2007 Seat Ibiza 5D maintenance

If and when215
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Fuses on left side of dash panelFuses
Number Consumer Amperes
1 Secondary water pump 1.8 20 VT (T16) 15
2A BS/E S P 10
3 Vacant
4 Brake light, clutch switch, relay coils 5
5 Engine control unit (petrol) 5
6 Right side light 5
7 Left side light 5
8 Mirror heating unit 5
9 Lambda probe 10
10 Signal“S”
a). Radio unit 5
11 Electric mirror power supply 5
12 Headlamp height adjustment 5
13 Oil pressure/level sensor 5
14 Additional heating engine/fuel pump 10
15 Automatic gearbox unit 10
16 Heated seats 15
17 Engine control unit 5
18 Instrument panel /Heating and ventilation, Navigation, Headlamp height adjustment, Electric mirror 10
19 Reversing light 10
20 Windscreen washer pump 10
21 Main beam headlight, right 10
IBI_ANG_0707 Seite 215 Montag, 6. August 2007 3:59 15

If and when217
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Fuses below steering wheel in relay holderPTC fuses46
Windscreen wiper unit 20
47 Heated rear window unit 20
48 Indicator unit 15
49 Cigarette lighter 15
50 Locking unit 15
51 Radio/CD/GPS/Telephone 20
52 Horn 20
53 Dipped headlight (left side) 15
54 Right rear window control 25a)The signal “S”is a system which includes the starter and steering lock and enables, after the ignition is switched off and with out removing the key from the steering and starter lock,
certain electrical components to be switched on, including for example, the radio, the courtesy light, etc. This function is de activated on removing the key from the steering and starter
lock.
Number Consumer Amperes
1 PTCs (Supplementary electrical heating using air) 40
2 PTCs (Supplementary electrical heating using air) 40
3 PTCs (Supplementary electrical heating using air) 40
Number
Consumer Amperes
IBI_ANG_0707 Seite 217 Montag, 6. August 2007 3:59 15

If and when219
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Some of the electrical items listed in
the table are only fitted on certain
models or are optional extras.
Please note that the above list, while correct at the time of printing, is subject
to alterations.
Bulb changeGeneral notesBefore changing any bulb, first turn off the equipment concerned.
Do not touch the bulb glass. Fingerprints vaporise in the heat, causing a
reduction in the bulb life and condensation on the mirror surface, thus
reducing efficiency.
A bulb should only be replaced by one of the same type. The type is inscribed
on the bulb, either on the glass part or on the base.
It is highly recommended to keep a box of spare bulbs in the vehicle. At the
very least, the bulbs that most affect road safety should have spares in the
vehicle. Rear lights on frame
Brake/position 12V/P21/5W
Turn signals 12V/P21W
Rear lights on tailgate
small position light 12V/W5W
antifog lamp 12V/P21W
reverse lamp 12V/P21W
Single reflector headlamps*
full beam/dipped beam 12V 60/55W (H4)
turn indicator 12V/PY 21W
position lamp 12/W5W
Double reflector headlamps
dipped beam 12V/55W (H7)
roadway 12V/55W (H3)
turn signals 12V/PY21W
position lights 12V/W5W
10
Cable control unit 5
11 Clima fan 5
12 Vacant
13 Jatco unit for automatic gearbox 5
14 Vacant
15 Vacant
16 Vacant
Number
Consumer Amperes
IBI_ANG_0707 Seite 219 Montag, 6. August 2007 3:59 15

If and when221
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side lights
Indicator lights
Dipped headlight lamp
– Raise the bonnet.
– Remove the loops
⇒fig. 150 outwards in the direction of the
arrow and remove the cover.
– Remove the lamp cable connector ⇒fig. 151.
– Undo the retainer spring and remove.
– Remove the lamp and fit the new lamp in the same position, making sure it sits correctly.
– Press the retaining spring on the lamp base and clip on.
– Plug in the connector.
– Fit the plastic cover and replace the loops ⇒fig. 150 .
– Check the headlight adjustment.
ACAD
Fig. 150 Dipped head-
light lamp
Fig. 151 Dipped head-
light lamp
A2
AA
A2
IBI_ANG_0707 Seite 221 Montag, 6. August 2007 3:59 15

If and when223
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side beam lights–Raise the bonnet. – Remove the loops
⇒fig. 154 in the direction of the arrow and
remove the cover.
– Pull on the cables to release the lamp holder from the casing ⇒fig. 155.
– Pull on the lamp and replace.
– To assemble proceed in reverse order.
– Fit the plastic cover and secure the loop.
Fig. 154 Side lightsFig. 155 Side lights
A1
AC
IBI_ANG_0707 Seite 223 Montag, 6. August 2007 3:59 15

If and when225
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Fog lights– Remove the grille, taking out the bolt ⇒fig. 158 , carefully
pull the grille on the side of the screw and release the cover. – Undo the two fastening bolts
⇒fig. 158 and when released
unplug the connector.
– Release the headlight cover.
– Unplug the lamp cable.
– Undo the lamp retainer spring and remove.
– Remove the lamp and fit the new lamp in the same position, making sure it sits correctly.
– Press the retaining spring on the lamp base and clip on.
–Plug in the lamp cable.
–The assembly of the cover and the headlamp is carried out in
reverse order.
Fig. 158 Fog lightsFig. 159 Fog lights
AA
AF
IBI_ANG_0707 Seite 225 Montag, 6. August 2007 3:59 15

If and when227
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
– Remove the plastic cover ⇒page 226, fig. 161 and the
plastic caps ⇒page 226, fig. 161 carefully levering with the
flat part of a screwdriver and ta king special care not to scratch
the paintwork.
– Extract the bolts ⇒page 226, fig. 162 and disconnect the
connector.
– Remove the rear light from its housing.Rear light on tailgate: Accessing the rear light
Side light 1/ Fog light/ reverse light
– Unscrew the bolts ⇒fig. 164 and take the lamp holder out.
– Press and rotate the large lamp holder to the left. For the small lamp, rotate and extract the lamp holder and pull on the lamp.
– Remove lamp and replace.
– Fit the lamp holder and fit.
– Fit the caps and the plastic cover ⇒fig. 163 .
NoteEnsure that all of the joints, sealing components and the plastic caps are
correctly fitted.
AA
AB
AC
Fig. 163 Rear light on
tailgate
Fig. 164 Access to the
lamp
AD
AB
AA
AB
IBI_ANG_0707 Seite 227 Montag, 6. August 2007 3:59 15

If and when229
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Interior light and front reading light To r e m o v e g l a s s
– Insert a fine screwdriver between the casing and the glass
⇒fig. 167 .
– Carefully remove the glass, levering it to avoid possible damage.
To replace the lamps
– Pull the lamps outwards.
– To remove the central lamp, hold and press to one side.
Assembly
– Proceed in the reverse order, pressing gently on the outer edge of the side light. – First fit the glass with the fast
ening tabs over the frame of the
switch. Next press the front part until the two long tabs click on
the support.
Additional brake lights*Given the difficulty involved in the replac ement of this light it should be done
by the Technical Service.Glovebox light*– Insert screwdriver above, between the light and the glove box.
– Carefully remove the light Next lift the light out sideways.
– Replace the bulb.
– Insert the light on the connector side, first underneath then push at the top until it clicks into place.
Fig. 167 Front reading
light
IBI_ANG_0707 Seite 229 Montag, 6. August 2007 3:59 15