2007 NISSAN TIIDA engine oil

EM-284
< ON-VEHICLE REPAIR >[K9K]
OIL PAN
OIL PAN
Exploded ViewINFOID:0000000001381492
Removal and InstallationINFOID:0000000001381493
CAUTION:
To avoid the danger of being scalded, never drain the engine oil when the engine is hot.
REMOVAL
1. Remove engine undercover using power tool.
2. Remove oil level indicator.
3. Drain engine oil. Refer to LU-27, "
Draining".
CAUTION:
Perform when engine is cold.
4. Remove fender protector (RH).
5. Remove front driveshaft assembly (RH). Refer to FA X - 11 , "
Removal and Installation (Right Side)".
6. Remove driveshaft center bearing bracket.
7. Remove rear torque rod (lower). Refer to EM-302, "
Exploded View".
8. Remove bolts from the catalyst bracket. Refer to EM-274, "
Exploded View".
9. Disconnect and remove oil level sensor.
1. Gasket 2. Oil pan 3. O-ring
4. Drain plug 5. Oil level sensor 6. Clutch housing
7. Crankshaft position sensor
E1BIA0008GB

OIL PAN
EM-285
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
10. Remove oil pan and transaxle joint bolts.
11. Support the engine bottom of the oil pan with a transmission jack
etc.
12. Remove oil pan bolts in reverse order as shown.
13. Insert seal cutter [SST: KV10111100 (—)] between upper oil pan
and cylinder block. Slide tool by tapping on the side of the tool
with a hammer.
CAUTION:
Exercise care not to damage mating surface.
14. Remove oil pan.
INSTALLATION
 Installation is in the reverse order of removal.
MBIB1039E
MBIB0575E
MBIB1257E
SEM365EA

EM-286
< ON-VEHICLE REPAIR >[K9K]
OIL PAN
1. Apply liquid gasket as shown.
 Use Genuine Liquid Gasket or equivalent.
2. Using suitable tool, align the oil pan with the cylinder block.
3. Install oil pan bolts in numerical order as shown.
NOTE:
Wait at least 30 minutes after oil pan is installed before filling
engine with engine oil.
InspectionINFOID:0000000001381494
INSPECTION AFTER REMOVAL
Clean oil pump assembly if any objects attached.
INSPECTION AFTER INSTALLATION
 Check the engine oil level. Refer to LU-26, "Inspection".
 Start the engine and make sure there are no leaks of engine oil. Refer to LU-26, "
Inspection".
MBIB0593E
MBIB0594E
: 14.0 N·m (1.4 kg-m, 10 ft-lb)
MBIB1257E

HIGH PRESSURE SUPPLY PUMP
EM-287
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
HIGH PRESSURE SUPPLY PUMP
Exploded ViewINFOID:0000000001381495
Removal and InstallationINFOID:0000000001381496
REMOVAL
CAUTION:
 Be sure to read “Precautions for Diesel Equipment”. Refer to EM-253, "
Precaution for Diesel Equip-
ment".
 Wait until the fuel temperature drops before carrying out any work.
 Order the special high pressure injection circuit plug kit.
 It is strictly forbidden to remove any high pressure supply
pump sprocket marked number 070 575 (see diagram). If the
pump is being replaced, the pulley must be replaced.
1. Disconnect the battery.
2. Remove air duct (inlet). Refer to EM-269, "
Exploded View".
3. Remove engine cover.
4. Remove blow-by hose.
5. Remove charge air cooler hose and pipes. Refer to EM-270,
"Exploded View".
6. Remove the RH front tire. Refer to WT-6, "
Rotation".
7. Remove fender protector (RH). Refer to EXT-22, "
Removal and
Installation".
8. Remove drive belt. Refer to EM-263, "
Removal and Installation".
9. Support the engine using suitable tool.
10. Remove the timing belt. Refer to EM-291, "
Removal and Installation".
11. Remove the oil level gauge guide and plug the hole. Refer to EM-281, "
Exploded View".
12. Remove high pressure pipes protection cover (upper). Refer to EM-281, "
Exploded View".
13. Carefully disconnect:
 The connectors from the flow actuator,
 The connectors from the fuel temperature sensor,
 On the pump, the fuel supply and return pipes.
 The return pipe connecting the injectors with the pump.
14. Remove the injection tube connecting the pump to the rail. Refer to EM-281, "
Removal and Installation".
1. High pressure supply pump protec-
tor2. Stud bolt 3. High pressure supply pump
4. Engine cover bracket
E1BIA0119GB
MBIB9036E

ROCKER COVER
EM-289
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
ROCKER COVER
Exploded ViewINFOID:0000000001381497
Removal and InstallationINFOID:0000000001381498
REMOVAL
1. Remove engine cover.
2. Remove air duct (inlet). Refer to EM-269, "
Exploded View".
3. Remove air duct (suction). Refer to EM-269, "
Exploded View".
4. Remove charge air cooler pipes and hoses. Refer to EM-270, "
Exploded View".
5. Disconnect and remove camshaft position sensor.
6. Remove fuel hose shield.
7. Disconnect electronic throttle control actuator. Refer to EM-272, "
Exploded View".
8. Remove blow-by hose.
9. Remove high pressure pipes protection cover (upper).
10. Unclip fuel injector spill hose from rocker cover.
11. Unclip timing belt upper cover.
12. Remove rocker cover.
NOTE:
Loosen bolts in the reverse order as shown.
INSTALLATION
1. Install new gasket to rocker cover.
1. Oil filler cap 2. Rocker cover 3. Gasket
4. Camshaft position sensor
E1BIA0006GB
E1BIA0048ZZ

TIMING BELT
EM-291
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
TIMING BELT
Exploded ViewINFOID:0000000001381499
Removal and InstallationINFOID:0000000001381500
CAUTION:
 Apply new engine oil to parts marked in illustration before installation.
 Replace any belt that has been removed.
 Never turn the engine in the direction opposite to that of normal operation.
 When replacing the timing belt, be sure to replace the timing belt tensioner.
 Do not run the engine without the drive belts to avoid damaging the crankshaft pulley.
REMOVAL
1. Remove front wheel RH. Refer to WT-6, "Rotation".
2. Remove fender protector RH. Refer to EXT-22, "
Removal and Installation".
3. Remove engine cover.
4. Remove drive belt. Refer to EM-291, "
Removal and Installation".
5. Support the engine using suitable tool.
6. Remove RH engine torque rod.
7. Remove RH engine mounting support bracket and RH engine mounting insulator.
1. Timing belt inner cover 2. Timing belt 3. Camshaft sprocket
4. Camshaft sprocket stud bolt 5. Timing belt tensioner 6. Timing belt cover
7. Cylinder head suspended bracket 8. Crankshaft pulley 9. Crankshaft sprocket (timing belt)
10. Oil seal 11. Crankshaft cover 12. Gasket
A. 30.0 N·m (3.1 kg-m, 22 ft-lb) and 86 degrees
B. 120.0 N·m (12 kg-m, 89 ft-lb) and 95 degrees
E1BIA0022GB

EM-298
< ON-VEHICLE REPAIR >[K9K]
CAMSHAFT
CAMSHAFT
Exploded ViewINFOID:0000000001381501
Removal and InstallationINFOID:0000000001381502
CAUTION:
Apply new engine oil to parts marked in illustration before installation.
REMOVAL
1. Remove front wheel RH. Refer to WT-6, "Rotation".
2. Remove fender protector RH. Refer to EXT-22, "
Removal and Installation".
3. Remove rocker cover. Refer to EM-289, "
Removal and Installation".
4. Remove electronic throttle control actuator. Refer to EM-272, "
Exploded View".
5. Remove vacuum pump. Refer to EM-280, "
Removal and Installation".
6. Remove drive belt. Refer to EM-263, "
Removal and Installation".
7. Support the engine using suitable tool.
CAUTION:
Put a piece of wood or something similar as supporting surface to secure a completely stable con-
dition.
8. Remove timing belt. Refer to EM-291, "
Removal and Installation".
9. Remove camshaft brackets.
10. Remove camshaft.
11. Remove valve lifter.
INSTALLATION
1. Camshaft sprocket stud bolt 2. Camshaft sprocket 3. Oil seal
4. Camshaft bracket 5. Camshaft 6. Cylinder head suspended bracket
7. Valve lifter 8. Cap 9. Cylinder head
A. 30.0 N·m (3.1 kg-m, 22 ft-lb) and 86 degrees
E1BIA0023GB

EM-304
< REMOVAL AND INSTALLATION >[K9K]
ENGINE ASSEMBLY
1. Install engine slingers (1) into front right of cylinder head and
engine slinger (2) into rear left of cylinder head.
2. Remove upper torque rod.
3. Use a manual lift table caddy (commercial service tool) or equiv-
alently rigid tool such as a jack or trestle. Securely support bot-
tom of engine and transaxle.
CAUTION:
Put a piece of wood or something similar at the supporting
surface to secure a stable condition.
4. Remove RH and LH engine mounting bolts.
5. Remove engine and transaxle assembly from vehicle downward
by carefully operating supporting tools.
CAUTION:
 During the operation, make sure that no part interferes with body side.
 Before and during this lifting, always check if any harnesses are left connected.
 During the removal operation, always be careful to prevent vehicle from falling off the lift due to
changes in the center of gravity.
 If necessary, support vehicle by setting a jack or equivalent tool at the rear.
Separation Work
CAUTION:
During the operation, secure the engine by placing a piece of wood under the engine oil pan and tran-
saxle and lift the engine using a suitable tool.
1. Remove starter motor.
2. Separate engine and transaxle.
3. Lift the engine with a suitable tool and separate the engine from the transaxle assembly. Refer to EM-302,
"Exploded View".
INSTALLATION
Installation is in the reverse order of removal.
 Do not allow oil to get on mounting insulator. Be careful not to damage mounting insulator.
 When installation directions are specified, install parts according to the direction marks on them referring to
exploded views.
 Make sure that each mounting insulator is seated properly, and tighten mounting bolts and nuts.
InspectionINFOID:0000000001381506
INSPECTION AFTER INSTALLATION
 Before starting engine check the levels of coolant, lubricants and oils. Fill to the specified level.
 Before starting engine, bleed air from fuel piping. Refer to EM-287, "
Removal and Installation".
 Run engine to check for unusual noise and vibration.
 Warm up engine thoroughly to make sure there is no leakage of coolant, lubricants, oil, fuel and exhaust
gas.
 Bleed air from passages in pipes and tubes of applicable lines.
MBIB9022E