2007 SATURN VUE HYBRID tow

To adjust for compass variance do the following:
1. Find your current location and variance
zone number on the following zone map.
2. Press and hold the on/off button until a zone
number appears in the display. The compass
is now in zone mode.3. Keep pressing the on/off button until the
desired zone number appears in the display.
Release the button. After approximately
four seconds of inactivity, the new zone
number will be locked in and the comp/temp
display will return.
Cleaning the Mirror
When cleaning the mirror, use a paper towel or
similar material dampened with glass cleaner.
Do not spray glass cleaner directly on the mirror
as that may cause the liquid cleaner to enter
the mirror housing.
129
ProCarManuals.com

Your vehicle must have a working electrical
system (including adequate battery power) for the
OnStar
®equipment to operate. There are other
problems OnStar®cannot control that may prevent
OnStar®from providing OnStar®service to you
at any particular time or place. Some examples are
damage to important parts of your vehicle in an
accident, hills, tall buildings, tunnels, weather
or wireless phone network congestion.
Your Responsibility
You may need to increase the volume of your
radio to hear the OnStar®advisor. If the light next
to the OnStar®buttons is red, this means that
your system is not functioning properly and should
be checked by a dealer. If the light appears
clear (no light is appearing), your OnStar
®
subscription has expired. You can always press
the OnStar®button to conrm that your OnStar®
equipment is active.
Storage Areas
Glove Box
To open the glove box, pull the lever to the left.
Cupholder(s)
Your vehicle has a removable cupholder liner and
cupholder located inside the center console
storage area. To access, pull the cover towards
the rear of the vehicle. To remove the liner, pull it
out of the cupholder. To replace, push the liner
back in. To remove the cupholder, push the tab in
near the passenger’s seat and pull straight up.
To replace, slide the two tabs at the rear of
the cupholder into the slots at the rear of the
center console and push the cupholder gently into
place. There is additional storage underneath
the cupholders. There are two more cupholders
located at rear of the center console. Push the
button to access.
134
ProCarManuals.com

Floor Console Storage Area
Your vehicle may have a oor console storage
area. Push the button to open.
Center Console Storage Area
Your vehicle has a center console storage area.
To access, slide the cover back towards the rear of
the vehicle. It is equipped with two accessory
power outlets. One is located inside the storage
area and another hidden under the cupholders.
There is a hole in the storage area for a cellphone
wire to be routed through.
Garment Hooks
Your vehicle has four garment hooks. They are
located in the rear of the vehicle.
Cargo Area
Your vehicle has a cargo area organizer, which is
located in the rear of the vehicle. This storage
space is designed to hold small items and includes
integrated storage bins.
Use the following procedure to access and
assemble the rear cargo organizer.
1. Pull up on the latch of the rear panel lid of the
cargo organizer to open it.
2. Lift the front of the cargo organizer and fold
out the end panels.
135
ProCarManuals.com

3. Turn the end panels forward and snap them
into the rear panel lid.
4. Pull the center divider out from the rear
panel lid.5. Turn the center divider rearward and snap it
into the panel lid.
6. Reverse the above steps to stow the dividers
and close the cargo organizer.
Push rmly on the rear panel lid to engage
the latch of the organizer.
136
ProCarManuals.com

Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high or high beam to low, pull the turn signal lever
all the way towards you. Then release it.
When the high beams
are on, this light on the
instrument panel
cluster will also be on.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you that
you want to pass.
To ash the high beams from low beam, pull the
turn signal/multifunction lever all the way
towards you. Then release it.
Windshield Wipers
Be sure to clear ice and snow from the wiper
blades before using them. If the wiper blades are
frozen to the windshield, gently loosen or thaw
them. If the blades do become damaged, install
new blades or blade inserts. SeeWindshield Wiper
Blade Replacement on page 338.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools
down. Clear away snow or ice to prevent an
overload.
United States
146
ProCarManuals.com

The lever on the right side of the steering column
operates the windshield wipers. Push up or
pull down on the lever to place it in one of the
following positions.
MIST or
8(Mist):Pull the lever down and
release it for a single wiping cycle. The lever will
return to its original position. For more cycles, hold
the lever down before releasing it.
OFF or
9(Off):Move the lever to this position
to turn off the wipers.
INT or
&(Intermittent):Move the lever to this
position to set a delay between wipes. To set
for a shorter or longer delay between wipes,turn the band with the arrow pointing to the
numbers (1, 2, or 3). Select 3 for the most frequent
movement; select 1 for the least frequent.
LO or
OO(Low):Move the lever to this position
for slow, steady wiping cycles.
HI or
OOOO(High):Move the lever to this
position for rapid wiping cycles.
Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
Pull the windshield wiper lever toward you to
operate the windshield wipers. Washer uid will
squirt onto the windshield and the wipers will
run for a few cycles to clear the windshield.
For more wash cycles, pull the lever toward you
and hold it there.
Canada
147
ProCarManuals.com

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part is not working, the other
part can still work and stop you. For good
braking, though, you need both parts working well.
If the brake system warning light comes on,
there is a brake problem. Have your brake system
inspected right away.
The brake light is located in the instrument panel
cluster.
This light should come on briey when you turn
the ignition key to RUN. If it does not come
on then, have it xed so it will be ready to warn
you if there is a problem.
When the ignition is on, the brake light will come on
when you set your parking brake. The light will
stay on if your parking brake does not release fully.A chime will also sound if the parking brake is not
fully released and the vehicle is moving. If it stays
on after your parking brake is fully released,
it means you have a brake problem.
The brake light will also come on to indicate a low
brake uid level. SeeBrakes on page 318for
more information.
If the light comes on while you are driving, pull off
the road and stop carefully. You may notice that the
pedal is harder to push or the pedal may go closer
to the oor. It may take longer to stop. If the light
is still on, have the vehicle towed for service.
SeeTowing Your Vehicle on page 270.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light
is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
United StatesCanada
169
ProCarManuals.com

Anti-Lock Brake System
Warning Light
The Anti-Lock Brake System (ABS) warning light
will come on briey, as a check, when you
start your vehicle. If it does not, have your vehicle
serviced so that the light works properly when
it needs to.
If the light stays on after
you start your engine, or
comes on and stays
on while you are driving,
try resetting the system.
To reset the system, do the following:
1. If you are driving, pull over when it is safe
to do so.
2. Be sure the vehicle is in PARK (P).
3. Turn off the ignition.
4. Then restart the engine.If the light remains on after resetting the system or
comes on again while driving, your vehicle
needs service. If the ABS light is on, but the
regular brake system warning light is not on, the
anti-lock brakes are not working properly, but
the regular brakes are still functioning. Have your
vehicle serviced right away. If both brake lights
are on, you do not have anti-lock brakes, and there
is a problem with your regular brakes as well.
Have your vehicle towed for service. SeeTowing
Your Vehicle on page 270.
The ABS warning light should come on briey
when you turn the ignition key to RUN. If the light
does not come on then, have it xed so it will
be ready to warn you if there is a problem.
170
ProCarManuals.com