2007 TOYOTA CAMRY HYBRID display

’07Camry hybrid_U (L/O 0610)
237
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
To dial by Number1. Push the talk switch and say “Dial by Number”.
“Dial by number. Please push the talk
switch and say the number.” is heard and
“Dial by Num” is displayed. 2. Push talk switch and say “XXXX”.
“Push the off −hook switch to dial. Other-
wise, push the talk switch and say dial,
go back, or delete.” is heard.
To dial the number, do the one of the
following:
Push the off −hook switch.
Push the talk switch and say “Dial”.
Turn the “AUDIO CTRL” knob until
“Dial” is displayed and push the knob.
If the number exceeds 24 digits, the sys-
tem may not function properly.
INFORMATION
The system can recognize single
digits from zero to nine, # (pound),
∗ (star) and + (plus). Numbers that
are ten or greater are not recog-
nized.
To speed up input, it is a good idea
to group all digits into a continuous
string. However, you can enter each
digit individually or group digits to-
gether in preferred string lengths.
The display corresponding to each op-
eration appears on the screen as fol-
lows:
Input operation—
You say: “Nine, nine, five”
Voice output: “995 push the offhook
switch to dial. Otherwise, push the
talk switch and say dial, go back, or
delete.”
Display: “995”
You say: “Seven, three, four”
Voice output: “734 push the offhook
switch to dial. Otherwise, push the
talk switch and say dial, go back, or
delete.”
Display: “995734”
Repeat the above procedure until the
entire number that you want to dial is
input.
Go back operation—
You say: “Go back”
Voice output: “Go back, the last num-
bers entered have been removed.
Push the talk switch and continue
adding numbers otherwise say dial,
go back, or delete.”
Display: “995”
Repeating the above operation deletes
the last digits in reverse order of in-
put.
Delete operation—
You say: “Delete”
Voice output: “Deleted. The entire
number to dial has been deleted.
Please push the talk switch and say
the number.”
Display: “Dial by Num”
The display will return to the initial
screen that allows a number to be
input.

’07Camry hybrid_U (L/O 0610)
238
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Cancel operation—
Do either one of the following:
Push the onhook switch at anytime
during the operation.
Push the talk switch and say “Can-
cel” after the beep at anytime dur-
ing the operation except while a call
is connected.
When receiving a phone call, a ring tone
is audible and the system changes into
the telephone mode.
When receiving a phone call, the display
is as follows. The display differs depend-
ing on whether or not the vehicle is in
motion.
When the vehicle is stopped:
Number, name or “Incoming” is displayed.
When the vehicle is in motion:
“Incoming” is displayed.
Do either one of the following:
Pushing the off−hook switch allows you
to talk on the phone.
Pushing the on −hook switch refuses
the call.
To adjust the ring volume, push “+” or “ −”
on the steering volume controls. Volume
adjustment cannot be done using the au-
dio system.
Repeatedly pushing “ −” on the steering
volume controls mutes the ring.
When receiving an international phone
call, the name of the party may not be
displayed correctly depending on the cellu-
lar phone. To transfer a call to the phone:
The received call can be transferred from
the hands
−free system to the cellular
phone that is connected to Bluetooth . For
details, refer to the user’s guide for the
cellular phone.
—Receiving a p hone call

’07Camry hybrid_U (L/O 0610)
239
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
While talking on the phone, the display is
as follows. The display differs depending
on whether or not the vehicle is in motion.
When the vehicle is stopped:
Number is displayed.
When the vehicle is in motion:
“Talking” is displayed.
When the call is finished, push the on−
hook switch.
In the following situations, your voice may
not reach the party.
Talk alternately with the other party on
the phone. If you talk at the same
time, the voice may not reach each
other. (It is not a malfunction.)
Keep the volume of receiving voice
down. Otherwise, echo is coming up.
When you talk on the phone, speak
clearly towards the microphone.
When driving on a rough road.
When driving at high speeds.
When the window is open.
When the air conditioning vents face
the microphone.
When the sound of the air conditioning
fan is loud. To transfer a call from the phone:
Pushing the off
−hook switch while talking
on the cellular phone that is connected to
Bluetooth  allows you to talk hands −free.
To transfer a call to the phone:
The call can be transferred from the
hands −free system to the phone that is
connected to Bluetooth . For details, refer
to the user ’s guide for the cellular phone.
—Talking on the phone

’07Camry hybrid_U (L/O 0610)
245
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
NOTICE
Do not insert anything into the driv-
er’s side vent, attach anything to it,
or use sprays around the driver ’s side
vent. These things may cause the sys-
tem not to work properly.
∗: This system adopts the plasmacluster
technology, manufactured under license
from SHARP Corporation. “Plasmacluster
TM”
is a trademark of SHARP Corporation.
“ECO HEAT/COOL” switch
Push the “ECO HEAT/COOL” switch to
select the “ECO HEAT/COOL” (economi-
cal) mode of the air conditioning. The indi-
cator on the switch comes on and “ECO”
appears on the air conditioning display to
indicate that the mode is on.
The efficiency of the air conditioning is
limited because the consumption of elec-
tricity is reduced, achieving a reduction of
fuel consumption. As a result, it may take
longer than the usual amount of time for
the inside air temperature to reach the set
temperature. The “ECO HEAT/COOL” mode is canceled
in the following cases:
The temperature control is set at “LO”
(the lowest temperature) or “HI” (the
highest temperature).
The air flow is set in the floor/wind-
shield mode or windshield mode.
“ECO HEAT/COOL” switch is pushed
again.

’07Camry hybrid_U (L/O 0610)
255
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
1. Push the “INFO” button to displaythe “Information” screen.2. Touch the “Trip information” on thescreen.
Trip information appears on the screen.
When the instrument panel lights are
turned on, the brightness of the screen
will be reduced.
You can adjust the brightness of the
screen. To adjust the brightness, see the
“Navigation System Owner ’s Manual” for
the procedure.
CAUTION
Do not operate the screen while the
vehicle is moving. Be sure to operate
the screen only when the vehicle is
stopped.
Trip information
(with navigation system)

’07Camry hybrid_U (L/O 0610)
256
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Consumption screen
1. Transition of fuel consumption in thepast 30 minutes
2. Regenerated energy in the past 30 minutes
3. Best fuel economy among average
4. Cruising range
5. Average fuel consumption The information listed above is dis-
played when you touch the “Consump-
tion” switch on the “Energy Monitor”
screen.
The displayed values on the screen indi-
cate general driving conditions. Accuracy
varies with driving habits and road condi-
tions.
When the “POWER” switch is set at ON,
the last previously used mode displayed
just before the “POWER” switch is turned
off will appear.
If “Reset All” is touched, all of the graph-
ics and values except the cruising range
will be reset.
If the electrical power source is discon-
nected from the navigation system screen,
the screen will automatically be set to the
initial mode.
1. Fuel consumption in the past 30 minutes
(“Consumption”)
The transition of fuel consumption in
the past 30 minutes is displayed in the
graph. 2. Regenerated energy in the past 30
minutes
The regenerated energy in the past 30
minutes is indicated with symbols.
One symbol indicates 50 Wh. Up to 4
symbols will be shown. The energy of 50
Wh illuminates a 50 W bulb for an hour.
3. Best fuel economy (lowest fuel con- sumption) among average
(“Best”)
Best fuel economy among average is
displayed.
If the average fuel consumption is reset
by touching the “Reset” and the average
fuel consumption is the lowest, the value
is overwritten. 4. Cruising range (“Cruising Range”)
The distance the vehicle can travel with
the remaining fuel is calculated and
displayed based on the quantity of re-
maining fuel and past fuel consumption.
The cruising range display indicates the
approximate distance that you can drive
until the fuel gauge reaches “E”. It is
different from the actual distance traveled.
If the fuel gauge malfunctions, the mileage
figure will not appear.

’07Camry hybrid_U (L/O 0610)
257
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
When the vehicle is refueled, the driving
range is recalculated.
The actual driving range varies with driv-
ing habits and road conditions. If fuel con-
sumption is good, the driving range will be
longer than indicated. If fuel consumption
is poor, the driving range will be shorter
than indicated.
If the low fuel level warning light comes
on, refuel the vehicle even if the display
indicates that the vehicle can be driven
further.5. Average fuel consumption (“Average”)
Average fuel consumption is displayed
based on total driving distance and to-
tal fuel consumption.
The calculation is reset by touching the
“Reset”. If the average fuel consumption
is the lowest, the value of the best fuel
economy among average is overwritten.
Energy Monitor screen
Touching the “Energy” switch turns on
the “Energy Monitor” that displays the
hybrid system operating condition.
The arrow on the screen indicates the
movement of the energy. See “Energy
monitor” on page 3 for the representative
screen.
The segments of the battery on the
screen indicate the status of the hybrid
battery. See “—Hybrid battery status” on
page 5 for details.
To reset the hour: Push the “H” button.
To reset the minutes: Push the “M” button.
The “POWER” switch must be set at ACC
or ON.
If the electrical power source has been
disconnected from the clock, the time dis-
play will automatically be set to 1:00 (one
o’clock).
When the instrument panel lights are
turned on, the brightness of the time indi-
cator will be reduced.
Clock

’07Camry hybrid_U (L/O 0610)
258
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
The direction is indicated on the inside
rear view mirror.
If the “POWER” switch was turned off with
the system on, the system will automati-
cally turn back on when the “POWER”
switch is turned on.
Push the “AUTO” switch for longer than 3
seconds to turn the compass system on
and off.
The compass indicates the direction
that the vehicle is heading. In the
above case, it shows that the vehicle is
heading north.Displays
Directions
N
NE E
SE
S
SW W
NWNorth
Northeast East
Southeast
South
Southwest West
Northwest
The compass may not show the correct
direction in the following conditions:
The vehicle is stopped immediately af-
ter turning.
The compass does not adjust while the
vehicle is stopped.
The “POWER” switch is turned off im-
mediately after turning.
The vehicle is on an inclined surface.
The vehicle is in a place where the
earth’s magnetic field is subject to in-
terference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).
The vehicle is magnetized. (There is a
magnet or a metal object on or near
the inside rear view mirror.)
The 12 volt battery has been discon-
nected.
If your vehicle is out of the set zone,
refer to “CALIBRATING THE COMPASS”
below to set the zone number.
If the deviation is small, the compass
works to calibrate the direction automati-
cally while the vehicle is in motion.
For additional precision or for complete
calibrating, see “CALIBRATING THE
COMPASS” below.
Compass