2007 PONTIAC G5 Owners Manual

Notice:If your vehicle has a tire size other than
P205/55R16 or P205/50R17, use tire chains only
where legal and only when you must. Use only
SAE Class S-type chains that are the proper
size for your tires. Install them on the front tires
and tighten them as tightly as possible with the
ends securely fastened. Drive slowly and follow
the chain manufacturer’s instructions. If you
can hear the chains contacting your vehicle,
stop and retighten them. If the contact
continues, slow down until it stops. Driving
too fast or spinning the wheels with chains on
will damage your vehicle.
If a Tire Goes Flat
It is unusual for a tire to blowout while you are
driving, especially if you maintain your vehicle’s
tires properly. If air goes out of a tire, it is much
more likely to leak out slowly. But if you should ever
have a blowout, here are a few tips about what to
expect and what to do:
If a front tire fails, the at tire will create a drag that
pulls the vehicle toward that side. Take your foot off
the accelerator pedal and grip the steering wheel
rmly. Steer to maintain lane position, and then
gently brake to a stop well out of the traffic lane.A rear blowout, particularly on a curve, acts much
like a skid and may require the same correction you
would use in a skid. In any rear blowout remove
your foot from the accelerator pedal. Get the vehicle
under control by steering the way you want the
vehicle to go. It may be very bumpy and noisy, but
you can still steer. Gently brake to a stop, well off
the road if possible.
{CAUTION:
Lifting a vehicle and getting under it to
do maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a at
tire. If it is used for anything else, you or
others could be badly injured or killed if the
vehicle slips off the jack. Use the jack
provided with your vehicle only for
changing a at tire.
If a tire goes at, the next part shows how to use the
jacking equipment to change a at tire safely.
337

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place. Turn on
your hazard warning ashers.
{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire. To
help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put an automatic transaxle shift lever
in PARK (P), or shift a manual
transaxle to FIRST (1) or REVERSE (R).
CAUTION: (Continued)
CAUTION: (Continued)
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will
not move, you should put blocks at the
front and rear of the tire farthest away
from the one being changed. That would
be the tire on the other side, at the
opposite end of the vehicle.
When you have a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
338

The following information will tell you how to use
the jack and change a tire.
Removing the Spare Tire and Tools
The equipment you will need is located in
the trunk.
Base Models
1. Open the trunk. SeeTrunk on page 98for
more information.
2. Lift the trunk liner to access the spare tire
and tools.
339

A. Cover
B. Retainer
C. Spare Tire
D. Wing NutE. Jack and Wheel
Wrench
F. Bolt
3. Remove the retainer (B) that holds down the
spare tire. SeeCompact Spare Tire on
page 352for more information.
340

4. Remove the spare tire (C) by gently pulling it
up and out of the trunk.
5. Remove the wing nut (D) that holds the jack
and remove the jack and wheel wrench (E).Uplevel Models
1. Open the trunk. SeeTrunk on page 98for
more information.
2. Lift the trunk liner to access the spare tire
and tools.
341

A. Retainer
B. Jack and Wheel
WrenchC. Spare Tire
D. Foam Support
E. Bolt
3. Remove the retainer (A) that holds down the
jack, wheel wrench (B) and spare tire (C).
4. Remove the spare tire by gently pulling it up
and out of the trunk.
The tools you will be using include the jack (A)
and wheel wrench (B).
342

You will need to turn the plastic wheel nut
counterclockwise to loosen the wheel wrench
from the jack.Press the button and then pull on the end of the
wheel wrench to extend the handle.
343

Removing the Flat Tire and
Installing the Spare Tire
1. If your vehicle has plastic wheel covers, use
the wheel wrench to loosen the plastic wheel
nut caps.
Once you have loosened the plastic wheel nut
caps with the wheel wrench, you can nish
loosening them with your ngers. The plastic
nut caps do not come off.
2. Using the at end of the wheel wrench, pry
along the edge of the wheel cover until it
comes off.3. Use the wheel wrench to loosen all the wheel
nuts. Do not remove them yet.
4. It is recommended that you do a safety check
before preceding. SeeChanging a Flat Tire
on page 338for more information.
Notice:Make sure that the jack lift head is in
the correct position or you may damage your
vehicle. The repairs would not be covered by
your warranty.
5. Position the jack lift head at the jack
location nearest the at tire. The front
location is about 8 inches (20 cm)
behind the front wheel opening.
344