2007 VOLVO XC70 audio

2007 Volvo XC70
Surround level
This function is used to set the level of the of the rear speakers. To s\
et the level:
- Press SOURCE.
- Turn the SOURCE knob, select ADVANCED MENU and press SOURCE.
- Turn the SOURCE knob, select AUDIO SETTINGS and press SOURCE.
- Turn the SOURCE knob, select SURROUND LEVEL and press SOURCE.
- Turn the SOURCE knob, select the desired level and press SOURCE.
- Press EXIT.
pg. 242 Audio
Audio systems - specifications
HU-650
Output: 4x25 W
Impedance: 4 Ohm
Voltage required: 12 V, negative ground
External amplifier: 4x50 W or 4x75 W
Radio frequency range:
AM: 530 - 1710 kHz
FM: 87.7 - 107.9 MHz
HU-850
Output 1x25 W center speaker
Impedance: 4 Ohm
Voltage required: 12 V, negative ground
External amplifier
1: 4x50 W or 4x75 W
Radio frequency range
AM: 530 - 1710 kHz
FM: 87.7 - 107.9 MHz
1. The HU-850 must be connected to an external amplifier.
Alarm
"Alarm!" is displayed when an alarm message is sent. The function is use\
d to warn the driver of a
serious accident or disaster situation.
file:///K|/ownersdocs/2007/2007_XC70/07xc70_11.htm (18 of 22)12/30/200\
6 5:51:47 PM

2007 Volvo XC70
CAUTION!
The optional supplementary amplifier (HU-850) may be mounted under the\
front passenger's seat. If
the floor of the vehicle has become soaked for any reason, do not turn o\
n the radio. This would cause
damage to the amplifier. Contact a Volvo retailer.
Low battery voltage
If the level of battery voltage is low, a message will be displayed. The\
vehicle's energy conservation
function may switch off the audio system. Recharge the battery by starti\
ng the engine.
pg. 243 Audio
HomeLink® Universal Transceiver (option)
HomeLink® Universal Transceiver
HomeLink® is an advanced system that can be programmed to learn the c\
odes of three different remote
controlled-devices (e.g., garage door openers, remote lighting, entry d\
oor lock). HomeLink®'s sun visor-
mounted transceiver, powered by your vehicle's electrical system, may th\
en be used in place of your
hand-held remote controls.
NOTE: For your security, the HomeLink® Universal Transceiver is designed t\
o not function if you lock
your vehicle from the outside.
Programming the transceiver
- The ignition switch must be turned to the "accessory" position (II) \
before programming the
HomeLink® Universal Transceiver.
file:///K|/ownersdocs/2007/2007_XC70/07xc70_11.htm (19 of 22)12/30/200\
6 5:51:47 PM

2007 Volvo XC70
- Begin by erasing all 3 factory default channels. Hold down the two out\
side buttons (buttons 1 and 3 in
the illustration) on the HomeLink® Universal Transceiver for about 2\
0 seconds, until HomeLink®'s
indicator light begins to flash. Then release the buttons.
- Hold your hand-held transmitter (garage door opener, for example) 2 \
to 5 in. (5 to 12 cm) away from
the HomeLink® surface, keeping the indicator light in view. For place\
ment questions, contact
HomeLink® toll-free 1-800-355-3515 (Internet:
www.HomeLink.com).
- Using two hands, push and hold both your hand-held transmitter's butto\
n and the transceiver button
you wish to program.
The indicator light will flash first slowly, then rapidly. Rapid flashin\
g tells you the HomeLink® button
has been successfully programmed. Release both buttons.
- If you are programming a rolling code-equipped device (e.g., garage d\
oor opener or entry door lock),
refer to "Programming rolling codes" on the next page to complete the pr\
ogramming process.
Repeat the third and fourth steps to program the other two transceiver b\
uttons.
If, after several attempts, you are unable to successfully train the Hom\
eLink® Universal Transceiver to
learn your hand-held transmitter's signal, contact HomeLink® toll-fre\
e 1-800-355-3515 (Internet:
www.
HomeLink.com).
pg. 244 Audio
HomeLink® Universal Transceiver (option)
WARNING!
If you use HomeLink® to open a garage door or gate, be sure no one is\
near the gate or door while it
is in motion.
Do not use the HomeLink® Universal Transceiver with any garage door o\
pener that lacks safety
"stop" and "reverse" features as required by federal safety standards. (\
This includes any garage door
opener model manufactured before April 1, 1982) A garage door opener th\
at cannot "detect" an
object, signalling the door to "stop" and "reverse" does not meet curren\
t federal safety standards.
Using a garage door opener without these features increases the risk of \
serious injury or death. For
more information on this matter, call toll-free 1-800-355-3515 (Interne\
t:
www.HomeLink.com).
NOTE: Canadian residents: During programming, your hand-held transmitter may \
automatically stop
transmitting. To successfully train HomeLink®, continue to hold the H\
omeLink® button. At the same
time, repeatedly press and hold your handheld transmitter's button at tw\
o-second intervals until
HomeLink® has learned your transmitter's code. The HomeLink® indic\
ator light will flash first slowly,
and then rapidly to indicate that the button has been successfully progr\
ammed.
file:///K|/ownersdocs/2007/2007_XC70/07xc70_11.htm (20 of 22)12/30/200\
6 5:51:47 PM

2007 Volvo XC70
Determining if your garage door uses a rolling code
Determine, in one of the following ways, if your garage door uses a roll\
ing code system and is
manufactured after 1996:
l Refer to the garage door opener owner's manual for verification.
l If your hand-held transmitter appears to program the HomeLink® Univer\
sal Transceiver but the
programmed button does not activate the garage door, your garage door op\
ener may have a rolling code.
l Press the programmed HomeLink® button. If the garage door opener has \
the rolling code feature, the
HomeLink® indicator light flashes rapidly and then glows steadily aft\
er approximately 2 seconds.
To train a rolling code garage door opener, follow these instructions after programming the desired
transceiver button according to "Programming the transceiver." The help \
of a second person may make
training easier.
- Locate the training button on the garage door opener motor head unit. \
The location and color of the
training button may vary. If you encounter difficulty, refer to the gara\
ge door opener owner's manual or
call toll-free 1-800-355-3515 (Internet:
www.HomeLink.com).
- Press the "training" button on the garage door opener motor head unit \
until the "training" light comes
on.
- Press and release the programmed HomeLink® button. Press and releas\
e the programmed HomeLink®
button a second time to complete the training process.
Some garage door openers may require you to do this procedure a third ti\
me to complete the training.
The programmed button on your HomeLink® Universal Transceiver should \
now operate your garage
door opener. The original handheld transmitter can also be used, as desi\
red, to operate the garage door.
The remaining two HomeLink® buttons can be programmed in the same way\
. In the event of any
problems in programming the HomeLink® Universal Transceiver, call tol\
l-free 1-800-355-3515
(Internet:
www.HomeLink.com).
pg. 245 Audio
HomeLink® Universal Transceiver (option)
Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used in p\
lace of your hand-held
transmitters.
To operate, the key must be turned to the "accessory" position (II) or\
the engine must be running. Press
the programmed HomeLink® button to activate the garage door, driveway\
gate, security lighting, home
security system, etc.
Your original hand-held transmitters may, of course, be used at any time\
.
Erasing programmed buttons
file:///K|/ownersdocs/2007/2007_XC70/07xc70_11.htm (21 of 22)12/30/200\
6 5:51:47 PM

2007 Volvo XC70
Individual buttons cannot be erased. To erase all three programmed butto\
ns:
- Turn the ignition key to the "accessory" position (II).
- Hold down the two outside buttons on the HomeLink® Universal Transc\
eiver for about 20 seconds,
until HomeLink®'s indicator light begins to flash.
- Release both buttons.
The HomeLink® buttons can be reprogrammed using the procedures descri\
bed on the previous page.
Reprogramming a single HomeLink® button
- Press and hold the desired HomeLink® button. Do not release the button until step 3 has been
completed.
- When the indicator light begins to flash slowly (after approximately \
20 seconds), position your hand-
held transmitter 2 to 5 in. (5 to 12 cm) away from the HomeLink® su\
rface.
- Press and hold the hand-held transmitter button. The HomeLink® indi\
cator light will flash first slowly,
then rapidly. When the indicator light flashes rapidly, release both but\
tons.
The previously programmed device has now been erased and the new device \
can be activated by
pressing the HomeLink® button that has just been programmed. This pro\
cedure will not affect any other
programmed HomeLink® buttons.
NOTE:
l Retain the original transmitter(s) for future programming procedures (\
e.g., if you purchase a new
vehicle).
l For your own security, erase all programmed buttons on the HomeLink® \
Universal Transceiver when
you sell your vehicle.
l Metallic sun protection films should not be used on any windows in a veh\
icle equipped with
HomeLink® Universal Transceiver. This could interfere with the transc\
eiver's function.
pg. 246 Audio
This page left intentionally blank.



Contents | Top of Page
file:///K|/ownersdocs/2007/2007_XC70/07xc70_11.htm (22 of 22)12/30/200\
6 5:51:47 PM

2007 Volvo XC70
2 0 0 7
VOLVO XC70
Index

pg. 247-250 Index
A
A/C (air conditioning)
77-82
ABS
2, 49, 137
Accessory installation (special warnings)
6
Active Bi-Xenon headlights (ABL)
55
Air conditioning
77-82
Air distribution
75, 78
Air quality sensor
79
Air vents
75
Alarm
116
All Wheel Drive
134
All Wheel Drive -towing
143
Anti-lock Brake System (ABS)
2, 49
Audio system
226
AUTO (climate control)
77
Automatic transmission
130
Automatic transmission - kickdown
131
Automatic transmission - Sport mode
133
Average speed
61
AWD
134
B
Battery
187, 195
replacing
197
file:///K|/ownersdocs/2007/2007_XC70/07xc70_12.htm (1 of 9)12/30/2006 \
5:51:48 PM