2007 NISSAN TIIDA auto switch

WW-56
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Rear wiper does not
operate.ON only Combination switch
 Harness between combination switch and BCM
BCMCombination switch
Refer to BCS-55, "
Symptom
Ta b l e".
INT only Combination switch
 Harness between combination switch and BCM
BCMCombination switch
Refer to BCS-55, "
Symptom
Ta b l e".
ON and INT Combination switch
 Harness between combination switch and BCM
BCMCombination switch
Refer to BCS-55, "
Symptom
Ta b l e".
BCM
 Harness between rear wiper motor and BCM
 Harness between rear wiper motor and ground
 Rear wiper motorCombination switch
Refer to WW-28, "
Compo-
nent Function Check".
Rear wiper does not
stop.ON only Combination switch
BCMRear wiper motor circuit
Refer to WW-30, "
Compo-
nent Function Check".
INT only Combination switch
BCMCombination switch
Refer to BCS-55, "
Symptom
Ta b l e".
Rear wiper does not
operate normally.Wiper is not linked to
the washer operation. Combination switch
 Harness between rear wiper motor and BCM
BCMCombination switch
Refer to BCS-55, "
Symptom
Ta b l e".
BCM —
Rear wiper does not
return to the Stop posi-
tion (Stops after a five-
second operation).BCM
 Harness between rear wiper motor and BCM
 Rear wiper motorRear wiper auto stop signal
circuit
Refer to WW-30, "
Compo-
nent Function Check". Rear wiper stops after
operating for five sec-
onds when ignition
switch is turned ON.
Headlamp washer
does not operate.Headlamp washer
does not operate with
the front washer when
headlamps are turned
ON. Combination switch
 Harness between combination switch and BCM
BCM
 Headlamp washer pumpCombination switch
Refer to BCS-55, "
Symptom
Ta b l e".
 Fusible link
 Harness between fusible link and headlamp
washer relay
 Headlamp washer relay
 Harness between headlamp washer relay and
IPDM E/R
 IPDM E/R
 Harness between headlamp washer relay and
headlamp washer pump
 Harness between headlamp washer pump and
ground
 Headlamp washer pumpHeadlamp washer circuit
Refer to WW-33, "
Compo-
nent Function Check".
BCM — Symptom Probable malfunction location Inspection item

WW-58
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
FRONT WIPER DOES NOT OPERATE
DescriptionINFOID:0000000001366642
The front wiper does not operate under any operation conditions.
Diagnosis ProcedureINFOID:0000000001366643
1. CHECK WIPER RELAY OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Start IPDM E/R auto active test. Refer to PCS-10, "
Diagnosis Description".
2. Check that the front wiper operates at the LO/HI operation.
CONSULT-III ACTIVE TEST
1. Select "FRONT WIPER" of IPDM E/R active test item.
2. While operating the test item, check front wiper operation.
Is front wiper operation normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK FRONT WIPER MOTOR FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not blown.
Is the fuse blown?
YES >> Replace the fuse after repairing the applicable circuit.
NO >> GO TO 3
3. CHECK FRONT WIPER MOTOR GROUND OPEN CIRCUIT
1. Disconnect front wiper motor.
2. Check continuity between front wiper motor harness connector
and ground.
Does continuity exist?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
CONSULT-III ACTIVE TESTLO : Front wiper LO operation
HI : Front wiper HI operation
OFF : Stop the front wiper.
Unit Location Fuse No. Capacity
Front wiper motor IPDM E/R 39 30 A
Front wiper motor
GroundContinuity
Connector Terminal
E1 2 Yes
WKIA5488E

WW-70
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
RHD Models
Removal and InstallationINFOID:0000000001449632
REMOVAL
1. Operate the front wiper to move it to the auto stop position.
2. Open the hood.
3. Remove the front wiper arm caps.
4. Remove the front wiper arm nuts.
5. Raise the front wiper arms, and remove the front wiper arms.
INSTALLATION
1. Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
2. Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it off (auto stop).
3. Push wiper arm onto pivot shaft, make sure it is correctly
meshed and fully seated on the spline.
ALLIA0278ZZ
1. Wiper arm cap 2. Front RH wiper arm 3. Wiper arm cap
4. Front LH wiper arm 5. Front wiper drive assembly 6. Front LH wiper blade
7. Front RH wiper blade Front
SEL024J

FRONT WIPER DRIVE ASSEMBLY
WW-73
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
RHD Models
Removal and InstallationINFOID:0000000001450837
REMOVAL
1. Operate the front wiper motor, and then turn off (auto stop).
2. Remove wiper arms. Refer to WW-70, "
Removal and Installation".
3. Remove cowl top cover. Refer to EXT-20, "
Removal and Installation".
4. Disconnect wiper motor connector.
5. Remove front wiper drive assembly bolts, and remove front wiper drive assembly.
INSTALLATION
1. Install front wiper drive assembly.
2. Connect wiper motor connector. Turn wiper switch on to operate wiper motor, then turn wiper switch off
(auto stop).
3. Install cowl top cover. Refer to EXT-20, "
Removal and Installation".
4. Install the wiper arms and adjust as necessary. Refer to WW-71, "
Adjustment".
AdjustmentINFOID:0000000001450764
WIPER BLADE POSITION ADJUSTMENT
ALLIA0278ZZ
1. Wiper arm cap 2. Front RH wiper arm 3. Wiper arm cap
4. Front LH wiper arm 5. Front wiper drive assembly 6. Front LH wiper blade
7. Front RH wiper blade