2007 PONTIAC G6 Owners Manual

Playing a Specic Loaded CD
For every CD loaded, a number appears on the
display. To play a specic CD, press the numbered
pushbutton that corresponds to the CD you
want to play. A small bar appears under the CD
number that is playing, and the track number
appear on the display.
If an error appears on the display, see “CD
Messages” later in this section.
s(Reverse):Press and hold this button to
reverse quickly within a track. You will hear sound
at a reduced volume. Release this button to
play the passage. T#, the elapsed time, and REV
displays.
\(Fast Forward):Press and hold this button to
advance quickly within a track. You will hear
sound at a reduced volume. Release the button to
play the passage. T#, the elapsed time, and
FWD displays.
RPT (Repeat):With repeat, one track or an entire
CD can be repeated.To use repeat, do the following:
To repeat the track you are listening to, press
and release the RPT button. REPEAT ON
and RPT displays. Press RPT again to turn off
repeat play. REPEAT OFF displays and
RPT disappears from the display.
To repeat the CD you are listening to, press
and hold the RPT button for more than
two seconds. REPEAT ON and RPT displays.
Press RPT again to turn off repeat play.
REPEAT OFF displays and RPT disappears
from the display.
RDM (Random):With random, you can listen to
the tracks in random, rather than sequential,
order, on one CD or on all of the CDs.
To use random, do one of the following:
To play the tracks on the CD you are listening
to in random order, press the RDM button.
RANDOM TRACKS and RDM displays. Press
RDM again to turn off random play. RANDOM
OFF displays and RDM disappears from
the display.
241

To play the tracks on all of the CDs that are
loaded, in random order, press and hold the
RDM button for more than two seconds.
A beep sounds, RANDOM ALL CDS, and
RDM displays. Press RDM again to turn
off random play. RANDOM OFF displays and
RDM disappears from the display.
xSEEKw:Press the down arrow to go to the
start of the current track, if more than eight seconds
have played. Press the up arrow to go to the
beginning of the next track. If either arrow is held or
pressed more than once, the player continues
moving backward or forward through the CD.
To scan the current CD, press and hold either
SEEK arrow for more than two seconds. The CD
goes to the next track, plays the rst 10 seconds,
then goes to the next track. Press either SEEK
arrow again to stop scanning.
To scan all of the CDs loaded, press and hold either
SEEK arrow for more than four seconds. The CD
goes to the next CD, plays the rst 10 seconds of
the rst track, then goes to the next CD. Press
either SEEK arrow again to stop scanning.DISP (Display):Press this knob to switch
between time, temperature, and the elapsed time
of the track. To change the default on the
display (CD#/Track#/Time,
CD#/Track#/Temperature, or Track#/Elapsed
Time/Temperature), press the knob until you see
the desired display, then hold the knob for
two seconds. The radio produces one beep and
the selected display is now the default.
AUTO TONE/AUTO EQ (Automatic
Equalization):Press this button to select the
desired equalization setting while playing a
CD. The equalization is set whenever a CD is
played. For more information, see “AUTO TONE”
or “AUTO EQ” listed previously in this section.
BAND:Press this button to listen to the
radio when a CD is playing. The inactive CD(s)
remains safely inside the radio for future listening.
SRCE (Source):Press this button to play a
CD or to access the remote device, when listening
to the radio.
242

Using Song List /RMode
The six-disc CD changer has a feature called
song list. This feature is capable of saving 20 track
selections.
To save tracks into the song list feature, perform
the following steps:
1. Turn the radio on and load it with at least
one CD. See “LOAD” listed previously in
this section for more information.
2. Check to see that the CD changer is not in
song list mode. S-LIST should not appear in
the display. If S-LIST is present, press
the SONG LIST button to turn it off.
3. Select the desired CD by pressing the
numbered pushbutton and then use the SEEK
left arrow to locate the track to be saved.
The track begins to play.4. Press and hold the song list button for two or
more seconds to save the track into memory.
When song list is pressed, one beep
sounds. After two seconds of pressing song
list continuously, two beeps sound to
conrm that the track has been saved and
TRACK number ADDED displays.
5. Repeat Steps 3 and 4 for saving other
selections.
SONG LIST FULL displays if you try to save more
than 20 selections.
To play the song list, press the song list button.
One beep sounds and SONG LIST displays.
The recorded tracks begins to play in the order
that they were saved.
Seek through the song list by using the SEEK
arrows. Seeking past the last saved track returns
you to the rst saved track.
243

To delete tracks from the song list, perform the
following steps:
1. Turn the CD player on.
2. Press the song list button to turn song list on.
SONG LIST displays.
3. Press the SEEK arrows to select the desired
track to be deleted.
4. Press and hold the song list button for
two seconds. When song list is pressed,
one beep sounds. After two seconds of
continuously pressing the song list button,
two beeps sound to conrm that the track has
been deleted and TRACK number DELETED
displays.
After a track has been deleted, the remaining
tracks are moved up the list. When another track
is added to the song list, the track is added to
the end of the list.To delete the entire song list, perform the following
steps:
1. Turn the CD player on.
2. Press the song list button to turn song list on.
S-LIST displays.
3. Press and hold the song list button for more
than four seconds. A beep sounds, followed
by two beeps after two seconds, and a
nal beep sounds after four seconds. SONG
LIST EMPTY displays indicating that the
song list has been deleted.
If a CD is ejected, and the song list contains
saved tracks from that CD, those tracks are
automatically deleted from the song list. Any tracks
saved to the song list again are added to the
bottom of the list.
To end song list mode, press the song list button.
One beep sounds and S-LIST is removed from
the display.
244

CD Messages
CHECK CD:If this message appears on the
display and/or the CD comes out, it could be for
one of the following reasons:
It is very hot. When the temperature returns to
normal, the CD should play.
You are driving on a very rough road.
When the road becomes smoother, the CD
should play.
The CD is dirty, scratched, wet, or
upside down.
The air is very humid. If so, wait about an
hour and try again.
There may have been a problem while
burning the CD.
The label may be caught in the CD player.
If the CD is not playing correctly, for any other
reason, try a known good CD.
If any error occurs repeatedly or if an error cannot
be corrected, contact your dealer. If the radio
displays an error message, write it down
and provide it to your dealer when reporting the
problem.
245

XM Radio Messages
Radio Display Message Condition Action Required
XL (Explicit Language
Channels)XL on the radio display,
after the channel name,
indicates content with
explicit language.These channels, or any others, can be blocked at a
customer’s request, by calling 1-800-852-XMXM (9696).
Updating Updating encryption code The encryption code in the receiver is being updated, and
no action is required. This process should take no longer
than 30 seconds.
No Signal Loss of signal The system is functioning correctly, but the vehicle is in a
location that is blocking the XM™ signal. When the vehicle
is moved into an open area, the signal should return.
Loading XM Acquiring channel audio
(after 4 second delay)The audio system is acquiring and processing audio and
text data. No action is needed. This message should
disappear shortly.
CH Off Air Channel not in service This channel is not currently in service. Tune to another
channel.
CH Unavail Channel no longer
availableThis previously assigned channel is no longer assigned.
Tune to another station. If this station was one of the
presets, choose another station for that preset button.
No Info Artist Name/Feature
not availableNo artist information is available at this time on this channel.
The system is working properly.
No Info Song/Program Title
not availableNo song title information is available at this time on this
channel. The system is working properly.
246

Radio Display Message Condition Action Required
No Info Category Name
not availableNo category information is available at this time on this
channel. The system is working properly.
No Info No Text/Informational
message availableNo text or informational messages are available at this time
on this channel. The system is working properly.
Not Found No channel available for
the chosen categoryThere are no channels available for the selected category.
The system is working properly.
XM Locked Theft lock active The XM™ receiver in your vehicle may have previously
been in another vehicle. For security purposes, XM™
receivers cannot be swapped between vehicles. If this
message is received after having your vehicle serviced,
check with your dealer.
Radio ID Radio ID label (channel 0) If tuned to channel 0, this message alternates with the
XM™ Radio eight digit radio ID label. This label is needed
to activate the service.
Unknown Radio ID not known
(should only be if
hardware failure)If this message is received when tuned to channel 0, there
may be a receiver fault. Consult with your dealer.
Chk XMRcvr Hardware failure in the
receiver moduleIf this message does not clear within a short period of time,
the receiver may have a fault. Consult with your dealer.
247

Theft-Deterrent Feature
THEFTLOCK®is designed to discourage theft of
your vehicle’s radio. The feature works
automatically by learning a portion of the Vehicle
Identication Number (VIN). If the radio is
moved to a different vehicle, it does not operate
and LOCKED displays.
With THEFTLOCK
®activated, the radio cannot
operate if stolen.
Audio Steering Wheel Controls
If your vehicle has this
feature, some audio
controls can be adjusted
at the steering wheel.
They include the
following:
xw:Press the up or the down arrow to go to
the next or to the previous radio station and
stay there. The radio only seeks stations with a
strong signal that are in the selected band.
To scan stations, press and hold either arrow for
two seconds until SCAN displays and a beep
sounds. The radio goes to a station, plays for a
few seconds, then goes to the next station. Press
either arrow again to stop scanning.
When a CD is playing, press the up or the down
arrow to go to the next or previous track.
To scan the current CD, press and hold either up
or down arrow for more than two seconds. The
CD goes to the next track, plays the rst
10 seconds, then goes to the next track. Press
either up or down arrow again to stop scanning.
To scan all of the CDs loaded, press and hold either
up or down arrow for more than four seconds. The
CD goes to the next CD, plays the rst 10 seconds
of each track, then goes to the next CD. Press
either up or down arrow again to stop scanning.
248