2007 NISSAN TIIDA keyless entry

DOOR LOCK FUNCTION
DLK-23
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DOOR LOCK AND UNLOCK SWITCH : Component DescriptionINFOID:0000000001396465
INTELLIGENT KEY
INTELLIGENT KEY : System DiagramINFOID:0000000001396466
INTELLIGENT KEY OPERATION
INTELLIGENT KEY : System DescriptionINFOID:0000000001396467
INTELLIGENT KEY OPERATION
The Intelligent Key has the same functions as the remote keyless entry system. In addition to other safety fea-
tures, it can be used to lock and unlock all doors including the back door (hatchback) or the trunk (sedan).
This function can be set to OFF with CONSULT-III. For the setting information, refer to DLK-53, "
CONSULT-III
Function (INTELLIGENT KEY)".
OPERATION CONDITION
OPERATION AREA
To ensure that the Intelligent Key works effectively, use within a 100 cm range of each door, however the oper-
able range may differ according to surroundings.
DOOR LOCK AND UNLOCK CONTROL
When door lock and unlock button of the Intelligent Key are pressed, lock signal or unlock signal is transmitted
from Intelligent Key to Intelligent Key unit.
When Intelligent Key unit receives the door lock and unlock signal, it operates door lock actuator.
Item Function
BCM Controls the door lock function.
Door switch Detects door state (open or close).
Door lock and unlock switchTransmits door lock/unlock signal to BCM. Door lock/unlock switch indicator is built-in door
lock and unlock switch.
Door lock actuator Receives door lock/unlock signal from BCM and locks/unlocks each door.
ALKIA0711GB
Remote controller operation Operation condition
Lock All doors are closed
 Key switch is OFF (key is removed from ignition key cylinder)
 Ignition knob switch is OFF (Ignition switch is not pressed)
Unlock Key switch is OFF (key is removed from ignition key cylinder)
 Ignition knob switch is OFF (Ignition switch is not pressed)

DLK-50
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)INFOID:0000000001396502
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)INFOID:0000000001396503
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to XX-XX, "*****"
.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
CONFIGURATION Enables to read and save the vehicle specification.
 Enables to write the vehicle specification when replacing BCM.
System Sub system selection itemDiagnosis mode
WORK SUPPORT DATA MONITOR ACTIVE TEST
—BCM×
Door lock DOOR LOCK×××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Interior room lamp timer INT LAMP×××
Remote keyless entry system MULTI REMOTE ENT×××
Exterior lamp HEAD LAMP×××
Wiper and washer WIPER×××
Turn signal and hazard warning lamps FLASHER××
Air conditioner AIR CONDITONER×
Intelligent Key system INTELLIGENT KEY×
Combination switch COMB SW×
Immobilizer IMMU××
Interior room lamp battery saver BATTERY SAVER×××
Trunk open TRUNK×
Vehicle security system THEFT ALM×××
Signal buffer system SIGNAL BUFFER××
PTC heater system PTC HEATER××

DLK-150
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
INTELLIGENT KEY BATTERY AND FUNCTION
INTELLIGENT KEY BATTERY AND FUNCTION
DescriptionINFOID:0000000001516665
The following functions are available when having and carrying the Intelligent Key.
 Door lock/unlock
 Back door open (hatchback)
 Trunk lid release (sedan)
 Engine start
Remote control entry function is available when operating the remote buttons.
Component Function CheckINFOID:0000000001516666
1.CHECK FUNCTION
With CONSULT-III
Check remote keyless entry receiver "RKE OPE COUN1" in DATA MONITOR mode with CONSULT-III.
Is the inspection result normal?
YES >> Intelligent Key is OK.
NO >> Refer to DLK-150, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001516667
1.CHECK INTELLIGENT KEY FUNCTION
Do doors lock and unlock when using the Intelligent Key buttons?
YES or NO?
YES >> Intelligent Key is OK.
NO >> GO TO 2.
2.CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300Ω) so that the
current value becomes about 10 mA.
Is the measurement value within specification?
YES >> Intelligent Key battery is OK.
NO >> Replace Intelligent Key battery.
Component InspectionINFOID:0000000001516668
For battery removal and installation, refer to XX-XX, "*****".
Special Repair RequirementINFOID:0000000001516669
Refer to CONSULT-III Operation Manual.
Monitor item Condition
RKE OPE COUN1 Check that the numerical value is changing while operating the Intelligent Key.
Standard : Approx. 2.5 - 3.0V
OCC0607D

DIAGNOSIS SYSTEM (BCM)
DLK-275
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)INFOID:0000000001396710
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)INFOID:0000000001396711
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to XX-XX, "*****"
.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
CONFIGURATION Enables to read and save the vehicle specification.
 Enables to write the vehicle specification when replacing BCM.
System Sub system selection itemDiagnosis mode
WORK SUPPORT DATA MONITOR ACTIVE TEST
—BCM×
Door lock DOOR LOCK×××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Interior room lamp timer INT LAMP×××
Remote keyless entry system MULTI REMOTE ENT×××
Exterior lamp HEAD LAMP×××
Wiper and washer WIPER×××
Turn signal and hazard warning lamps FLASHER××
Air conditioner AIR CONDITONER×
Intelligent Key system INTELLIGENT KEY×
Combination switch COMB SW×
Immobilizer IMMU××
Interior room lamp battery saver BATTERY SAVER×××
Trunk open TRUNK×
Vehicle security system THEFT ALM×××
Signal buffer system SIGNAL BUFFER××
PTC heater system PTC HEATER××

DLK-380
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
INTELLIGENT KEY BATTERY AND FUNCTION
INTELLIGENT KEY BATTERY AND FUNCTION
DescriptionINFOID:0000000001530384
The following functions are available when having and carrying the Intelligent Key.
 Door lock/unlock
 Back door open (hatchback)
 Trunk lid release (sedan)
 Engine start
Remote control entry function is available when operating the remote buttons.
Component Function CheckINFOID:0000000001530385
1.CHECK FUNCTION
With CONSULT-III
Check remote keyless entry receiver "RKE OPE COUN1" in DATA MONITOR mode with CONSULT-III.
Is the inspection result normal?
YES >> Intelligent Key is OK.
NO >> Refer to DLK-380, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001530386
1.CHECK INTELLIGENT KEY FUNCTION
Do doors lock and unlock when using the Intelligent Key buttons?
YES or NO?
YES >> Intelligent Key is OK.
NO >> GO TO 2.
2.CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300Ω) so that the
current value becomes about 10 mA.
Is the measurement value within specification?
YES >> Intelligent Key battery is OK.
NO >> Replace Intelligent Key battery.
Component InspectionINFOID:0000000001530387
For battery removal and installation, refer to XX-XX, "*****".
Special Repair RequirementINFOID:0000000001530388
Refer to CONSULT-III Operation Manual.
Monitor item Condition
RKE OPE COUN1 Check that the numerical value is changing while operating the Intelligent Key.
Standard : Approx. 2.5 - 3.0V
OCC0607D

DOOR LOCK FUNCTION
DLK-475
< FUNCTION DIAGNOSIS >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DOOR LOCK AND UNLOCK SWITCH : Component DescriptionINFOID:0000000001396991
REMOTE KEYLESS ENTRY
REMOTE KEYLESS ENTRY : System DiagramINFOID:0000000001396992
KEYFOB OPERATION
REMOTE KEYLESS ENTRY : System DescriptionINFOID:0000000001396993
KEYFOB OPERATION
The multi remote control system can be locked and unlocked by pressing door lock and unlock button of key-
fob.
DOOR LOCK AND UNLOCK OPERATION
When door lock and unlock button of keyfob is pressed, door lock
and unlock signal transmits from keyfob to BCM. When BCM
receives the door lock and unlock signal, it operates door lock actua-
tor.
1. Integrated door lock keyfob.
2. Integrated ignition key/emergency key.
3. Key number plate.
OPERATION CONDITION
OPERATION AREA
To ensure that the keyfob works effectively, use within 100 cm range of each door, however the operable
range may differ according to surroundings.
Item Function
BCM Controls the door lock and unlock function.
Door switch Detects door state (open or closed).
Door lock and unlock switchTransmits door lock and unlock signal to BCM. Door lock and unlock switch indicator is built
in door lock and unlock switch.
Door lock actuator Receives door lock and unlock signal from BCM and locks and unlocks each door.
ALKIA0836GB
ALKIA0821ZZ
Remote controller operation Operation condition
Lock/unlock Key switch is OFF (key is removed from ignition key cylinder).

DLK-476
< FUNCTION DIAGNOSIS >[WITHOUT I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
ANTI-HIJACK MODE
When door lock is unlocked, pressing LOCK button on keyfob once will lock all doors. When door lock is
locked, pressing UNLOCK button on keyfob will unlock driver side door. Pressing UNLOCK button on keyfob
second time within 5 seconds from the first time will unlock all doors and back door can be opened with back
door opener switch.
NOTE:
Anti-hijack mode can be set to ON or OFF with CONSULT-III. For the setting information, refer to DLK-490,
"MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)".
REMOTE KEYLESS ENTRY : Component Parts LocationINFOID:0000000001396994
ALKIA0817ZZ
1. BCM M18, M19, M20
(view with glove box removed)2. Front door switch (driver side) B34
(Passenger side) B273. Rear door switch LH B71
RH B53
4. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)5. Key switch and key lock solenoid
M276. Trunk lid opener switch (sedan) B61
7. Back door opener switch (hatchback) D408

DOOR LOCK FUNCTION
DLK-477
< FUNCTION DIAGNOSIS >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REMOTE KEYLESS ENTRY : Component DescriptionINFOID:0000000001396995
Item Function
BCM Controls the door lock function.
Key switch Detects that ignition key is inserted into ignition key cylinder.
Door lock actuator Receives lock and unlock signal from BCM and locks and unlocks each door.