2007 SKODA OCTAVIA Owner's Manual

Automatic gearbox DSG
136
Tiptronic
The Tiptronic allows the driver to also shift gears manually.
Switching over to manual shifting
– Push the selector lever to the right out of position D. As soon as the
gearbox has switched over, 6 5 4 3 2 1 appears in the display, with the
gear engaged being highlighted ⇒fig. 147 .
Shifting up gears
– One-touch forward of the selector lever (in the Tiptronic position)
⇒ fig. 146 . Shifting down gears
– One-touch back of the selector lever (in the Tiptronic position) .
It is possible to switch over to manual both when the car is stationary and also when
driving.
When you accelerate, the gearbox shifts up
automatically in gears 1, 2, 3, 4 and 5
into the next higher gear just before the maximum permissible engine speed is
reached.
If you select a lower gear, the automatic gearbox does not shift down until there is
no risk of the engine overrevving. (Does not apply for the shifting from 2nd to 1st
gear.)
If you operate the kickdown function, the ge arbox shifts into a lower gear in line
with the vehicle speed and engine speed.
Emergency programme
An emergency programme exists in the event of a fault in the system.
The gearbox operates in a corresponding emergency programme if there are func-
tional faults in the gearbox electronics. This is indicated by all of the segments in the
display lighting up or going out.
A functional fault can have the following effect:
•The gearbox only shifts into certain gears.
•The reverse gear R cannot be used.
•The manual shift programme (Tiptronic) is switched off in the emergency mode.
If the gearbox has switched over to emergency mode, drive to the nearest
specialist garage in order to have the fault rectified.
Fig. 146 Selector lever:
Manual shifting of gears
Fig. 147 Information
display: Manual shifting
of gears
A+
A-
NKO A5 20 MR08.book Page 136 Wednesday, April 11, 2007 2:54 PM

Automatic gearbox DSG137
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Selector lever-emergency unlocking (DSG)
In case of interruption of the power supply (e.g. flat vehicle battery, defec-
tive fuse) or defect of the selector lever lock, the selector lever can no
longer be shifted from the position P in the normal way and the vehicle
can no longer be moved. The selector lever must be unlocked in case of
emergency.
– Apply the handbrake firmly.
– Open the stowage compartment in front centre console* or the front ashtray.
– Carefully pull up the front left and right cover.
– Pull up rear cover.
– Press with a narrow object (e.g. ignition key) the yellow plastic hoop -arrow- to the left.
– Simultaneously press the shiftlock butt on in the handle of the selector
lever in the position N
8).
Tow-starting and towing vehicle
Tow-starting a vehicle
It is not possible to tow-start vehi cles fitted with automatic gearbox ⇒page 239.
you can use jump-start cables connected to the battery of another vehicle for
starting your car if the vehicle battery is flat ⇒page 238.
Towing a vehicle
Please pay attention to the following information if it comes necessary to tow-in
your car ⇒page 239.
8)If the selector lever is moved again into the position P, it is once again blocked.
Fig. 148 Selector lever-
emergency unlocking
NKO A5 20 MR08.book Page 137 Wednesday, April 11, 2007 2:54 PM

Communication
138
Communication
Multifunction steering wheel*
Operating the radio system
The driver can set the basic functions of the radio system by simply operating the
buttons on the steering wheel so that he can concentrate on the traffic situation
without being distracted as little as possible by operating the radio system
⇒ fig. 149 .
This applies only if your radio equipment has been installed at the factory. You can
of course operate the radio system at the appliance. You will find a description in
the operating instructions of your radio system.
If the headlights are switched on, the bu ttons on the steering wheel come on when
pressing the button
.
By pressing the buttons, you can carry out the following functions: The buttons apply for the respective operating mode of the current radio system.
Note
The loudspeakers in the vehicle are
matched to a power output of 30 W.
Fig. 149 Multifunction
steering wheel: Buttons
for the operation of the
radio
ButtonRadioCassetteCD
Button for stored
transmitter
forward

without functionTitle search forward

Increase volume 
Decrease volume 
Button for stored
transmitter back

without functionTitle search back

Lighting of buttons 
Frequency search back
Fa s t re w i n d Reading the
previous CD

Frequency search for- ward
Fa s t fo r w a rd Reading the
following CD

Mute switch 
A1
A2
A3
A4
A5
A6
A7
A8
NKO A5 20 MR08.book Page 138 Wednesday, April 11, 2007 2:54 PM

Communication139
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Radio and mobile phone operation
The driver can set the basic functions of the radio and mobile phone system by
simply operating the buttons on the steering wheel so that he can concentrate on
the traffic situation without being distracted as little as possible by operating the
radio and mobile phone system ⇒fig. 150 .
This applies only if your radio and mobi le phone equipment has been installed at
the factory. You can of course operate the radio and mobile system at the appliance.
You will find a description in the operating instructions of your radio system.
If the headlights are switched on, the buttons on the steering wheel come on when
pressing the button
.
By pressing the buttons, you can carry out the following functions:
The buttons apply for the respective operating mode of the current radio system.
Fig. 150 Multifunction
steering wheel: Buttons
for the radio and mobile
phone operation
ButtonRadioCassetteCDPhone
Button for stored
transmitter forward
without
functionTitle search
forward

Press briefly: Scroll through the phonebook for individual names
Press for a long time: Scroll through the phonebook for letters 
Increase volume 
Decrease volume 
Button for stored
transmitter back
without
functionTitle search
back

Press briefly: Scroll through the phonebook for individual names
Press for a long time: Scroll through the phonebook for letters 
Lighting of buttons 
without functionReject, end a call, reach one level higher in the menu 
Call up menu telephone Receive, accept a call, confirm menu selection 
without functionActivation/deactivation button for voice control 
(button PTT)
A1
A2
A3
A4
A5
A6
A7
A8
NKO A5 20 MR08.book Page 139 Wednesday, April 11, 2007 2:54 PM

Communication
140
Note
The operation of the mobile phone fitted wi th multifunction steering wheel is only
possible on certain models of mobile phone. More detailed information is available
from your Škoda Service Partner.
Universal telephone preinstallation with voice
control*
Description
The voice control is activated according to equipment installed on the vehicle by
pressing the button PTT (push to talk)  on the adapter ⇒fig. 151 or the button  on the multifunction steering wheel ⇒page 139, fig. 150 .
A phone phonebook is part of the mobile phone preinstallation with voice control.
In the phone phonebook there are 1500 free memory locations available. This
phone phonebook is independent of the ap pliance used for the mobile telephone.
Fo r v e h i c l e s f i t t e d w i t h m u l t ifunction steering wheel, the operation is performed via
the function buttons on the steering wheel ⇒page 139.
Furthermore the volume can be changed indi vidually at any time with the button
for setting the radio or on vehicles fitted with multifunction steering wheel* with
function buttons on the steering wheel. If the system answers with the voice response “
Telephone is not ready”, please
check the operating state of the telephone as follows:
•Is the telephone switched on?
•Is the PIN code entered?
Dialogue
The period, in which the telephone system is ready to receive voice commands and
carry out the voice commands, is called DIALOGUE. The system gives audible feed-
back and guides you if necessary through the relevant functions. You can start or
end the dialogue at any time by pressi ng the PTT button. You can also end the
dialogue with the voice command CANCEL.
The dialogue is always automatically ended after carrying out an operation, e.g.
after erasing the name from the phonebook.
The dialogue of the incoming call is i mmediately interrupted and you can accept
the call by pressing the button
.
If a voice command is not detected, the system answers with “ Sorry?” and a new
entry can be performed. After the 3rd error the answer “ Cancel” is given and the
dialogue is ended.
Optimum understanding of the voice commands depends on the following
factors:
•Speak with a normal tone of voice wi thout intonation and excessive voice
pauses.
•Avoid insufficient articulation.
•Close the doors, windows and sliding roof, in order to reduce or stop disturbing
exterior noise.
•It is recommended to speak louder at higher speeds, so that the tone of your
voice is louder than the increased surrounding noise.
•During the dialogue avoid additional nois e in the vehicle, e.g. simultaneously
talking occupants.
•Do not speak, if the system makes an announcement.
•The microphone for voice control is directed to the driver and front passenger.
Therefore the driver and the front passenger can operate the equipment.
Fig. 151 Button for
switching on the voice
control
NKO A5 20 MR08.book Page 140 Wednesday, April 11, 2007 2:54 PM

Communication141
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
Pay attention primarily to the traffic situation! As the driver you are fully
responsible for the traffic safety. Use the telephone system only to such an
extent, so that you are in full control of your vehicle at any time.
Caution
Taking the mobile phone out of the adapter during the call can lead to interruption
of the connection. When taking out the mobile phone, the connection to the
factory-fitted antenna is interrupted, this reduces the quality of the transmitting
and receiving signal. This might result additionally in harmful radiation from the
mobile phone in the interior of the ve hicle and the charging of the telephone
battery is interrupted.
Note
•Please also refer to the additional instructions ⇒page 149, “Mobile phones
and two-way radio systems”.
•Please contact your Škoda Service Partner if there are any points which are not
clear.
•The voice control of the telephone is only possible for adapters with PTT button.
Suitable adapters are available at a Škoda Service Partner.
Inserting the mobile phone and adapter
Only one telephone mount is factory-fitted. An adapter for the mobile
phone can be purchased from Škoda original accessories.
Inserting the mobile phone and adapter
– First of all push the adapter in the direction of arrow ⇒fig. 152 up
to the stop into the mount. Press the adapter slightly downwards, until
it locks securely into position.
– Insert the mobile phone into the adapter (as specified in manufac- turer's instructions).
Removing the mobile phone and adapter
– Press simultaneouly the side locks of the mount and remove the mobile phone and adapter ⇒fig. 152 .
This enables you to make full use of the advantages of a normal carphone (“hands-
free system” using a microphone integrated in the vehicle, optimal transmission of
signals using an external aerial etc.). The battery of the mobile phone is also
constantly charged.
Fig. 152 Universal prep-
aration for the mobile
phone
AA
AA
NKO A5 20 MR08.book Page 141 Wednesday, April 11, 2007 2:54 PM

Communication
142
Mobile phone operation
If you select the menu Phone in the information display and the phone is not in the
adapter, Insert phone is shown on the display.
After inserting the phone in the adapter, the system begins to load the phone book
from the phone and the SIM card into the information display.
When inserting the mobile phone the next ti me only perform an update of the rele-
vant phone book. The updating takes a few minutes, first of all the last read phone-
book appears on the information displa y. Newly stored telephone numbers are
only shown after the updating has ended.
The telephone numbers are loaded from the mobile phone depending on the
memory date, beginning with the oldest entry. If the number of telephone numbers
exceed 1 500, the newly stored telephone numbers are not loaded from the mobile
phone. If several telephon e numbers in the phonebook are under one name, all the
telephone numbers with the same name are loaded separately.
If a telephone event (e.g. incoming or outg oing call, dialogue of the voice control)
occurs during the updating procedure, the updating is interrupted. After the tele-
phone event has ended, the updating starts anew. The following is shown one after the other on the display:
Please wait
Loading... last calls xxx
Loading... last calls xxx
Loading... missed calls xxx
Loading... phone book xxx
During the reading, the number of read telephone numbers is displayed in the
information display.
After loading is completed, phone book, last calls, accepted calls and missed calls
appear in the display.
Using the system•You can scroll through the telephone me mory for individual names or menus
by briefly pressing the rocker switch ⇒fig. 153 .
•You can scroll for letters alphabetically within the telephone memory by
pressing the rocker switch at the bottom for a lengthy period.
•You can return to the main menu of th e information display by pressing the
rocker switch at the top for a lengthy period.
•The selected menu is displayed by briefly pressing the button .
Overview of the possible functions and read outs:
Fig. 153 Information
display: Control
elements
ActivityRead out in display
Selected call numberCalling... Name Number
accepted call
incoming call... Name
or
incoming call... Number
or
incoming call...
Accept
Refuse
Call terminatedTe r m i n a t e d
AA
AA
AA
AB
NKO A5 20 MR08.book Page 142 Wednesday, April 11, 2007 2:54 PM

Communication143
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
You can operate the mobile phone via the voice control
⇒page 140 or via the
buttons of the multifunction steering wheel ⇒page 139.
Voice commands
Voice commands for mobile phone operation Voice commands for operating the phone phone book
Other possible commands
Number
engagedLine Busy
No service foundNo Service
Enter PIN codeEnter PIN
Voice commandActivity
ENTER PIN/PIN CODEAfter this command the PIN code of the mobile
phone can be entered ⇒page 144.
DIAL NUMBERAfter this command a telephone number can be
entered which establishes a connection to the
requested partner ⇒page 144.
REDIALAfter this command the last selected telephone
number is selected again ⇒page 145.
ActivityRead out in display
Voice commandActivity
SAVE/STORE
NAMES/NAME/NUMB ERAfter this command a name with its telephone
number can be stored in the phone phone book
⇒page 145.
SELECT NAMES/NAMEAfter this command a telephone number which
was stored under its given name in the phone
phone book can be selected ⇒ page 146.
DELETE NAMES/NAMEAfter this command a name in the phone phone
book can be erased ⇒page 146.
LISTEN TO/PLAY
PHONEBOOKAfter this command you ca n listen-in to the phone
phone book ⇒page 146.
DELETE PHONEBOOKAfter this command the complete phone book or a
name can be erased ⇒page 147.
Voice commandActivity
DIALThe telephone number is selected.
STOREThe name and the telephone number are stored in
the phone phonebook or the entered PIN code is
stored.
REPEATThe entered name or the digits are repeated. Then
the system requests with voice response “ please
proceed ” the entry of further digits or commands.
NKO A5 20 MR08.book Page 143 Wednesday, April 11, 2007 2:54 PM