2007 SATURN OUTLOOK tow

Power Steering Fluid
The power steering uid
reservoir is located
toward the front of the
engine compartment
on the passenger’s side
of the vehicle. See
Engine Compartment
Overview on page 386
for reservoir location.
When to Check Power Steering Fluid
It is not necessary to regularly check power
steering uid unless you suspect there is a leak in
the system or you hear an unusual noise. A
uid loss in this system could indicate a problem.
Have the system inspected and repaired.
How to Check Power Steering Fluid
To check the power steering uid, do the following:
1. Turn the key off and let the engine
compartment cool down.
2. Wipe the cap and the top of the reservoir clean.
3. Unscrew the cap and wipe the dipstick with a
clean rag.
4. Replace the cap and completely tighten it.
5. Remove the cap again and look at the
uid level on the dipstick.
The uid level should be somewhere within the
cross-hatched area on the dipstick. If the uid is at
the ADD mark, you should add uid.
What to Use
To determine what kind of uid to use, see
Recommended Fluids and Lubricants on page 497.
Always use the proper uid.
Notice:Use of the incorrect uid may damage
your vehicle and the damages may not be
covered by your warranty. Always use the
correct uid listed in Recommended Fluids and
LubricantsRecommended Fluids and
Lubricants on page 497.
408
ProCarManuals.com

When rotating your tires, always use the correct
rotation pattern shown here.
Do not include the compact spare tire in your tire
rotation.
After the tires have been rotated, adjust the front
and rear ination pressures as shown on the
Tire and Loading Information label.
Make certain that all wheel nuts are properly
tightened. See “Wheel Nut Torque” under
Capacities and Specifications on page 483.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt
off. SeeChanging a Flat Tire on page 447.
439
ProCarManuals.com

If a Tire Goes Flat
It is unusual for a tire to blowout while you are
driving, especially if you maintain your vehicle’s
tires properly. If air goes out of a tire, it is
much more likely to leak out slowly. But if you
should ever have a blowout, here are a few tips
about what to expect and what to do:
If a front tire fails, the at tire creates a drag that
pulls the vehicle toward that side. Take your
foot off the accelerator pedal and grip the steering
wheel rmly. Steer to maintain lane position,
and then gently brake to a stop well out of the
traffic lane.
A rear blowout, particularly on a curve, acts much
like a skid and may require the same correction
you would use in a skid. In any rear blowout
remove your foot from the accelerator pedal. Get
the vehicle under control by steering the way
you want the vehicle to go. It may be very bumpy
and noisy, but you can still steer. Gently brake
to a stop, well off the road if possible.{CAUTION:
Lifting a vehicle and getting under it to
do maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
If a tire goes at, the next part shows how to use the
jacking equipment to change a at tire safely.
446
ProCarManuals.com

Removing the Spare Tire and Tools
The tools needed to remove the spare tire are
located in the storage compartment on the driver
side, at the rear of the vehicle.
1. Open the jack storage compartment by
squeezing down on the latch tab and
pulling the cover off.
A. Tool Bag
B. Wing Bolt
C. Jack2. Remove the wing bolt (B) by turning it
counterclockwise
3. Push the jack (C) up out of the holding
bracket.
4. Turn the jack on its side, with the bottom
facing toward you.
5. Pull the jack straight out, bottom rst.
The tools you will be using include the jack (A)
and lug wrench (B).
448
ProCarManuals.com

{CAUTION:
Rust or dirt on the wheel, or on the parts
to which it is fastened, can make the
wheel nuts become loose after time. The
wheel could come off and cause an
accident. When changing a wheel, remove
any rust or dirt from the places where the
wheel attaches to the vehicle. In an
emergency, a cloth or a paper towel can
be used to do this; but be sure to use a
scraper or wire brush later, if needed, to
get all the rust or dirt off.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a
serious accident.10. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces, and spare
wheel.
11. Install the compact spare tire.
12. Lower the vehicle by attaching the lug wrench
to the jack and turning the wrench
counterclockwise. Lower the jack completely.
454
ProCarManuals.com

Secondary Latch System
Your vehicle has an underbody mounted tire hoist
assembly equipped with a secondary latch
system. It is designed to stop the compact spare
tire from suddenly falling off your vehicle if the
cable holding the spare tire is damaged. For the
secondary latch to work, the tire must be
stowed with the valve stem pointing down. See
Storing a Flat or Spare Tire and Tools on page 459
for instructions on storing the spare tire correctly.
{CAUTION:
Before beginning this procedure read all
the instructions. Failure to read and follow
the instructions could damage the hoist
assembly and you and others could get
hurt. Read and follow the instructions
listed next.To release the spare tire from the secondary latch,
do the following:
{CAUTION:
Someone standing too close during the
procedure could be injured by the jack. If
the spare tire does not slide off the jack
completely, make sure no one is behind
you or on either side of you as you pull
the jack out from the under spare.
1. If the cable is not visible, start this procedure
at Step 3.
456
ProCarManuals.com

4. Slide the cable retainer through the center of
the wheel and start to raise the compact
spare tire.
Make sure the retainer is fully seated across
the underside of the wheel.
5. When the compact spare tire is almost in the
stored position, turn the tire so the valve is
toward the rear of the vehicle.
This position helps when checking the air
pressure in the compact spare tire.
6. Raise the tire fully against the underside of
the vehicle. Continue turning the lug wrench
until you feel more than two clicks. This
indicates that the compact spare tire is secure
and the cable is tight. The spare tire hoist
cannot be overtightened.
7. Make sure the tire is stored securely. Push,
pull (A), and then try to turn (B) the tire. If the
tire moves, use the lug wrench to tighten
the cable.
460
ProCarManuals.com

Storing the Flat Tire
Notice:Storing the full-size at tire in the
underbody hoist system can expose it to heat
from the exhaust system. This can damage
the tire and underbody hoist system. Do
not store the full-size at tire in the underbody
hoist system.
1. Remove the cable package from the jack
storage area.
2. Remove the small center cap by tapping the
back of the cap with the extension of the
shaft, if the vehicle has aluminum wheels.
3. Put the at tire in the rear storage area with
the valve stem pointing toward the rear of the
vehicle.4. Hook on end of the cable onto the outside
portion of the liftgate hinge opposite (B).
5. Pull the cable (A) through the door striker (E),
the center of the wheel (D), and the plastic
spare tire heat shield (C), as shown.
461
ProCarManuals.com