2007 YAMAHA GIGGLE50 brake

6-23
1
2
3
4
5
6
7
8
9
EAU17226
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU24131
Replacing the tail/brake light
bulb1. Remove the tail/brake light lens by
removing the screws.ZAUM00**
1
2
1. Tail/brake light lens
2. Bulb2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
ECA10680
cCDo not overtighten the screws, oth- Tail/brake light bulb, replacing
erwise the lens may break.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
15P-F8199-E0_ch6.pmd2007/06/21, 11:09 23

7-1
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGE
Care
EAU25991
SCOOTER CARE AND STORAGE
EAU26091
CareWhile the open design of a scooter re-
veals the attractiveness of the technol-
ogy, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Fre-
quent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter look-
ing good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a plas-
tic bag after the engine has cooled
down.
2. Make sure that all caps and cov-
ers as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-
ucts onto seals, gaskets and wheelaxles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10781
cC● ●● ●
●
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
● ●● ●
●
Improper cleaning can damage
plastic parts such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc. Use
only a soft, clean cloth or sponge
with mild detergent and water to
clean plastic.
● ●● ●
●
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent orthinner, fuel (gasoline), rust re-
movers or inhibitors, brake fluid,
antifreeze or electrolyte.
● ●● ●
●
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following
areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
● ●● ●
●
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after wash-
ing.
15P-F8199-E0_ch7.pmd2007/06/13, 11:18 1

7-2
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGEAfter nor
mal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
then rinse thoroughly with clean water.
Use a toothbrush or bottlebrush for
hard-to-reach areas. Stubborn dirt and
insects will come off more easily if the
area is covered with a wet cloth for a
few minutes before cleaning.
After r
iding in the r
ain, near the sea or
on salt-spr
ayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.
NOTE:
Salt sprayed on roads in the winter may
remain well into spring.1. Clean the scooter with cold water
and a mild detergent after the en-
gine has cooled down.
ECA10790
cCDo not use warm water since it in-
creases the corrosive action of the
salt.2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated, sur-
faces.
4. Use spray oil as a universal cleaner
to remove any remaining dirt.5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely be-
fore storing or covering it.
EWA10940
w● ●● ●
●
Make sure that there is no oil or
wax on the brakes or tires. If nec-
essary, clean the brake discs
and brake linings with a regular
brake disc cleaner or acetone,
and wash the tires with warm
water and a mild detergent.
● ●● ●
●
Before operating the scooter
test its braking performance and
cornering behavior.
ECA10800
cC● ●● ●
●
Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
● ●● ●
●
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
● ●● ●
●
Avoid using abrasive polishing
compounds as they will wear
15P-F8199-E0_ch7.pmd2007/06/13, 11:18 2

8-2
1
2
3
4
5
6
7
8
9
SPECIFICATIONSTrail
84.0 mm (3.31 in)Front tireType
Tubeless
Size
120/90-10 57J
Manufacturer/model
CHENG SHIN / C-6022Rear tireType
Tubeless
Size
120/90-10 57J
Manufacturer/model
CHENG SHIN / C-6022
Maximum load
177 kg (390 lb)Tire air pressure (measured on cold
tires)Front
175 kPa (25 psi) (1.75 kgf/cm
2) (1.75 bar)
Rear
175 kPa (25 psi) (1.75 kgf/cm2) (1.75 bar)
Front wheelWheel type
Cast wheel
Rim size
10 x 3.00Rear wheelWheel type
Cast wheel
Rim size
10 x 3.00
Front brakeType
Drum brake
Operation
Right hand operationRear brakeType
Drum brake
Operation
Left hand operationFront suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring
Wheel travel
65.0 mm (2.56 in)Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring
Wheel travel
56.0 mm (2.20 in)Electrical systemIgnition system
Transistorized coil ignition
Charging system
AC magnetoBatteryModel
GTX5L-BSVoltage, capacity
12 V, 4.0 Ah
HeadlightBulb type
Halogen bulbBulb voltage, wattage x quantityHeadlight
12 V, 35 W/35.0 W x 1
Tail/brake light
12 V, 5.0 W/21.0 W x 1
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
License plate light (15P3/15P4)
12 V, 5.0 W x 1
Meter lighting
12 V, 1.7 W x 1
High beam indicator light
12 V, 1.7 W x 1
Turn signal indicator light
14 V, 3.0 W x 1
Coolant temperature warning light
12 V, 1.7 W x 1
Engine trouble warning light
12 V, 1.7 W x 1FusesMain fuse
15.0 A
15P-F8199-E0_ch8.pmd2007/07/18, 12:26 2

INDEX
AAcceleration and deceleration ................. 5-2
Air filter element, replacing .................... 6-12BBattery.................................................... 6-20
Brake lever free play, adjusting .............. 6-15
Brake lever, front ...................................... 3-6
Brake lever, rear ....................................... 3-6
Brake levers, lubricating......................... 6-17
Brake shoes, checking ........................... 6-16
Braking..................................................... 5-2CCare .......................................................... 7-1
Catalytic converter ................................... 3-8
Centerstand, checking and lubricating .. 6-18
Coolant................................................... 6-10
Coolant temperature warning light ........... 3-3DDimmer switch.......................................... 3-5EEngine break-in........................................ 5-3
Engine oil................................................. 6-7
Engine trouble warning light .................... 3-3FFinal transmission oil............................... 6-9
Front fork, checking............................... 6-18
Fuel .......................................................... 3-7
Fuel gauge............................................... 3-4
Fuel tank cap........................................... 3-6
Fuse, replacing ...................................... 6-21HHandlebar switches .................................. 3-5
Headlight bulb, replacing....................... 6-22
Helmet holder........................................... 3-9High beam indicator light ......................... 3-3
Horn switch .............................................. 3-5
IIdentification numbers.............................. 9-1
Indicator and warning lights ..................... 3-2KKey identification number ......................... 9-1
Keyhole cover ........................................... 3-2
Kickstarter ................................................ 3-8LLuggage hook.......................................... 3-9MMain switch/steering lock ......................... 3-1
Maintenance, periodic .............................. 6-1
Model label............................................... 9-2PPanels, removing and installing............... 6-5
Parking..................................................... 5-3
Part locations........................................... 2-1
Periodic maintenance and lubrication
chart ....................................................... 6-2
Pre-operation check list ........................... 4-2RRear brake lever free play, adjusting ..... 6-16SSafe-riding points ..................................... 1-4
Safety information .................................... 1-1
Seat.......................................................... 3-9
Spark plug, checking ............................... 6-6
Specifications........................................... 8-1
Speedometer unit..................................... 3-4
Start switch .............................................. 3-5
Starting off ................................................ 5-2
Starting the engine ................................... 5-1Steering, checking ................................. 6-19
Storage ..................................................... 7-3
Storage compartment ............................ 3-10
TTail/brake light bulb, replacing................ 6-23
Throttle cable free play, checking .......... 6-12
Throttle grip and cable, checking and
lubricating............................................ 6-17
Tires ....................................................... 6-13
Troubleshooting...................................... 6-24
Troubleshooting charts ........................... 6-25
Turn signal indicator light......................... 3-3
Turn signal light bulb, replacing............. 6-24
Turn signal switch ..................................... 3-5VValve clearance ...................................... 6-12
Vehicle identification number ................... 9-1WWheel bearings, checking ...................... 6-19
Wheels................................................... 6-15
15P-F8199-E0_ch9ind.pmd2007/06/16, 16:02 3