2007 SKODA SUPERB radio

Audio
20
•RDS evaluation is not possible if the signal is too weak. In this case it
is the frequncy which appears in the status bar or in the info field instead
of the RDS station name.
•If there are unfavourable reception conditions (e.g. in the mountains)
the unit checks very often the alternative frequencies. This can cause brief
mutings.
•If this causes mutings and tone distortions in extremely poor reception
locations, the RDS function is temporarily switched off.
Traffic radio reception
Many stations in the FM range regularly transmit the current traffic reports
within their transmitting range.
After selecting a station, check if the set station has traffic reports.
If the set station is a TP station (station with traffic radio reception), the
identification “ TP” appears in addition to the station name in the info field
of the radio basic menu. The station remains set. The functions “ traffic
information standby ” and “EON” are active.
If the set station has no traffic radio station or cannot be received, the unit
searches automatically for another traffic radio station in the reception
area (start station finding). The message “ TP SEEK” (searching traffic
radio station) appears in the radio information display.
Listening to traffic information
A traffic information is detected by the unit using the traffic information
identification. Even if the radio is set very low or in the CD mode you can
listen to a traffic information. The play function is performed in Mono. The
message “ Info” appears in the radio information display. Simultaneously
the traffic information is recorded in the traffic information memory (TIM)
⇒ page 20. Interrupting a traffic information
If a traffic information was interrupted, press the button . A new
traffic information can be emitted.
Cancel traffic information standby
The traffic information standby is cancelled in the menu “
Select source”
when switching over to FM or AM level.
Traffic information memory - Traffic Memo (TIM)
The radio navigation system has a digital voice memory with which upto
nine traffic reports with a total duration of maximum four minutes can be
automatically recorded.
If the radio is switched on each traffic report of the set station is
recorded, if the show “ TP” is present in the info field.
If the unit is switched off traffic reports are recorded for as long as they
were selected in the menu “ Audio Settings” under “TIM-Standby”
⇒ page 14. This function can also be switched off.
Replaying the traffic reports
If you press the button , the replay of the traffic reports starts with
the last recorded traffic information and continues to the oldest traffic infor-
mation. The show “ TIM Track 4 Time 14:10 TP ” appears in the info field:
TIM - Play function of a recorded traffic information
Tra ck 4 - There are four traffic information. The play function begins with
the latest information.
Time 14:10 - Recording time
TP - TP station
TIMA1
TIMA1
20.book Page 20 Tuesday, December 6, 2005 2:26 PM

Audio21
Replaying the random traffic report
The traffic reports can also be replayed in the random order.
•replaying older traffic report - press the rocker button on the left for
two seconds.
•replaying latest traffic report - press the rocker button on the right
for two seconds.
Fast replay of the traffic reports
If the rocker button on the right is held pressed, the reports are quickly
replayed with time details ( 3 - 5 times faster).
Repeating the traffic report
A traffic report is repeated, if the rocker button on the left is pressed
again (last pressing was carried out more than two seconds ago).
Ending TIM function
The function is ended by pressing again the button and the radio
basic menu is called up.
Erasing the traffic reports
The traffic reports are automatically erased six seconds after ending the
memory standby, which is 24 hours.
Note
•Select a radio station before switching off the unit, otherwise no traffic
reports can be stored.
•The storing can be activated for 24 hours or until the next switching on
by pressing the button if the unit is switched off. In the process
and if it is necessary a radio station is automatically set.
•The oldest announcement will be overwritten if the traffic information
memory is full.
•The beginning is overwritten, if a report lasts more than four minutes.
A signal tone sounds as information that the entire report could not be
stored.
•If a traffic report is stored when the unit is switched on, this action
continues until the end. Then the last selected setting is effective.
•If no traffic reports were stored, the message “ No Messages” appears
in the radio information display after pressing the button and a
signal tone sounds.
CD mode
Switching over to CD mode
– Call up the menu “ Select source ” ⇒fig. 11 with the button
.
– Mark and confirm the menu field “ CD”. The CD changer
checks the magazine; thus the message “ Check Magazine”
appears.
A2
A2
A2
A2
TIMA1
TIMA1
TIMA1
Fig. 11 Menu - Select
source
AUDIOA15
20.book Page 21 Tuesday, December 6, 2005 2:26 PM

Audio
22
– Afterwards the play function starts in the order of the CDs inserted in the magazine.
Interrupting the CD play function
The play function of a CD is interrupted in the event of a traffic information.
At the same time the identification “ Info” is indicated in the info field of the
CD menu.
End CD play function
The CD play function is ended when selecting another tone source in the
menu “ Select source ”. The unit changes to radio mode.
Note
•If no music CD is inserted or when driving in difficult regions ⇒page 23
the error message “ CD ERROR” or “CD1 ERROR ” appears in the info
field.
•The selected CD with the current track (“ Tr a c k”) is displayed in the CD
information display. The menu fields besides the station buttons indi-
cate the assignment of the magazine with CDs.
•The message “ CD1 Track1 Play ” appears in the status bar if the
navigation is active.
CD functions
Select CD
– Select the desired CD using the corresponding station button . Select track
– Press the rocker button to se
lect the track. If the rocker
button on the right is pressed, the play function of the following
track starts. The current track starts from the beginning by
pressing the rocker button on the left. Press the rocker button
on the left briefly in succession, in order to reach the previous
track.
Scan
– Press the button for a brief playing of the tracks (ten seconds) of one CD. Press this button once again in order to
abort this function.
Playing track in random sequence
– Press the button in order to play the track of a CD in the random sequence. Press this button once again in order
to abort this function.
CD MIX
– This function makes it possible to play in the random sequence not only the track of a CD but also the CDs inserted
in the CD changer. For this step mark and confirm the menu
field “ CD Shuffle ” in the menu “ Audio Settings ”. Switch back
and forth between the options “ Disc” and “ Magazine ” by
pressing the menu knob .
A12
1
A12
A2
SCANA14
CD MIXA11
A18
20.book Page 22 Tuesday, December 6, 2005 2:26 PM

Navigation
48
Delete a destination from the destination memory
You can remove the destinations which are no longer needed
from the alphabetical destination memory and the Top 10
memory. First of all call up the respective memory from the desti-
nation memory menu. Then the entry to be deleted is selected in
the memory. In order to prevent a destination being deleted inad-
vertently, a confimation is asked for.
– Mark and confirm the menu field “ Delete destinations”.
– Mark and confirm in the destination memory menu the menu field “ Edit Top 10 ”. A sub-menu is called up
– Mark and confirm the menu field “ Delete Top 10” in the sub-
menu. The Top 10 memory is called up.
– Mark and confirm the entry to be deleted in the respective destination memory list.
– Confirm the menu field “ Delete destination”, in order to
delete the entry from the alphabetical destination memory.
The destination memory list is called up again. If required
other destinations can be deleted. Menu field “ Abort” - aborts
the deletion process and calls up again the destination
memory list.
– Confirm the menu field “ Delete from Top 10”. The destination
is deleted from the Top 10 memory and the menu “ Edit Top
10 ” is called up. Menu field “ Delete all” - also deletes the
destination from the alphabetical destination memory. NoteIf the destination to be deleted is also entered in the TOP 10 memory, the
message “
N.B. Top 10 destination ” appears in the menu bar. When
confirming the menu field “ Del. Destination” the destination is also
removed from the Top 10 memory.
Automatic tailback function (for units
with dynamic navigation)
Important information
The unit is prepared technically for dynamic navigation. For the availability
of this function, the following requirements apply:
•Navigation CD must assist the dynamic navigation
•at least one TMC station must be receiveable
Please do not hesitate to contact your Škoda Service Partner should you
have any further questions regarding this matter.
What is dynamic navigation?
The dynamic navigation enables an automatic adaptation of the calcu-
lated route on the basis of the receiveable traffic reports.
The traffic reports are not audibly emitted by different broadcasting
stations in addition to the radio program via a TMC (Traffic Message
Channel).
The navigation system receives this data via a separate TMC box and
evaluates it. If a traffic report is received, which is of great importance for
the calculated route, the route is automatically recalculated.
20.book Page 48 Tuesday, December 6, 2005 2:26 PM

Navigation49
The traffic reports are shown in the map display by means of symbols:
• slow-moving traffic
• traffic jam
• closed road
The corresponding stretch of the journey is shown in the map display by
a dotted line.
So that you can use the dynamic navigation, a radio station must be able
to receive the traffic reports emitted via TMC. The TMC box selects auto-
matically a TMC station; you can also manually select another station.
Note
The proper functioning of the automatic route influence depends on
the transmitted traffic reports. The radio stations broadcasting the
traffic reports are responsible for its content.
Select TMC station
– Press the button tailback function . The tailback menu appears.
– Mark and confirm the menu field “ RDS station” ⇒ fig. 41 . A list
with the available TMC stations appears.
– Mark and confirm the desired station ⇒fig. 42 .
An aerial symbol in the symbol and map display indicates that a
TMC Station can be received.
Note
The audible station is not changed as a result of this. If the selected station
cannot be received, automatically the next TMC to be received is set.
Fig. 41 Select TMC
station
Fig. 42 TMC station
A16

20.book Page 49 Tuesday, December 6, 2005 2:26 PM

Navigation
54
Anti-theft coding
Description
Each time when:
•the unit is disconnected from the power supply of the vehicle
•the battery is disconnected
•the electrical fuse for the radio was blown
The information “ SAFE” appears in the display after switching on the unit.
Then the unit can only be operated again by entering the correct code.
Caution
•This code number is affixed together with the serial number behind the
instructions on the “ Unit map”.
•The “unit map ” must absolutely be disconnected and safe - never
store in the vehicle.
Enter code - Cancel electronic lock
The electronical lock is cancelled by entering the correct code.
The order of the operating steps must be maintained:
– Switch on the system. After t he start screen with the Škoda
logo appears the menu for entering the code with the informa-
tion “ Please enter your numerical code. ” ⇒ fig. 46.
– Enter the numerical code by marking the corresponding digits in the digit register one after the other using the menu knob
and confim each digit by pressing the menu knob . The
digits are entered into four lower numerical fields.
– Mark and confirm the field “ OK” with the menu knob .
The unit is again ready for operation!
Fig. 46 Enter safety code
A18
A18
A18
20.book Page 54 Tuesday, December 6, 2005 2:26 PM

Index
60
Memory
Destination . . . . . . . . . . . . . . . . . . . . . . . 45
Destination- . . . . . . . . . . . . . . . . . . . . 33, 45
Top 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Traffic information . . . . . . . . . . . . . . . . . . 20
Menu for editing . . . . . . . . . . . . . . . . . . . . . . . . 26
Moving -Operating . . . . . . . . . . . . . . . . . . . . . 9
Music braodcasting . . . . . . . . . . . . . . . . . . . . 14
N
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Basic menu . . . . . . . . . . . . . . . . . . . . . . . 24
dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Navigation CD . . . . . . . . . . . . . . . . . . . . . . . . . 9
R
Radio station Playing . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Retrieve . . . . . . . . . . . . . . . . . . . . . . . . . . 18
radio stations . . . . . . . . . . . . . . . . . . . . . . . . 17
RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Read out Destination . . . . . . . . . . . . . . . . . . . . . . . 34
Regional programs . . . . . . . . . . . . . . . . . . . . 14
Register ASF . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacement service . . . . . . . . . . . . . . . . . . . 8 Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Alternative . . . . . . . . . . . . . . . . . . . . . . . . 51
calculate . . . . . . . . . . . . . . . . . . . . . . . . . 40
S
Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37, 43
SelectFunctions . . . . . . . . . . . . . . . . . . . . . . . . . 37
Selection Last destination . . . . . . . . . . . . . . . . . . . . 27
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16
Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 find . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
TMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Station finding automatic . . . . . . . . . . . . . . . . . . . . . . . . . 17
station finding manual . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Store Flagged destination . . . . . . . . . . . . . . . . . 35
Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Destination in the destination memory . . 33
Street . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . 12, 40
System with DSP . . . . . . . . . . . . . . . . . . . . . . . . . 16
without DSP . . . . . . . . . . . . . . . . . . . . . . . 15
T
Tailback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Tailback funcion . . . . . . . . . . . . . . . . . . . . . . 48
Television . . . . . . . . . . . . . . . . . . . . . . . . . . . 56switch on . . . . . . . . . . . . . . . . . . . . . . . . . 56
Tone Source . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Town . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Town centre . . . . . . . . . . . . . . . . . . . . . . . 29
Town centre . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Traffic information . . . . . . . . . . . . . . . 20, 21, 50
Traffic information memory . . . . . . . . . . . . . . 20
Traffic radio information . . . . . . . . . . . . . . . . . 20
Traffic report . . . . . . . . . . . . . . . . 20, 21, 48, 50
Traffic report memory . . . . . . . . . . . . . . . . . . 14
TV Operation . . . . . . . . . . . . . . . . . . . . . . . . . 57
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Station finding . . . . . . . . . . . . . . . . . . . . . 56
TV standard . . . . . . . . . . . . . . . . . . . . . . . . . . 58
TV Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
V
Vehicle position current . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Flagged destination . . . . . . . . . . . . . . . . . 34
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Video text . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Volume . . . . . . . . . . . . . . . . . . . . . . . 14, 15, 16
20.book Page 60 Tuesday, December 6, 2005 2:26 PM

Unit name
Radio navigation system DX
Please affi x serial no. and code no.
Code
no.
Serial no. Unit
name
Information
The unit map must be discon-
nected and safe - never store in the
vehicle.
If the unit map with the code num-
ber may get lost, please contact
your Škoda
Service Partner or importer.
There one will be glad to assist you
without any cost.
DX-průkaz.indd 16.12.2005 14:21:15