ............................................ 9-7
SPECIFICATIONS ................................ 10-1
910EE.book Page 3 Friday, October 6, 2006 3:36 PM

8-123 1. Cover at the rear of the headlight
1. Cache au dos du phare
1. Cubierta de la parte posterior del faro
1. Headlight bulb holder cover
1. Cache du porte-ampoule de phare
1. Tapa del portabombillas del faro
EVU01680
Replacing a headlight bulb
If a headlight bulb burns out, replace it as follows.
1. Lift the hood up. (See pages 8-17–8-19 for
hood opening and closing procedures.)
2. Remove the cover at the rear of the headlight
by pulling it off.
3. Remove the headlight bulb holder cover by
pulling it off.
EE.book Page 123 Friday, October 6, 2006 3:36 PM

8-125 1. Headlight bulb holder
1. Porte-ampoule du phare
1. Portabombillas del faro
1. Do not touch the glass part of the bulb.
1. Ne pas toucher le verre de l’ampoule.
1. No tocar la parte de cristal de la bombilla.
4. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.
5. Remove the defective bulb by pulling it out.
WARNING
A headlight bulb is hot when it is on and imme-
diately after it is turned off. Wait for the bulb to
cool before touching or removing it. You can
be burned or a fire could start if the bulb touch-
es something flammable.6. Insert a new headlight bulb into the bulb hold-
er by pushing it in.CAUTION:
Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of the
bulb, and the bulb life will be adversely affect-
ed. Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
EE.book Page 125 Friday, October 6, 2006 3:36 PM

8-127
7. Install the bulb holder by pushing it in and
turning it clockwise.
8. Install the bulb holder cover and the cover at
the rear of the headlight.CAUTION:
Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seated
properly.9. Close the hood.
10. Adjust the headlight beam if necessary.
EE.book Page 127 Friday, October 6, 2006 3:36 PM

8-131 1. Panel A
1. Cache A
1. Panel A
1. Panel B
1. Cache B
1. Panel B
EVU01001
Tail/brake light bulb replacement
If a tail/brake light bulb burns out, replace it as fol-
lows:
1. Remove panel A (if replacing the left tail/
brake bulb) or panel B (if replacing the right
tail/brake bulb) by removing the quick fasten-
er screws and bolts.
EE.book Page 131 Friday, October 6, 2006 3:36 PM

8-133 1. Quick fastener screw (× 8) 2. Bolt (× 2) 3. Panel A
1. Vis à serrage rapide (× 8) 2. Vis (× 2) 3. Cache A
1. Tornillo de fijación rápida (× 8) 2. Perno (× 2) 3. Panel A
1. Tail/brake light bulb holder
1. Porte-ampoule de feu arrière/stop
1. Portabombilla de la luz de freno/piloto trasero
2. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
3. Push the defective bulb in and turn it counter-
clockwise to remove it from the bulb holder.
4. Push a new bulb in and turn it clockwise to in-
stall in the bulb holder.
5. Install the bulb holder (together with the bulb)
by turning it clockwise.
EE.book Page 133 Friday, October 6, 2006 3:36 PM

10-5
Brakes:
System Front and rear unified
Type front Dual disc brake
rear Single disc brake
Operation Foot operation
Suspension:
Front suspension Double wishbone
Rear suspension Double wishbone
Shock absorber:
Front shock absorber Coil spring/gas-oil damper
Rear shock absorber Coil spring/gas-oil damper
Wheel travel:
Front wheel travel 185 mm (7.3 in)
Rear wheel travel 185 mm (7.3 in)
Electrical:
Ignition system DC CDI
Generator system AC magneto
Battery type U1L-11
Battery capacity 12 V 28.0 Ah
Headlight type: Krypton bulbModel YXR66FSEW
EE.book Page 5 Friday, October 6, 2006 3:36 PM

10-6
Bulb voltage, wattage × quantity:
Headlight 12 V 30.0 W/30.0 W × 2
Tail/brake light 12 V 5.0 W/21.0 W × 2
Indicator lights:
Neutral indicator light LED
Reverse indicator light LED
Coolant temperature warning light LED
Parking brake indicator light LED
On-Command four-wheel-drive/differential gear
lock indicatorLCD
High-range indicator light LED
Low-range indicator light LED
On-Command differential gear lock indicator light LED
Specified fuses:
Main fuse 30.0 A
Headlight fuse 15.0 A
Ignition fuse 10.0 A
Auxiliary DC jack fuse 10.0 A
Four-wheel-drive motor fuse 3.0 A
Carburetor warmer fuse 10.0 A
Signaling system fuse 10.0 A
Backup fuse 10.0 AModel YXR66FSEW
EE.book Page 6 Friday, October 6, 2006 3:36 PM